patch-2.4.5 linux/arch/ppc/boot/mbx/qspan_pci.c

• Lines: 272
• Date: Thu May 24 15:02:06 2001
• Orig file: v2.4.4/linux/arch/ppc/boot/mbx/qspan_pci.c
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.4.4/linux/arch/ppc/boot/mbx/qspan_pci.c linux/arch/ppc/boot/mbx/qspan_pci.c
@@ -0,0 +1,271 @@
+/*
+ * BK Id: SCCS/s.qspan_pci.c 1.6 05/18/01 15:17:06 cort
+ */
+/*
+ * LinuxPPC arch/ppc/kernel/qspan_pci.c   Dan Malek (dmalek@jlc.net)
+ *
+ * QSpan Motorola bus to PCI bridge.  The config address register
+ * is located 0x500 from the base of the bridge control/status registers.
+ * The data register is located at 0x504.
+ * This is a two step operation.  First, the address register is written,
+ * then the data register is read/written as required.
+ * I don't know what to do about interrupts (yet).
+ */
+
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <asm/mpc8xx.h>
+
+/*
+ * When reading the configuration space, if something does not respond
+ * the bus times out and we get a machine check interrupt.  So, the
+ * good ol' exception tables come to mind to trap it and return some
+ * value.
+ *
+ * On an error we just return a -1, since that is what the caller wants
+ * returned if nothing is present.  I copied this from __get_user_asm,
+ * with the only difference of returning -1 instead of EFAULT.
+ * There is an associated hack in the machine check trap code.
+ *
+ * The QSPAN is also a big endian device, that is it makes the PCI
+ * look big endian to us.  This presents a problem for the Linux PCI
+ * functions, which assume little endian.  For example, we see the
+ * first 32-bit word like this:
+ *	------------------------
+ *	| Device ID | Vendor ID |
+ *	------------------------
+ * If we read/write as a double word, that's OK.  But in our world,
+ * when read as a word, device ID is at location 0, not location 2 as
+ * the little endian PCI would believe.  We have to switch bits in
+ * the PCI addresses given to us to get the data to/from the correct
+ * byte lanes.
+ *
+ * The QSPAN only supports 4 bits of "slot" in the dev_fn instead of 5.
+ * It always forces the MS bit to zero.  Therefore, dev_fn values
+ * greater than 128 are returned as "no device found" errors.
+ *
+ * The QSPAN can only perform long word (32-bit) configuration cycles.
+ * The "offset" must have the two LS bits set to zero.  Read operations
+ * require we read the entire word and then sort out what should be
+ * returned.  Write operations other than long word require that we
+ * read the long word, update the proper word or byte, then write the
+ * entire long word back.
+ *
+ * PCI Bridge hack.  We assume (correctly) that bus 0 is the primary
+ * PCI bus from the QSPAN.  If we are called with a bus number other
+ * than zero, we create a Type 1 configuration access that a downstream
+ * PCI bridge will interpret.
+ */
+
+#define __get_pci_config(x, addr, op)		\
+	__asm__ __volatile__(				\
+		"1:	"op" %0,0(%1)\n"		\
+		"	eieio\n"			\
+		"2:\n"					\
+		".section .fixup,\"ax\"\n"		\
+		"3:	li %0,-1\n"			\
+		"	b 2b\n"				\
+		".section __ex_table,\"a\"\n"		\
+		"	.align 2\n"			\
+		"	.long 1b,3b\n"			\
+		".text"					\
+		: "=r"(x) : "r"(addr))
+
+#define QS_CONFIG_ADDR	((volatile uint *)(PCI_CSR_ADDR + 0x500))
+#define QS_CONFIG_DATA	((volatile uint *)(PCI_CSR_ADDR + 0x504))
+
+#define mk_config_addr(bus, dev, offset) \
+	(((bus)<<16) | ((dev)<<8) | (offset & 0xfc))
+
+#define mk_config_type1(bus, dev, offset) \
+	mk_config_addr(bus, dev, offset) | 1;
+
+/* Initialize the QSpan device registers after power up.
+*/
+qspan_init()
+{
+	uint	*qptr;
+
+
+
+	qptr = (uint *)PCI_CSR_ADDR;
+
+	/* PCI Configuration/status.  Upper bits written to clear
+	 * pending interrupt or status.  Lower bits enable QSPAN as
+	 * PCI master, enable memory and I/O cycles, and enable PCI
+	 * parity error checking.
+	 * IMPORTANT:  The last two bits of this word enable PCI
+	 * master cycles into the QBus.  The QSpan is broken and can't
+	 * meet the timing specs of the PQ bus for this to work.  Therefore,
+	 * if you don't have external bus arbitration, you can't use
+	 * this function.
+	 */
+#ifdef EXTERNAL_PQ_ARB
+	qptr[1] = 0xf9000147;
+#else
+	qptr[1] = 0xf9000144;
+#endif
+
+	/* PCI Misc configuration.  Set PCI latency timer resolution
+	 * of 8 cycles, set cache size to 4 x 32.
+	 */
+	qptr[3] = 0;
+
+	/* Set up PCI Target address mapping.  Enable, Posted writes,
+	 * 2Gbyte space (processor memory controller determines actual size).
+	 */
+	qptr[64] = 0x8f000080;
+
+	/* Map processor 0x80000000 to PCI 0x00000000.
+	 * Processor address bit 1 determines I/O type access (0x80000000)
+	 * or memory type access (0xc0000000).
+	 */
+	qptr[65] = 0x80000000;
+
+	/* Enable error logging and clear any pending error status.
+	*/
+	qptr[80] = 0x90000000;
+
+	qptr[512] = 0x000c0003;
+
+	/* Set up Qbus slave image.
+	*/
+	qptr[960] = 0x01000000;
+	qptr[961] = 0x000000d1;
+	qptr[964] = 0x00000000;
+	qptr[965] = 0x000000d1;
+
+}
+
+/* Functions to support PCI bios-like features to read/write configuration
+ * space.  If the function fails for any reason, a -1 (0xffffffff) value
+ * must be returned.
+ */
+#define DEVICE_NOT_FOUND	(-1)
+#define SUCCESSFUL		0
+
+int qs_pci_read_config_byte(unsigned char bus, unsigned char dev_fn,
+				  unsigned char offset, unsigned char *val)
+{
+	uint	temp;
+	u_char	*cp;
+
+	if ((bus > 7) || (dev_fn > 127)) {
+		*val = 0xff;
+		return DEVICE_NOT_FOUND;
+	}
+
+	if (bus == 0)
+		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);
+	else
+		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);
+	__get_pci_config(temp, QS_CONFIG_DATA, "lwz");
+
+	offset ^= 0x03;
+	cp = ((u_char *)&temp) + (offset & 0x03);
+	*val = *cp;
+	return SUCCESSFUL;
+}
+
+int qs_pci_read_config_word(unsigned char bus, unsigned char dev_fn,
+				  unsigned char offset, unsigned short *val)
+{
+	uint	temp;
+	ushort	*sp;
+
+	if ((bus > 7) || (dev_fn > 127)) {
+		*val = 0xffff;
+		return DEVICE_NOT_FOUND;
+	}
+
+	if (bus == 0)
+		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);
+	else
+		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);
+	__get_pci_config(temp, QS_CONFIG_DATA, "lwz");
+	offset ^= 0x02;
+
+	sp = ((ushort *)&temp) + ((offset >> 1) & 1);
+	*val = *sp;
+	return SUCCESSFUL;
+}
+
+int qs_pci_read_config_dword(unsigned char bus, unsigned char dev_fn,
+				   unsigned char offset, unsigned int *val)
+{
+	if ((bus > 7) || (dev_fn > 127)) {
+		*val = 0xffffffff;
+		return DEVICE_NOT_FOUND;
+	}
+	if (bus == 0)
+		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);
+	else
+		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);
+	__get_pci_config(*val, QS_CONFIG_DATA, "lwz");
+	return SUCCESSFUL;
+}
+
+int qs_pci_write_config_byte(unsigned char bus, unsigned char dev_fn,
+				   unsigned char offset, unsigned char val)
+{
+	uint	temp;
+	u_char	*cp;
+
+	if ((bus > 7) || (dev_fn > 127))
+		return DEVICE_NOT_FOUND;
+
+	qs_pci_read_config_dword(bus, dev_fn, offset, &temp);
+
+	offset ^= 0x03;
+	cp = ((u_char *)&temp) + (offset & 0x03);
+	*cp = val;
+
+	if (bus == 0)
+		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);
+	else
+		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);
+	*QS_CONFIG_DATA = temp;
+
+	return SUCCESSFUL;
+}
+
+int qs_pci_write_config_word(unsigned char bus, unsigned char dev_fn,
+				   unsigned char offset, unsigned short val)
+{
+	uint	temp;
+	ushort	*sp;
+
+	if ((bus > 7) || (dev_fn > 127))
+		return DEVICE_NOT_FOUND;
+
+	qs_pci_read_config_dword(bus, dev_fn, offset, &temp);
+
+	offset ^= 0x02;
+	sp = ((ushort *)&temp) + ((offset >> 1) & 1);
+	*sp = val;
+
+	if (bus == 0)
+		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);
+	else
+		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);
+	*QS_CONFIG_DATA = temp;
+
+	return SUCCESSFUL;
+}
+
+int qs_pci_write_config_dword(unsigned char bus, unsigned char dev_fn,
+				    unsigned char offset, unsigned int val)
+{
+	if ((bus > 7) || (dev_fn > 127))
+		return DEVICE_NOT_FOUND;
+
+	if (bus == 0)
+		*QS_CONFIG_ADDR = mk_config_addr(bus, dev_fn, offset);
+	else
+		*QS_CONFIG_ADDR = mk_config_type1(bus, dev_fn, offset);
+	*(unsigned int *)QS_CONFIG_DATA = val;
+
+	return SUCCESSFUL;
+}
+