patch-2.4.5 linux/drivers/net/pcmcia/hermes.h

Next file: linux/drivers/net/pcmcia/orinoco_cs.c
Previous file: linux/drivers/net/pcmcia/hermes.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.4.4/linux/drivers/net/pcmcia/hermes.h linux/drivers/net/pcmcia/hermes.h
@@ -1,402 +0,0 @@
-/* hermes.h
- *
- * Driver core for the "Hermes" wireless MAC controller, as used in
- * the Lucent Orinoco and Cabletron RoamAbout cards. It should also
- * work on the hfa3841 and hfa3842 MAC controller chips used in the
- * Prism I & II chipsets.
- *
- * This is not a complete driver, just low-level access routines for
- * the MAC controller itself.
- *
- * Based on the prism2 driver from Absolute Value Systems' linux-wlan
- * project, the Linux wvlan_cs driver, Lucent's HCF-Light
- * (wvlan_hcf.c) library, and the NetBSD wireless driver.
- *
- * Copyright (C) 2000, David Gibson, Linuxcare Australia <hermes@gibson.dropbear.id.au>
- *
- * Portions taken from hfa384x.h, Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved.
- *
- * This file distributed under the GPL, version 2.
- */
-
-#ifndef _HERMES_H
-#define _HERMES_H
-
-/* Notes on locking:
- *
- * As a module of low level hardware access routines, there is no
- * locking. Users of this module should ensure that they serialize
- * access to the hermes_t structure, and to the hardware
-*/
-
-#include <linux/delay.h>
-#include <linux/if_ether.h>
-
-/*
- * Limits and constants
- */
-#define		HERMES_ALLOC_LEN_MIN		(4)
-#define		HERMES_ALLOC_LEN_MAX		(2400)
-#define		HERMES_LTV_LEN_MAX		(34)
-#define		HERMES_BAP_DATALEN_MAX		(4096)
-#define		HERMES_BAP_OFFSET_MAX		(4096)
-#define		HERMES_PORTID_MAX		(7)
-#define		HERMES_NUMPORTS_MAX		(HERMES_PORTID_MAX+1)
-#define		HERMES_PDR_LEN_MAX		(260)	/* in bytes, from EK */
-#define		HERMES_PDA_RECS_MAX		(200)	/* a guess */
-#define		HERMES_PDA_LEN_MAX		(1024)	/* in bytes, from EK */
-#define		HERMES_SCANRESULT_MAX		(35)
-#define		HERMES_CHINFORESULT_MAX		(8)
-#define		HERMES_FRAME_LEN_MAX		(2304)
-#define		HERMES_MAX_MULTICAST		(16)
-#define		HERMES_MAGIC			(0x7d1f)
-
-/*
- * Hermes register offsets
- */
-#define		HERMES_CMD			(0x00)
-#define		HERMES_PARAM0			(0x02)
-#define		HERMES_PARAM1			(0x04)
-#define		HERMES_PARAM2			(0x06)
-#define		HERMES_STATUS			(0x08)
-#define		HERMES_RESP0			(0x0A)
-#define		HERMES_RESP1			(0x0C)
-#define		HERMES_RESP2			(0x0E)
-#define		HERMES_INFOFID			(0x10)
-#define		HERMES_RXFID			(0x20)
-#define		HERMES_ALLOCFID			(0x22)
-#define		HERMES_TXCOMPLFID		(0x24)
-#define		HERMES_SELECT0			(0x18)
-#define		HERMES_OFFSET0			(0x1C)
-#define		HERMES_DATA0			(0x36)
-#define		HERMES_SELECT1			(0x1A)
-#define		HERMES_OFFSET1			(0x1E)
-#define		HERMES_DATA1			(0x38)
-#define		HERMES_EVSTAT			(0x30)
-#define		HERMES_INTEN			(0x32)
-#define		HERMES_EVACK			(0x34)
-#define		HERMES_CONTROL			(0x14)
-#define		HERMES_SWSUPPORT0		(0x28)
-#define		HERMES_SWSUPPORT1		(0x2A)
-#define		HERMES_SWSUPPORT2		(0x2C)
-#define		HERMES_AUXPAGE			(0x3A)
-#define		HERMES_AUXOFFSET		(0x3C)
-#define		HERMES_AUXDATA			(0x3E)
-
-/*
- * CMD register bitmasks
- */
-#define		HERMES_CMD_BUSY			(0x8000)
-#define		HERMES_CMD_AINFO		(0x7f00)
-#define		HERMES_CMD_MACPORT		(0x0700)
-#define		HERMES_CMD_RECL			(0x0100)
-#define		HERMES_CMD_WRITE		(0x0100)
-#define		HERMES_CMD_PROGMODE		(0x0300)
-#define		HERMES_CMD_CMDCODE		(0x003f)
-
-/*
- * STATUS register bitmasks
- */
-#define		HERMES_STATUS_RESULT		(0x7f00)
-#define		HERMES_STATUS_CMDCODE		(0x003f)
-
-/*
- * OFFSET refister bitmasks
- */
-#define		HERMES_OFFSET_BUSY		(0x8000)
-#define		HERMES_OFFSET_ERR		(0x4000)
-#define		HERMES_OFFSET_DATAOFF		(0x0ffe)
-
-/*
- * Event register bitmasks (INTEN, EVSTAT, EVACK)
- */
-#define		HERMES_EV_TICK			(0x8000)
-#define		HERMES_EV_WTERR			(0x4000)
-#define		HERMES_EV_INFDROP		(0x2000)
-#define		HERMES_EV_INFO			(0x0080)
-#define		HERMES_EV_DTIM			(0x0020)
-#define		HERMES_EV_CMD			(0x0010)
-#define		HERMES_EV_ALLOC			(0x0008)
-#define		HERMES_EV_TXEXC			(0x0004)
-#define		HERMES_EV_TX			(0x0002)
-#define		HERMES_EV_RX			(0x0001)
-
-/*
- * Command codes
- */
-/*--- Controller Commands --------------------------*/
-#define		HERMES_CMD_INIT			(0x0000)
-#define		HERMES_CMD_ENABLE		(0x0001)
-#define		HERMES_CMD_DISABLE		(0x0002)
-#define		HERMES_CMD_DIAG			(0x0003)
-
-/*--- Buffer Mgmt Commands --------------------------*/
-#define		HERMES_CMD_ALLOC		(0x000A)
-#define		HERMES_CMD_TX			(0x000B)
-#define		HERMES_CMD_CLRPRST		(0x0012)
-
-/*--- Regulate Commands --------------------------*/
-#define		HERMES_CMD_NOTIFY		(0x0010)
-#define		HERMES_CMD_INQ			(0x0011)
-
-/*--- Configure Commands --------------------------*/
-#define		HERMES_CMD_ACCESS		(0x0021)
-#define		HERMES_CMD_DOWNLD		(0x0022)
-
-/*--- Debugging Commands -----------------------------*/
-#define 	HERMES_CMD_MONITOR		(0x0038)
-#define		HERMES_MONITOR_ENABLE		(0x000b)
-#define		HERMES_MONITOR_DISABLE		(0x000f)
-
-/*
- * Configuration RIDs
- */
-
-#define		HERMES_RID_CNF_PORTTYPE		(0xfc00)
-#define		HERMES_RID_CNF_MACADDR		(0xfc01)
-#define		HERMES_RID_CNF_DESIRED_SSID	(0xfc02)
-#define		HERMES_RID_CNF_CHANNEL		(0xfc03)
-#define		HERMES_RID_CNF_OWN_SSID		(0xfc04)
-#define		HERMES_RID_CNF_SYSTEM_SCALE	(0xfc06)
-#define		HERMES_RID_CNF_MAX_DATA_LEN	(0xfc07)
-#define		HERMES_RID_CNF_PM_ENABLE	(0xfc09)
-#define		HERMES_RID_CNF_PM_MCAST_RX	(0xfc0b)
-#define		HERMES_RID_CNF_PM_PERIOD	(0xfc0c)
-#define		HERMES_RID_CNF_PM_HOLDOVER	(0xfc0d)
-#define		HERMES_RID_CNF_NICKNAME		(0xfc0e)
-#define		HERMES_RID_CNF_WEP_ON		(0xfc20)
-#define		HERMES_RID_CNF_MWO_ROBUST	(0xfc25)
-#define		HERMES_RID_CNF_PRISM2_WEP_ON	(0xfc28)
-#define		HERMES_RID_CNF_MULTICAST_LIST	(0xfc80)
-#define		HERMES_RID_CNF_CREATEIBSS	(0xfc81)
-#define		HERMES_RID_CNF_FRAG_THRESH	(0xfc82)
-#define		HERMES_RID_CNF_RTS_THRESH	(0xfc83)
-#define		HERMES_RID_CNF_TX_RATE_CTRL	(0xfc84)
-#define		HERMES_RID_CNF_PROMISCUOUS	(0xfc85)
-#define		HERMES_RID_CNF_KEYS		(0xfcb0)
-#define		HERMES_RID_CNF_TX_KEY		(0xfcb1)
-#define		HERMES_RID_CNF_TICKTIME		(0xfce0)
-
-#define		HERMES_RID_CNF_PRISM2_TX_KEY	(0xfc23)
-#define		HERMES_RID_CNF_PRISM2_KEY0	(0xfc24)
-#define		HERMES_RID_CNF_PRISM2_KEY1	(0xfc25)
-#define		HERMES_RID_CNF_PRISM2_KEY2	(0xfc26)
-#define		HERMES_RID_CNF_PRISM2_KEY3	(0xfc27)
-#define		HERMES_RID_CNF_SYMBOL_MANDATORY_BSSID	(0xfc21)
-#define		HERMES_RID_CNF_SYMBOL_AUTH_TYPE		(0xfc2A)
-#define		HERMES_RID_CNF_SYMBOL_BASIC_RATES	(0xfc8A)
-#define		HERMES_RID_CNF_SYMBOL_PREAMBLE		(0xfc8C)
-
-/*
- * Information RIDs
- */
-#define		HERMES_RID_CHANNEL_LIST		(0xfd10)
-#define		HERMES_RID_STAIDENTITY		(0xfd20)
-#define		HERMES_RID_CURRENT_SSID		(0xfd41)
-#define		HERMES_RID_CURRENT_BSSID	(0xfd42)
-#define		HERMES_RID_COMMSQUALITY		(0xfd43)
-#define 	HERMES_RID_CURRENT_TX_RATE	(0xfd44)
-#define 	HERMES_RID_SHORT_RETRY_LIMIT	(0xfd48)
-#define 	HERMES_RID_LONG_RETRY_LIMIT	(0xfd49)
-#define 	HERMES_RID_MAX_TX_LIFETIME	(0xfd4A)
-#define		HERMES_RID_WEP_AVAIL		(0xfd4f)
-#define		HERMES_RID_CURRENT_CHANNEL	(0xfdc1)
-#define		HERMES_RID_DATARATES		(0xfdc6)
-#define		HERMES_RID_SYMBOL_PRIMARY_VER	(0xfd03)
-#define		HERMES_RID_SYMBOL_SECONDARY_VER	(0xfd21)
-#define		HERMES_RID_SYMBOL_KEY_LENGTH	(0xfc2B)
-
-/*
- * Frame structures and constants
- */
-
-typedef struct hermes_frame_desc {
-	/* Hermes - i.e. little-endian byte-order */
-	uint16_t status; /* 0x0 */
-	uint16_t res1, res2; /* 0x2, 0x4 */
-	uint16_t q_info; /* 0x6 */
-	uint16_t res3, res4; /* 0x8, 0xA */
-	uint16_t tx_ctl; /* 0xC */
-} __attribute__ ((packed)) hermes_frame_desc_t;
-
-#define		HERMES_RXSTAT_ERR		(0x0003)
-#define		HERMES_RXSTAT_MACPORT		(0x0700)
-#define		HERMES_RXSTAT_MSGTYPE		(0xE000)
-
-#define		HERMES_RXSTAT_BADCRC		(0x0001)
-#define		HERMES_RXSTAT_UNDECRYPTABLE	(0x0002)
-
-/* RFC-1042 encoded frame */
-#define		HERMES_RXSTAT_1042		(0x2000)
-/* Bridge-tunnel encoded frame */
-#define		HERMES_RXSTAT_TUNNEL		(0x4000)
-/* Wavelan-II Management Protocol frame */
-#define		HERMES_RXSTAT_WMP		(0x6000)
-
-#ifdef __KERNEL__
-
-/* Basic control structure */
-typedef struct hermes {
-	uint iobase;
-
-	uint16_t inten; /* Which interrupts should be enabled? */
-} hermes_t;
-
-typedef struct hermes_response {
-	uint16_t status, resp0, resp1, resp2;
-} hermes_response_t;
-
-/* Firmware information structure */
-typedef struct hermes_identity {
-	uint16_t id, vendor, major, minor;
-} __attribute__ ((packed)) hermes_identity_t;
-
-/* "ID" structure - used for ESSID and station nickname */
-typedef struct hermes_id {
-	uint16_t len;
-	uint16_t val[16];
-} __attribute__ ((packed)) hermes_id_t;
-
-typedef struct hermes_commsqual {
-	uint16_t qual, signal, noise;
-} __attribute__ ((packed)) hermes_commsqual_t;
-
-typedef struct hermes_multicast {
-	uint8_t addr[HERMES_MAX_MULTICAST][ETH_ALEN];
-} __attribute__ ((packed)) hermes_multicast_t;
-
-/* Register access convenience macros */
-#define hermes_read_reg(hw, off) (inw((hw)->iobase + (off)))
-#define hermes_write_reg(hw, off, val) (outw_p((val), (hw)->iobase + (off)))
-
-#define hermes_read_regn(hw, name) (hermes_read_reg((hw), HERMES_##name))
-#define hermes_write_regn(hw, name, val) (hermes_write_reg((hw), HERMES_##name, (val)))
-
-/* Note that for the next two, the count is in 16-bit words, not bytes */
-#define hermes_read_data(hw, off, buf, count) (insw((hw)->iobase + (off), (buf), (count)))
-#define hermes_write_data(hw, off, buf, count) (outsw((hw)->iobase + (off), (buf), (count)))
-
-/* Function prototypes */
-void hermes_struct_init(hermes_t *hw, ushort io);
-int hermes_reset(hermes_t *hw);
-int hermes_docmd_wait(hermes_t *hw, uint16_t cmd, uint16_t parm0, hermes_response_t *resp);
-int hermes_allocate(hermes_t *hw, uint16_t size, uint16_t *fid);
-
-
-int hermes_bap_pread(hermes_t *hw, int bap, void *buf, uint16_t len,
-		       uint16_t id, uint16_t offset);
-int hermes_bap_pwrite(hermes_t *hw, int bap, const void *buf, uint16_t len,
-			uint16_t id, uint16_t offset);
-int hermes_read_ltv(hermes_t *hw, int bap, uint16_t rid, int buflen,
-		    uint16_t *length, void *buf);
-int hermes_write_ltv(hermes_t *hw, int bap, uint16_t rid,
-		      uint16_t length, const void *value);
-
-/* Inline functions */
-
-static inline int hermes_present(hermes_t *hw)
-{
-	return hermes_read_regn(hw, SWSUPPORT0) == HERMES_MAGIC;
-}
-
-static inline void hermes_enable_interrupt(hermes_t *hw, uint16_t events)
-{
-	hw->inten |= events;
-	hermes_write_regn(hw, INTEN, hw->inten);
-}
-
-static inline void hermes_set_irqmask(hermes_t *hw, uint16_t events)
-{
-	hw->inten = events;
-	hermes_write_regn(hw, INTEN, events);
-}
-
-static inline int hermes_enable_port(hermes_t *hw, int port)
-{
-	hermes_response_t resp;
-
-	return hermes_docmd_wait(hw, HERMES_CMD_ENABLE | (port << 8),
-				 0, &resp);
-}
-
-static inline int hermes_disable_port(hermes_t *hw, int port)
-{
-	hermes_response_t resp;
-
-	return hermes_docmd_wait(hw, HERMES_CMD_ENABLE | (port << 8), 
-				 0, &resp);
-}
-
-#define HERMES_BYTES_TO_RECLEN(n) ( ((n) % 2) ? (((n)+1)/2)+1 : ((n)/2)+1 )
-#define HERMES_RECLEN_TO_BYTES(n) ( ((n)-1) * 2 )
-
-#define HERMES_READ_RECORD(hw, bap, rid, buf) \
-	(hermes_read_ltv((hw),(bap),(rid), sizeof(*buf), NULL, (buf)))
-#define HERMES_WRITE_RECORD(hw, bap, rid, buf) \
-	(hermes_write_ltv((hw),(bap),(rid),HERMES_BYTES_TO_RECLEN(sizeof(*buf)),(buf)))
-
-static inline int hermes_read_wordrec(hermes_t *hw, int bap, uint16_t rid, uint16_t *word)
-{
-	uint16_t rec;
-	int err;
-
-	err = HERMES_READ_RECORD(hw, bap, rid, &rec);
-	*word = le16_to_cpu(rec);
-	return err;
-}
-
-static inline int hermes_write_wordrec(hermes_t *hw, int bap, uint16_t rid, uint16_t word)
-{
-	uint16_t rec = cpu_to_le16(word);
-	return HERMES_WRITE_RECORD(hw, bap, rid, &rec);
-}
-
-static inline int hermes_read_staidentity(hermes_t *hw, int bap, hermes_identity_t *buf)
-{
-	int err;
-
-	err = HERMES_READ_RECORD(hw, bap, HERMES_RID_STAIDENTITY, buf);
-	if (err)
-		return err;
-
-	le16_to_cpus(&buf->id);
-	le16_to_cpus(&buf->vendor);
-	le16_to_cpus(&buf->major);
-	le16_to_cpus(&buf->minor);
-	
-	return 0;
-}
-
-static inline int hermes_read_commsqual(hermes_t *hw, int bap, hermes_commsqual_t *buf)
-{
-	int err;
-
-	err = HERMES_READ_RECORD(hw, bap, HERMES_RID_COMMSQUALITY, buf);
-	if (err)
-		return err;
-
-	le16_to_cpus(&buf->qual);
-	le16_to_cpus(&buf->signal);
-	le16_to_cpus(&buf->noise);
-	
-	return 0;
-}
-
-#else /* ! __KERNEL__ */
-
-/* These are provided for the benefit of userspace drivers and testing programs
-   which use ioperm() or iopl() */
-
-#define hermes_read_reg(base, off) (inw((base) + (off)))
-#define hermes_write_reg(base, off, val) (outw((val), (base) + (off)))
-
-#define hermes_read_regn(base, name) (hermes_read_reg((base), HERMES_##name))
-#define hermes_write_regn(base, name, val) (hermes_write_reg((base), HERMES_##name, (val)))
-
-/* Note that for the next two, the count is in 16-bit words, not bytes */
-#define hermes_read_data(base, off, buf, count) (insw((base) + (off), (buf), (count)))
-#define hermes_write_data(base, off, buf, count) (outsw((base) + (off), (buf), (count)))
-
-#endif /* ! __KERNEL__ */
-
-#endif  /* _HERMES_H */

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)