.\" $NetBSD: xfer,v 1.2.38.2 2020/03/29 11:59:06 martin Exp $ .\" .\" Copyright (c) 1999-2004 The NetBSD Foundation, Inc. .\" All rights reserved. .\" .\" Redistribution and use in source and binary forms, with or without .\" modification, are permitted provided that the following conditions .\" are met: .\" 1. Redistributions of source code must retain the above copyright .\" notice, this list of conditions and the following disclaimer. .\" 2. Redistributions in binary form must reproduce the above copyright .\" notice, this list of conditions and the following disclaimer in the .\" documentation and/or other materials provided with the distribution. .\" .\" THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS .\" ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED .\" TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR .\" PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS .\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR .\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF .\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS .\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN .\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) .\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE .\" POSSIBILITY OF SUCH DAMAGE. .\" . .\" ---------- MD instructions on setting up boot media . .(Note .Nx*M \*V does not support any framebuffers other than NWB-253 on NWS-3470D and XA on NWS-5000 (yet) so you have to use serial console on installation procedure if your machine doesn't have supported framebuffers listed above. .Note) .Pp You will need to have two 1.44 MB floppy disks to boot off. You must put the boot floppy image onto this disk, which contains software to install .Nx system. .Pp If you are using a .Ul system (such as .Tn NEWS-OS or other .Nx machines) to write the floppy images to disks, you should use the .Xr dd 1 command to copy the file system image(s) (.fs file(s)) directly to the raw floppy disk. .Pp If you have an i386 machine which runs .Tn Microsoft Windows and use it to write the floppy image(s) to floppy disk, you can use the .Ic Rawrite32 Windows program. It can be downloaded from .Lk https://www.NetBSD.org/~martin/rawrite32 .Ic rawrite utility for the .Tn MS-DOS environment is also available in the .Pa i386/installation/misc/ directory of i386 install media. .Pp Though .Nx*M uses the floppy disk to boot for the initial installation, the .Nx*M kernel does not support the floppy device. Some other machines or systems are still required to write floppy images even after .Nx*M has been installed. .Pp If your machine doesn't have any SCSI disks, or the SCSI interface on your machine is not supported, it can still run .Nx*M diskless. No file transfer is needed, and all you have to do is to prepare files on the server. More information about diskless setups can be found at .Lk http://www.NetBSD.org/docs/network/netboot/ .Pp On NWS-3xxx machines, the PROM also supports network boot but it uses an unusual protocol which is not supported by .Nx*M . On NWS-5000 machines, the PROM uses the ordinary tftp protocol, so you can load bootloader via network by .Ic "bo tftp()" command on the PROM prompt. .Pp The .Tn NEWS PROM also supports tape boot, but .Nx*M does not support that currently. .Pp After the boot floppy is prepared, just type .Ic "bo fd" (NWS-5000) or .Ic "bo fh" (NWS-3xxx) on the PROM prompt to boot it. .Pp . .\" --------- MI instructions for getting distribution off installation medium . .so ../common/xfer