patch-2.4.9 linux/include/asm-arm/arch-sa1100/simpad.h

• Lines: 109
• Date: Sun Aug 12 17:36:24 2001
• Orig file: v2.4.8/linux/include/asm-arm/arch-sa1100/simpad.h
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.4.8/linux/include/asm-arm/arch-sa1100/simpad.h linux/include/asm-arm/arch-sa1100/simpad.h
@@ -0,0 +1,108 @@
+/*
+ * linux/include/asm-arm/arch-sa1100/trizeps.h
+ *
+ * based of assabet.h same as HUW_Webpanel
+ *
+ * This file contains the hardware specific definitions for Trizeps
+ *
+ * 2001/03/14 Peter Lueg <peter.lueg@dsa-ac.de>
+ */
+
+#ifndef SIMPAD_H
+#define SIMPAD_H
+
+
+#ifndef __ASM_ARCH_HARDWARE_H
+#error "include <asm/hardware.h> instead"
+#endif
+
+/* System Configuration Register flags */
+
+#define SCR_SDRAM_LOW	(1<<2)	/* SDRAM size (low bit) */
+#define SCR_SDRAM_HIGH	(1<<3)	/* SDRAM size (high bit) */
+#define SCR_FLASH_LOW	(1<<4)	/* Flash size (low bit) */
+#define SCR_FLASH_HIGH	(1<<5)	/* Flash size (high bit) */
+#define SCR_GFX		(1<<8)	/* Graphics Accelerator (0 = present) */
+#define SCR_SA1111	(1<<9)	/* Neponset (0 = present) */
+
+#define SCR_INIT	-1
+
+#define GPIO_UART1_RTS	GPIO_GPIO14
+#define GPIO_UART1_DTR	GPIO_GPIO7
+#define GPIO_UART1_CTS	GPIO_GPIO8
+#define GPIO_UART1_DCD	GPIO_GPIO23
+#define GPIO_UART1_DSR	GPIO_GPIO6
+
+#define GPIO_UART3_RTS	GPIO_GPIO12
+#define GPIO_UART3_DTR	GPIO_GPIO16
+#define GPIO_UART3_CTS	GPIO_GPIO13
+#define GPIO_UART3_DCD	GPIO_GPIO18
+#define GPIO_UART3_DSR	GPIO_GPIO17
+
+#define IRQ_UART1_CTS	IRQ_GPIO15
+#define IRQ_UART1_DCD	GPIO_GPIO23
+#define IRQ_UART1_DSR	GPIO_GPIO6
+#define IRQ_UART3_CTS	GPIO_GPIO13
+#define IRQ_UART3_DCD	GPIO_GPIO18
+#define IRQ_UART3_DSR	GPIO_GPIO17
+
+#define GPIO_UCB1300_IRQ	GPIO_GPIO (22)	/* UCB GPIO and touchscreen */
+#define IRQ_GPIO_UCB1300_IRQ IRQ_GPIO22
+
+#define SA1100_UART1_EXT \
+  (struct huw_irq_desc){GPIO_UART1_CTS, IRQ_UART1_CTS, \
+                        GPIO_UART1_DCD, IRQ_UART1_DCD, \
+                        GPIO_UART1_DSR, IRQ_UART1_DSR}
+#define SA1100_UART3_EXT \
+  (struct huw_irq_desc){GPIO_UART3_CTS, IRQ_UART3_CTS, \
+                        GPIO_UART3_DCD, IRQ_UART3_DCD, \
+                        GPIO_UART3_DSR, IRQ_UART3_DSR}
+
+
+/*---  PCMCIA  ---*/
+#define GPIO_CF_CD              GPIO_GPIO24
+#define GPIO_CF_IRQ             GPIO_GPIO1
+#define IRQ_GPIO_CF_IRQ         IRQ_GPIO1
+#define IRQ_GPIO_CF_CD          IRQ_GPIO24
+
+// CS3 Latch is write only, a shadow is neccessary
+
+#define CS3BUSTYPE unsigned volatile long
+#define CS3_BASE        0xf1000000
+
+#define VCC_5V_EN       0x0001
+#define VCC_3V_EN       0x0002
+#define EN1             0x0004
+#define EN0             0x0008
+#define DISPLAY_ON      0x0010
+#define PCMCIA_BUFF_DIS 0x0020
+#define MQ_RESET        0x0040
+#define PCMCIA_RESET    0x0080
+#define DECT_POWER_ON   0x0100
+#define IRDA_SD         0x0200
+#define RS232_ON        0x0400
+#define SD_MEDIAQ       0x0800
+#define LED2_ON         0x1000
+#define IRDA_MODE       0x2000
+#define ENABLE_5V       0x4000
+#define RESET_SIMCARD   0x8000
+
+#define RS232_ENABLE    0x0440
+#define PCMCIAMASK      0x402f
+
+#ifndef __ASSEMBLY__
+static long cs3_shadow;
+void init_simpad_cs3();
+void PCMCIA_setbit(int value);
+void PCMCIA_clearbit(int value);
+#endif
+
+#endif // SIMPAD_H
+
+
+
+
+
+
+
+