patch-2.4.22 linux-2.4.22/include/asm-ppc/ppc4xx.h
Next file: linux-2.4.22/include/asm-ppc/ppc4xx_pic.h
Previous file: linux-2.4.22/include/asm-ppc/posix_types.h
Back to the patch index
Back to the overall index
- Lines: 283
- Date:
1969-12-31 16:00:00.000000000 -0800
- Orig file:
linux-2.4.21/include/asm-ppc/ppc4xx.h
- Orig date:
2003-06-13 07:51:38.000000000 -0700
diff -urN linux-2.4.21/include/asm-ppc/ppc4xx.h linux-2.4.22/include/asm-ppc/ppc4xx.h
@@ -1,282 +0,0 @@
-/*
- *
- * Copyright (c) 1999 Grant Erickson <grant@lcse.umn.edu>
- *
- * Module name: ppc4xx.h
- *
- * Description:
- * A generic include file which pulls in appropriate include files
- * for specific board types based on configuration settings.
- *
- */
-
-#ifdef __KERNEL__
-#ifndef __PPC4XX_H__
-#define __PPC4XX_H__
-
-#include <linux/config.h>
-
-#ifndef __ASSEMBLY__
-
-#if defined(CONFIG_OAK)
-#include <platforms/oak.h>
-#endif
-
-#if defined(CONFIG_WALNUT)
-#include <platforms/walnut.h>
-#endif
-
-/* IO_BASE is for PCI I/O.
- * ISA not supported, just here to resolve copilation.
- */
-
-#ifndef _IO_BASE
-#define _IO_BASE 0xe8000000 /* The PCI address window */
-#define _ISA_MEM_BASE 0
-#define PCI_DRAM_OFFSET 0
-#endif
-
-/*
- * The "residual" board information structure the boot loader passes
- * into the kernel.
- */
-extern unsigned char __res[];
-
-/* I don't know if this is general to 4xx, or unique to a specific
- * processor or board. In any case it is easy to move.
- */
-#define PPC4xx_PCI_IO_ADDR ((uint)0xe8000000)
-#define PPC4xx_PCI_IO_SIZE ((uint)64*1024)
-#define PPC4xx_PCI_CFG_ADDR ((uint)0xeec00000)
-#define PPC4xx_PCI_CFG_SIZE ((uint)4*1024)
-#define PPC4xx_PCI_LCFG_ADDR ((uint)0xef400000)
-#define PPC4xx_PCI_LCFG_SIZE ((uint)4*1024)
-#define PPC4xx_ONB_IO_ADDR ((uint)0xef600000)
-#define PPC4xx_ONB_IO_SIZE ((uint)4*1024)
-
-#endif /* __ASSEMBLY__ */
-
-/* Device Control Registers unique to 4xx */
-
-#define DCRN_BEAR 0x090 /* Bus Error Address Register */
-#define DCRN_BESR 0x091 /* Bus Error Syndrome Register */
-#define BESR_DSES 0x80000000 /* Data-Side Error Status */
-#define BESR_DMES 0x40000000 /* DMA Error Status */
-#define BESR_RWS 0x20000000 /* Read/Write Status */
-#define BESR_ETMASK 0x1C000000 /* Error Type */
-#define ET_PROT 0
-#define ET_PARITY 1
-#define ET_NCFG 2
-#define ET_BUSERR 4
-#define ET_BUSTO 6
-#define DCRN_CHCR0 0x0B1 /* Chip Control Register 1 */
-#define DCRN_CHCR1 0x0B2 /* Chip Control Register 2 */
-#define DCRN_CHPSR 0x0B4 /* Chip Pin Strapping */
-#define DCRN_CPMER 0x0B9 /* CPM Enable */
-#define DCRN_CPMFR 0x0BA /* CPM Force */
-#define CPM_IIC 0x80000000 /* IIC interface */
-#define CPM_PCI 0x40000000 /* PCI bridge */
-#define CPM_CPU 0x20000000 /* processor core */
-#define CPM_DMA 0x10000000 /* DMA controller */
-#define CPM_BRG 0x08000000 /* PLB to OPB bridge */
-#define CPM_DCP 0x04000000 /* CodePack */
-#define CPM_EBC 0x02000000 /* ROM/SRAM peripheral controller */
-#define CPM_SDRAM 0x01000000 /* SDRAM memory controller */
-#define CPM_PLB 0x00800000 /* PLB bus arbiter */
-#define CPM_GPIO 0x00400000 /* General Purpose IO (??) */
-#define CPM_UART0 0x00200000 /* serial port 0 */
-#define CPM_UART1 0x00100000 /* serial port 1 */
-#define CPM_UIC 0x00080000 /* Universal Interrupt Controller */
-#define CPM_TMRCLK 0x00040000 /* CPU timers */
-#define CPM_EMAC_MM 0x00020000 /* on-chip ethernet MM unit */
-#define CPM_EMAC_RM 0x00010000 /* on-chip ethernet RM unit */
-#define CPM_EMAC_TM 0x00008000 /* on-chip ethernet TM unit */
-#define DCRN_CPMSR 0x0B8 /* CPM Status */
-
-#define DCRN_DMACR0 0x100 /* DMA Channel Control Register 0 */
-#define DCRN_DMACT0 0x101 /* DMA Count Register 0 */
-#define DCRN_DMADA0 0x102 /* DMA Destination Address Register 0 */
-#define DCRN_DMASA0 0x103 /* DMA Source Address Register 0 */
-#define DCRN_ASG0 0x104 /* DMA Scatter/Gather Descriptor Addr 0 */
-
-#define DCRN_DMACR1 0x108 /* DMA Channel Control Register 1 */
-#define DCRN_DMACT1 0x109 /* DMA Count Register 1 */
-#define DCRN_DMADA1 0x10A /* DMA Destination Address Register 1 */
-#define DCRN_DMASA1 0x10B /* DMA Source Address Register 1 */
-#define DCRN_ASG1 0x10C /* DMA Scatter/Gather Descriptor Addr 1 */
-
-#define DCRN_DMACR2 0x110 /* DMA Channel Control Register 2 */
-#define DCRN_DMACT2 0x111 /* DMA Count Register 2 */
-#define DCRN_DMADA2 0x112 /* DMA Destination Address Register 2 */
-#define DCRN_DMASA2 0x113 /* DMA Source Address Register 2 */
-#define DCRN_ASG2 0x114 /* DMA Scatter/Gather Descriptor Addr 2 */
-
-#define DCRN_DMACR3 0x118 /* DMA Channel Control Register 3 */
-#define DCRN_DMACT3 0x119 /* DMA Count Register 3 */
-#define DCRN_DMADA3 0x11A /* DMA Destination Address Register 3 */
-#define DCRN_DMASA3 0x11B /* DMA Source Address Register 3 */
-#define DCRN_ASG3 0x11C /* DMA Scatter/Gather Descriptor Addr 3 */
-
-#define DCRN_DMASR 0x120 /* DMA Status Register */
-#define DCRN_ASGC 0x123 /* DMA Scatter/Gather Command */
-#define DCRN_ADR 0x124 /* DMA Address Decode */
-
-#define DCRN_SLP 0x125 /* DMA Sleep Register */
-#define DCRN_POL 0x126 /* DMA Polarity Register */
-
-
-#define DCRN_EBCCFGADR 0x012 /* Peripheral Controller Address */
-#define DCRN_EBCCFGDATA 0x013 /* Peripheral Controller Data */
-#define DCRN_EXISR 0x040 /* External Interrupt Status Register */
-#define DCRN_EXIER 0x042 /* External Interrupt Enable Register */
-#define EXIER_CIE 0x80000000 /* Critical Interrupt Enable */
-#define EXIER_SRIE 0x08000000 /* Serial Port Rx Int. Enable */
-#define EXIER_STIE 0x04000000 /* Serial Port Tx Int. Enable */
-#define EXIER_JRIE 0x02000000 /* JTAG Serial Port Rx Int. Enable */
-#define EXIER_JTIE 0x01000000 /* JTAG Serial Port Tx Int. Enable */
-#define EXIER_D0IE 0x00800000 /* DMA Channel 0 Interrupt Enable */
-#define EXIER_D1IE 0x00400000 /* DMA Channel 1 Interrupt Enable */
-#define EXIER_D2IE 0x00200000 /* DMA Channel 2 Interrupt Enable */
-#define EXIER_D3IE 0x00100000 /* DMA Channel 3 Interrupt Enable */
-#define EXIER_E0IE 0x00000010 /* External Interrupt 0 Enable */
-#define EXIER_E1IE 0x00000008 /* External Interrupt 1 Enable */
-#define EXIER_E2IE 0x00000004 /* External Interrupt 2 Enable */
-#define EXIER_E3IE 0x00000002 /* External Interrupt 3 Enable */
-#define EXIER_E4IE 0x00000001 /* External Interrupt 4 Enable */
-#define DCRN_IOCR 0x0A0 /* Input/Output Configuration Register */
-#define IOCR_E0TE 0x80000000
-#define IOCR_E0LP 0x40000000
-#define IOCR_E1TE 0x20000000
-#define IOCR_E1LP 0x10000000
-#define IOCR_E2TE 0x08000000
-#define IOCR_E2LP 0x04000000
-#define IOCR_E3TE 0x02000000
-#define IOCR_E3LP 0x01000000
-#define IOCR_E4TE 0x00800000
-#define IOCR_E4LP 0x00400000
-#define IOCR_EDT 0x00080000
-#define IOCR_SOR 0x00040000
-#define IOCR_EDO 0x00008000
-#define IOCR_2XC 0x00004000
-#define IOCR_ATC 0x00002000
-#define IOCR_SPD 0x00001000
-#define IOCR_BEM 0x00000800
-#define IOCR_PTD 0x00000400
-#define IOCR_ARE 0x00000080
-#define IOCR_DRC 0x00000020
-#define IOCR_RDM(x) (((x) & 0x3) << 3)
-#define IOCR_TCS 0x00000004
-#define IOCR_SCS 0x00000002
-#define IOCR_SPC 0x00000001
-#define DCRN_KIAR 0x014 /* Decompression Controller Address */
-#define DCRN_KIDR 0x015 /* Decompression Controller Data */
-#define DCRN_MALCR 0x180 /* MAL Configuration */
-#define MALCR_MMSR 0x80000000 /* MAL Software reset */
-#define MALCR_PLBP_1 0x00400000 /* MAL reqest priority: */
-#define MALCR_PLBP_2 0x00800000 /* lowsest is 00 */
-#define MALCR_PLBP_3 0x00C00000 /* highest */
-#define MALCR_GA 0x00200000 /* Guarded Active Bit */
-#define MALCR_OA 0x00100000 /* Ordered Active Bit */
-#define MALCR_PLBLE 0x00080000 /* PLB Lock Error Bit */
-#define MALCR_PLBLT_1 0x00040000 /* PLB Latency Timer */
-#define MALCR_PLBLT_2 0x00020000
-#define MALCR_PLBLT_3 0x00010000
-#define MALCR_PLBLT_4 0x00008000
-#define MALCR_PLBLT_DEFAULT 0x00078000 /* JSP: Is this a valid default?? */
-#define MALCR_PLBB 0x00004000 /* PLB Burst Deactivation Bit */
-#define MALCR_OPBBL 0x00000080 /* OPB Lock Bit */
-#define MALCR_EOPIE 0x00000004 /* End Of Packet Interrupt Enable */
-#define MALCR_LEA 0x00000002 /* Locked Error Active */
-#define MALCR_MSD 0x00000001 /* MAL Scroll Descriptor Bit */
-#define DCRN_MALDBR 0x183 /* Debug Register */
-#define DCRN_MALESR 0x181 /* Error Status */
-#define MALESR_EVB 0x80000000 /* Error Valid Bit */
-#define MALESR_CID 0x40000000 /* Channel ID Bit for channel 0 */
-#define MALESR_DE 0x00100000 /* Descriptor Error */
-#define MALESR_OEN 0x00080000 /* OPB Non-Fullword Error */
-#define MALESR_OTE 0x00040000 /* OPB Timeout Error */
-#define MALESR_OSE 0x00020000 /* OPB Slave Error */
-#define MALESR_PEIN 0x00010000 /* PLB Bus Error Indication */
-#define MALESR_DEI 0x00000010 /* Descriptor Error Interrupt */
-#define MALESR_ONEI 0x00000008 /* OPB Non-Fullword Error Interrupt */
-#define MALESR_OTEI 0x00000004 /* OPB Timeout Error Interrupt */
-#define MALESR_OSEI 0x00000002 /* OPB Slace Error Interrupt */
-#define MALESR_PBEI 0x00000001 /* PLB Bus Error Interrupt */
-#define DCRN_MALIER 0x182 /* Interrupt Enable */
-#define MALIER_DE 0x00000010 /* Descriptor Error Interrupt Enable */
-#define MALIER_NE 0x00000008 /* OPB Non-word Transfer Int Enable */
-#define MALIER_TE 0x00000004 /* OPB Time Out Error Interrupt Enable */
-#define MALIER_OPBE 0x00000002 /* OPB Slave Error Interrupt Enable */
-#define MALIER_PLBE 0x00000001 /* PLB Error Interrupt Enable */
-#define DCRN_MALTXCARR 0x185 /* TX Channed Active Reset Register */
-#define DCRN_MALTXCASR 0x184 /* TX Channel Active Set Register */
-#define DCRN_MALTXDEIR 0x187 /* Tx Descriptor Error Interrupt */
-#define DCRN_MALTXEOBISR 0x186 /* Tx End of Buffer Interrupt Status */
-#define MALOBISR_CH0 0x80000000 /* EOB channel 1 bit */
-#define MALOBISR_CH2 0x40000000 /* EOB channel 2 bit */
-#define DCRN_MALRXCARR 0x191 /* RX Channed Active Reset Register */
-#define DCRN_MALRXCASR 0x190 /* RX Channel Active Set Register */
-#define DCRN_MALRXDEIR 0x193 /* Rx Descriptor Error Interrupt */
-#define DCRN_MALRXEOBISR 0x192 /* Rx End of Buffer Interrupt Status */
-#define DCRN_MALRXCTP0R 0x1C0 /* Channel Rx 0 Channel Table Pointer */
-#define DCRN_MALTXCTP0R 0x1A0 /* Channel Tx 0 Channel Table Pointer */
-#define DCRN_MALTXCTP1R 0x1A1 /* Channel Tx 1 Channel Table Pointer */
-#define DCRN_MALRCBS0 0x1E0 /* Channel Rx 0 Channel Buffer Size */
-#define DCRN_MEMCFGADR 0x010 /* Memory Controller Address */
-#define DCRN_MEMCFGDATA 0x011 /* Memory Controller Data */
-#define DCRN_OCMISARC 0x018 /* OCM Instr Side Addr Range Compare */
-#define DCRN_OCMISCR 0x019 /* OCM Instr Side Control */
-#define DCRN_OCMDSARC 0x01A /* OCM Data Side Addr Range Compare */
-#define DCRN_OCMDSCR 0x01B /* OCM Data Side Control */
-#define DCRN_PLB0_ACR 0x087 /* PLB Arbiter Control */
-#define DCRN_PLB0_BEAR 0x086 /* PLB Error Address */
-#define DCRN_PLB0_BESR 0x084 /* PLB Error Status */
-#define DCRN_PLLMR 0x0B0 /* PLL Mode */
-#define DCRN_POB0_BEAR 0x0A2 /* PLB to OPB Error Address */
-#define DCRN_POB0_BESR0 0x0A0 /* PLB to OPB Error Status Register 1 */
-#define DCRN_POB0_BESR1 0x0A4 /* PLB to OPB Error Status Register 1 */
-#define DCRN_UICCR 0x0C3 /* UIC Critical */
-#define DCRN_UICER 0x0C2 /* UIC Enable */
-#define DCRN_UICPR 0x0C4 /* UIC Polarity */
-#define DCRN_UICSR 0x0C0 /* UIC Status */
-#define DCRN_UICTR 0x0C5 /* UIC Triggering */
-#define DCRN_UICMSR 0x0C6 /* UIC Masked Status */
-#define DCRN_UICVR 0x0C7 /* UIC Vector */
-#define DCRN_UICVCR 0x0C8 /* UIC Vector Configuration */
-#define UIC_U0 0x80000000 /* UART0 */
-#define UIC_U1 0x40000000 /* UART1 */
-#define UIC_IIC 0x20000000 /* IIC */
-#define UIC_EM 0x10000000 /* External Master */
-#define UIC_PCI 0x08000000 /* PCI */
-#define UIC_D0 0x04000000 /* DMA Channel 0 */
-#define UIC_D1 0x02000000 /* DMA Channel 1 */
-#define UIC_D2 0x01000000 /* DMA Channel 2 */
-#define UIC_D3 0x00800000 /* DMA Channel 3 */
-#define UIC_EW 0x00400000 /* Ethernet Wake-up */
-#define UIC_MS 0x00200000 /* MAL SERR */
-#define UIC_MTE 0x00100000 /* MAL TX EOB */
-#define UIC_MRE 0x00080000 /* MAL RX EOB */
-#define UIC_MTD 0x00040000 /* MAL TX DE */
-#define UIC_MRD 0x00020000 /* MAL RX DE */
-#define UIC_E 0x00010000 /* Ethernet */
-#define UIC_EPS 0x00008000 /* External PCI SERR */
-#define UIC_EC 0x00004000 /* ECC Correctable Error */
-#define UIC_PPM 0x00002000 /* PCI Power Management */
-/*
-** 0x00001000 reserved
-** 0x00000800 reserved
-** 0x00000400 reserved
-** 0x00000200 reserved
-** 0x00000100 reserved
-** 0x00000080 reserved
-*/
-#define UIC_EIR0 0x00000040 /* External IRQ 0 */
-#define UIC_EIR1 0x00000020 /* External IRQ 0 */
-#define UIC_EIR2 0x00000010 /* External IRQ 0 */
-#define UIC_EIR3 0x00000008 /* External IRQ 0 */
-#define UIC_EIR4 0x00000004 /* External IRQ 0 */
-#define UIC_EIR5 0x00000002 /* External IRQ 0 */
-#define UIC_EIR6 0x00000001 /* External IRQ 0 */
-
-#endif /* __PPC4XX_H__ */
-#endif /* __KERNEL__ */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)