patch-2.4.22 linux-2.4.22/include/asm-ppc/serial.h
Next file: linux-2.4.22/include/asm-ppc/shmbuf.h
Previous file: linux-2.4.22/include/asm-ppc/sembuf.h
Back to the patch index
Back to the overall index
- Lines: 137
- Date:
2003-08-25 04:44:44.000000000 -0700
- Orig file:
linux-2.4.21/include/asm-ppc/serial.h
- Orig date:
2003-06-13 07:51:38.000000000 -0700
diff -urN linux-2.4.21/include/asm-ppc/serial.h linux-2.4.22/include/asm-ppc/serial.h
@@ -14,128 +14,21 @@
#include <platforms/lopec_serial.h>
#elif defined(CONFIG_SPRUCE)
#include <platforms/spruce.h>
-#elif defined(CONFIG_4xx)
-#include <asm/ppc4xx_serial.h>
+#elif defined(CONFIG_40x)
+#include <asm/ibm4xx.h>
#else
/*
- * This assumes you have a 1.8432 MHz clock for your UART.
- *
- * It'd be nice if someone built a serial card with a 24.576 MHz
- * clock, since the 16550A is capable of handling a top speed of 1.5
- * megabits/second; but this requires the faster clock.
+ * XXX Assume for now it has PC-style ISA serial ports.
+ * This is true for PReP and CHRP at least.
*/
-#define BASE_BAUD ( 1843200 / 16 )
+#include <asm/pc_serial.h>
+#include <asm/processor.h>
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define RS_TABLE_SIZE 64
-#else
-#define RS_TABLE_SIZE 4
-#endif
-
-/* Standard COM flags (except for COM4, because of the 8514 problem) */
-#ifdef CONFIG_SERIAL_DETECT_IRQ
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ)
-#define STD_COM4_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_AUTO_IRQ)
-#else
-#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
-#define STD_COM4_FLAGS ASYNC_BOOT_AUTOCONF
-#endif
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define FOURPORT_FLAGS ASYNC_FOURPORT
-#define ACCENT_FLAGS 0
-#define BOCA_FLAGS 0
-#define HUB6_FLAGS 0
-#endif
-
-/*
- * The following define the access methods for the HUB6 card. All
- * access is through two ports for all 24 possible chips. The card is
- * selected through the high 2 bits, the port on that card with the
- * "middle" 3 bits, and the register on that port with the bottom
- * 3 bits.
- *
- * While the access port and interrupt is configurable, the default
- * port locations are 0x302 for the port control register, and 0x303
- * for the data read/write register. Normally, the interrupt is at irq3
- * but can be anything from 3 to 7 inclusive. Note that using 3 will
- * require disabling com2.
- */
-
-#define C_P(card,port) (((card)<<6|(port)<<3) + 1)
-
-#define STD_SERIAL_PORT_DEFNS \
- /* UART CLK PORT IRQ FLAGS */ \
- { 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS }, /* ttyS0 */ \
- { 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }, /* ttyS1 */ \
- { 0, BASE_BAUD, 0x3E8, 4, STD_COM_FLAGS }, /* ttyS2 */ \
- { 0, BASE_BAUD, 0x2E8, 3, STD_COM4_FLAGS }, /* ttyS3 */
-
-
-#ifdef CONFIG_SERIAL_MANY_PORTS
-#define EXTRA_SERIAL_PORT_DEFNS \
- { 0, BASE_BAUD, 0x1A0, 9, FOURPORT_FLAGS }, /* ttyS4 */ \
- { 0, BASE_BAUD, 0x1A8, 9, FOURPORT_FLAGS }, /* ttyS5 */ \
- { 0, BASE_BAUD, 0x1B0, 9, FOURPORT_FLAGS }, /* ttyS6 */ \
- { 0, BASE_BAUD, 0x1B8, 9, FOURPORT_FLAGS }, /* ttyS7 */ \
- { 0, BASE_BAUD, 0x2A0, 5, FOURPORT_FLAGS }, /* ttyS8 */ \
- { 0, BASE_BAUD, 0x2A8, 5, FOURPORT_FLAGS }, /* ttyS9 */ \
- { 0, BASE_BAUD, 0x2B0, 5, FOURPORT_FLAGS }, /* ttyS10 */ \
- { 0, BASE_BAUD, 0x2B8, 5, FOURPORT_FLAGS }, /* ttyS11 */ \
- { 0, BASE_BAUD, 0x330, 4, ACCENT_FLAGS }, /* ttyS12 */ \
- { 0, BASE_BAUD, 0x338, 4, ACCENT_FLAGS }, /* ttyS13 */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS14 (spare) */ \
- { 0, BASE_BAUD, 0x000, 0, 0 }, /* ttyS15 (spare) */ \
- { 0, BASE_BAUD, 0x100, 12, BOCA_FLAGS }, /* ttyS16 */ \
- { 0, BASE_BAUD, 0x108, 12, BOCA_FLAGS }, /* ttyS17 */ \
- { 0, BASE_BAUD, 0x110, 12, BOCA_FLAGS }, /* ttyS18 */ \
- { 0, BASE_BAUD, 0x118, 12, BOCA_FLAGS }, /* ttyS19 */ \
- { 0, BASE_BAUD, 0x120, 12, BOCA_FLAGS }, /* ttyS20 */ \
- { 0, BASE_BAUD, 0x128, 12, BOCA_FLAGS }, /* ttyS21 */ \
- { 0, BASE_BAUD, 0x130, 12, BOCA_FLAGS }, /* ttyS22 */ \
- { 0, BASE_BAUD, 0x138, 12, BOCA_FLAGS }, /* ttyS23 */ \
- { 0, BASE_BAUD, 0x140, 12, BOCA_FLAGS }, /* ttyS24 */ \
- { 0, BASE_BAUD, 0x148, 12, BOCA_FLAGS }, /* ttyS25 */ \
- { 0, BASE_BAUD, 0x150, 12, BOCA_FLAGS }, /* ttyS26 */ \
- { 0, BASE_BAUD, 0x158, 12, BOCA_FLAGS }, /* ttyS27 */ \
- { 0, BASE_BAUD, 0x160, 12, BOCA_FLAGS }, /* ttyS28 */ \
- { 0, BASE_BAUD, 0x168, 12, BOCA_FLAGS }, /* ttyS29 */ \
- { 0, BASE_BAUD, 0x170, 12, BOCA_FLAGS }, /* ttyS30 */ \
- { 0, BASE_BAUD, 0x178, 12, BOCA_FLAGS }, /* ttyS31 */
-#else
-#define EXTRA_SERIAL_PORT_DEFNS
-#endif
-
-/* You can have up to four HUB6's in the system, but I've only
- * included two cards here for a total of twelve ports.
- */
-#if (defined(CONFIG_HUB6) && defined(CONFIG_SERIAL_MANY_PORTS))
-#define HUB6_SERIAL_PORT_DFNS \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,0) }, /* ttyS32 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,1) }, /* ttyS33 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,2) }, /* ttyS34 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,3) }, /* ttyS35 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,4) }, /* ttyS36 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(0,5) }, /* ttyS37 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,0) }, /* ttyS38 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,1) }, /* ttyS39 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,2) }, /* ttyS40 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,3) }, /* ttyS41 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,4) }, /* ttyS42 */ \
- { 0, BASE_BAUD, 0x302, 3, HUB6_FLAGS, C_P(1,5) }, /* ttyS43 */
-#else
-#define HUB6_SERIAL_PORT_DFNS
+#if defined(CONFIG_MAC_SERIAL)
+#define SERIAL_DEV_OFFSET ((_machine == _MACH_prep || _machine == _MACH_chrp) ? 0 : 2)
#endif
-#define MCA_SERIAL_PORT_DFNS
-
-#define SERIAL_PORT_DFNS \
- STD_SERIAL_PORT_DEFNS \
- EXTRA_SERIAL_PORT_DEFNS \
- HUB6_SERIAL_PORT_DFNS \
- MCA_SERIAL_PORT_DFNS
-
#endif /* !CONFIG_GEMINI and others */
#endif /* __ASM_SERIAL_H__ */
#endif /* __KERNEL__ */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)