patch-2.4.6 linux/arch/sh/kernel/pci-7751se.c

Next file: linux/arch/sh/kernel/pci-bigsur.c
Previous file: linux/arch/sh/kernel/mach_dc.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.4.5/linux/arch/sh/kernel/pci-7751se.c linux/arch/sh/kernel/pci-7751se.c
@@ -0,0 +1,102 @@
+/*
+ * linux/arch/sh/kernel/pci-7751se.c
+ *
+ * Author:  Ian DaSilva (idasilva@mvista.com)
+ *
+ * Highly leveraged from pci-bigsur.c, written by Dustin McIntire.
+ *
+ * May be copied or modified under the terms of the GNU General Public
+ * License.  See linux/COPYING for more information.
+ *
+ * PCI initialization for the Hitachi SH7751 Solution Engine board (MS7751SE01)
+ */
+
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+
+#include <asm/io.h>
+#include <asm/pci-sh7751.h>
+
+#define PCIMCR_MRSET_OFF	0xBFFFFFFF
+#define PCIMCR_RFSH_OFF		0xFFFFFFFB
+
+/*
+ * Only long word accesses of the PCIC's internal local registers and the
+ * configuration registers from the CPU is supported.
+ */
+#define PCIC_WRITE(x,v) writel((v), PCI_REG(x))
+#define PCIC_READ(x) readl(PCI_REG(x))
+
+/*
+ * Description:  This function sets up and initializes the pcic, sets
+ * up the BARS, maps the DRAM into the address space etc, etc.
+ */
+int __init pcibios_init_platform(void)
+{
+   unsigned long data;
+   unsigned long bcr1, wcr1, wcr2, wcr3, mcr;
+   unsigned short bcr2;
+
+   //
+   // Initialize the slave bus controller on the pcic.  The values used
+   // here should not be hardcoded, but they should be taken from the bsc
+   // on the processor, to make this function as generic as possible.
+   // (i.e. Another sbc may usr different SDRAM timing settings -- in order
+   // for the pcic to work, its settings need to be exactly the same.)
+   //
+   bcr1 = (*(volatile unsigned long*)(SH7751_BCR1));
+   bcr2 = (*(volatile unsigned short*)(SH7751_BCR2));
+   wcr1 = (*(volatile unsigned long*)(SH7751_WCR1));
+   wcr2 = (*(volatile unsigned long*)(SH7751_WCR2));
+   wcr3 = (*(volatile unsigned long*)(SH7751_WCR3));
+   mcr = (*(volatile unsigned long*)(SH7751_MCR));
+
+   bcr1 = bcr1 | 0x00080000;  /* Enable Bit 19, BREQEN */
+   (*(volatile unsigned long*)(SH7751_BCR1)) = bcr1;   
+
+   bcr1 = bcr1 | 0x40080000;  /* Enable Bit 19 BREQEN, set PCIC to slave */
+   PCIC_WRITE(SH7751_PCIBCR1, bcr1);	 /* PCIC BCR1 */
+   PCIC_WRITE(SH7751_PCIBCR2, bcr2);     /* PCIC BCR2 */
+   PCIC_WRITE(SH7751_PCIWCR1, wcr1);     /* PCIC WCR1 */
+   PCIC_WRITE(SH7751_PCIWCR2, wcr2);     /* PCIC WCR2 */
+   PCIC_WRITE(SH7751_PCIWCR3, wcr3);     /* PCIC WCR3 */
+   mcr = (mcr & PCIMCR_MRSET_OFF) & PCIMCR_RFSH_OFF;
+   PCIC_WRITE(SH7751_PCIMCR, mcr);      /* PCIC MCR */
+
+   PCIC_WRITE(SH7751_PCIINTM, 0x0000c3ff);
+   PCIC_WRITE(SH7751_PCIAINTM, 0x0000980f);
+   PCIC_WRITE(SH7751_PCICONF1, 0xF39000C7);  /* FB9000C7 */
+   PCIC_WRITE(SH7751_PCICONF2, 0x00000000);  /* PCI Class code & Revision ID */
+   PCIC_WRITE(SH7751_PCICONF4, 0xab000001);  /* PCI I/O */
+   PCIC_WRITE(SH7751_PCICONF5, 0x0c000000);  /* PCI MEM0 old val: 0xb0000000 */
+   PCIC_WRITE(SH7751_PCICONF6, 0xd0000000);  /* PCI MEM1 */
+   PCIC_WRITE(SH7751_PCICONF11, 0x35051054); /* PCI Sub system ID & Sub system vendor ID */
+   PCIC_WRITE(SH7751_PCILSR0, 0x03f00000);   /* PCI MEM0 */
+   PCIC_WRITE(SH7751_PCILSR1, 0x00000000);   /* PCI MEM1 */
+   PCIC_WRITE(SH7751_PCILAR0, 0x0c000000);   /* MEM0 */
+   PCIC_WRITE(SH7751_PCILAR1, 0x00000000);   /* MEM1 */
+
+   PCIC_WRITE(SH7751_PCICR, 0xa5000001);
+
+   printk("SH7751 PCI: Finished initialization of the PCI controller\n");
+
+   return 1;
+}
+
+int __init pcibios_map_platform_irq(u8 slot, u8 pin)
+{
+        switch (slot) {
+        case 0: return 13;
+        case 1: return 13; 	/* AMD Ethernet controller */
+        case 2: return -1;
+        case 3: return -1;
+        case 4: return -1;
+        default:
+                printk("PCI: Bad IRQ mapping request for slot %d\n", slot);
+                return -1;
+        }
+}

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)