patch-2.4.21 linux-2.4.21/drivers/net/tulip/ChangeLog
Next file: linux-2.4.21/drivers/net/tulip/eeprom.c
Previous file: linux-2.4.21/drivers/net/tulip/21142.c
Back to the patch index
Back to the overall index
- Lines: 391
- Date:
2003-06-13 07:51:35.000000000 -0700
- Orig file:
linux-2.4.20/drivers/net/tulip/ChangeLog
- Orig date:
2002-11-28 15:53:14.000000000 -0800
diff -urN linux-2.4.20/drivers/net/tulip/ChangeLog linux-2.4.21/drivers/net/tulip/ChangeLog
@@ -14,12 +14,12 @@
* 21142.c (t21142_lnk_change): Revert earlier patch
to always reset phy; only conditionally do so now.
-2002-05-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2002-05-03 Jeff Garzik <jgarzik@pobox.com>
* tulip_core (tulip_pci_tbl): Add new "comet"
pci id. Contributed by Ohta Kyuma.
-2002-03-07 Jeff Garzik <jgarzik@mandrakesoft.com>
+2002-03-07 Jeff Garzik <jgarzik@pobox.com>
* tulip_core (tulip_mwi_config): Use new PCI API functions
for enabling and disabled Memory-Write-Invalidate
@@ -98,30 +98,30 @@
Clear status for in-progress Tx's, and count
Tx errors for all packets being released.
-2001-06-16 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-06-16 Jeff Garzik <jgarzik@pobox.com>
* tulip.h, tulip_core.c:
Integrate MMIO support from devel branch, but default
it to off for stable kernel and driver series.
-2001-06-16 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-06-16 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (tulip_init_one):
Free descriptor rings on error.
-2001-06-16 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-06-16 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (tulip_mwi_config, tulip_init_one):
Large update to csr0 bus configuration code. This is not stable
yet, so it is only conditionally enabled, via CONFIG_TULIP_MWI.
-2001-06-16 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-06-16 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c:
Initialize timer in tulip_init_one and tulip_down,
not in tulip_up.
-2001-06-14 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-06-14 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c:
- Update tulip_suspend, tulip_resume for new PCI PM API.
@@ -138,14 +138,14 @@
* tulip_core (set_rx_mode): Do not use set_bit
on an integer variable. Also fix endianness issue.
-2001-06-04 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-06-04 Jeff Garzik <jgarzik@pobox.com>
* interrupt.c:
Simplify rx processing when CONFIG_NET_HW_FLOWCONTROL is
active, and in the process fix a bug where flow control
and low load caused rx not to be acknowledged properly.
-2001-06-01 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-06-01 Jeff Garzik <jgarzik@pobox.com>
* tulip.h:
- Remove tulip_outl_csr helper, redundant.
@@ -165,7 +165,7 @@
convert tabs to spaces.
- Move tp->stats.rx_missed_errors update outside the ifdef.
-2001-05-18 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-18 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: Added ethtool support.
ETHTOOL_GDRVINFO ioctl only, for now.
@@ -184,22 +184,22 @@
* tulip_refill_rx prototype added to tulip.h
-2001-05-13 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-13 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: Remove HAS_PCI_MWI flag from Comet, untested.
-2001-05-12 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-12 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c, tulip.h: Remove Conexant PCI id, no chip
docs are available to fix problems with support.
-2001-05-12 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-12 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (tulip_init_one): Do not call
unregister_netdev in error cleanup. Remnant of old
usage of init_etherdev.
-2001-05-12 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-12 Jeff Garzik <jgarzik@pobox.com>
* media.c (tulip_find_mii): Simple write the updated BMCR
twice, as it seems the best thing to do for both broken and
@@ -210,36 +210,36 @@
Fill in tp->advertising for all cases.
Just to be safe, clear all unwanted bits.
-2001-05-12 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-12 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (private_ioctl): Fill in tp->advertising
when advertising value is changed by the user.
-2001-05-12 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-12 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: Mark Comet chips as needed the updated MWI
csr0 configuration.
-2001-05-12 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-12 Jeff Garzik <jgarzik@pobox.com>
* media.c, tulip_core.c: Move MII scan into
from inlined inside tulip_init_one to new function
tulip_find_mii in media.c.
-2001-05-12 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-12 Jeff Garzik <jgarzik@pobox.com>
* media.c (tulip_check_duplex):
Only restart Rx/Tx engines if they are active
(and csr6 changes)
-2001-05-12 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-12 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (tulip_mwi_config):
Clamp values read from PCI cache line size register to
values acceptable to tulip chip. Done for safety and
-almost- certainly unneeded.
-2001-05-11 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-11 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (tulip_init_one):
Instead of unconditionally enabling autonegotiation, disable
@@ -253,7 +253,7 @@
to BMCR twice, to avoid setting unnecessarily changing
phy settings.
-2001-05-11 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-11 Jeff Garzik <jgarzik@pobox.com>
* tulip.h, tulip_core.c: If HAS_PCI_MWI is set for a
given chip, adjust the csr0 values not according to
@@ -264,7 +264,7 @@
alignment and system cache size. Currently MWI bit is set
only if the MWI bit is present in the PCI command register.
-2001-05-11 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-11 Jeff Garzik <jgarzik@pobox.com>
* media.c (tulip_select_media):
For media types 1 and 3, only use the provided eeprom
@@ -274,7 +274,7 @@
ensures that the csr6 value is written if an update
is needed.
-2001-05-10 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-10 Jeff Garzik <jgarzik@pobox.com>
Merge PNIC-II-specific stuff from Becker's tulip.c:
@@ -284,13 +284,13 @@
* tulip_core.c (tulip_tx_timeout): Add specific
debugging for PNIC2.
-2001-05-10 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-10 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (tulip_init_one): Print out
tulip%d instead of PCI device number, for
consistency.
-2001-05-10 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-10 Jeff Garzik <jgarzik@pobox.com>
* Merge changes from Becker's tulip.c:
Fix bugs in ioctl.
@@ -299,7 +299,7 @@
Set CSR14 autonegotiation bit for media types 2 and 4,
where the SIA CSR setup values are not provided.
-2001-05-10 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-10 Jeff Garzik <jgarzik@pobox.com>
* media.c (tulip_select_media): Only update MII
advertising value if startup arg < 2.
@@ -313,7 +313,7 @@
value 2 as 'startup' arg to select_media, to avoid updating
MII advertising value.
-2001-05-10 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-10 Jeff Garzik <jgarzik@pobox.com>
* pnic.c (pnic_check_duplex): remove
pnic.c (pnic_lnk_change, pnic_timer): use
@@ -326,13 +326,13 @@
(found by Manfred Spraul)
-2001-05-10 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-10 Jeff Garzik <jgarzik@pobox.com>
* 21142.c, eeprom.c, tulip.h, tulip_core.c:
Remove DPRINTK as another, better method of
debug message printing is available.
-2001-05-09 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-05-09 Jeff Garzik <jgarzik@pobox.com>
* 21142.c (t21142_lnk_change): Pass arg startup==1
to tulip_select_media, in order to force csr13 to be
@@ -344,32 +344,32 @@
* interrupt.c: Better PCI bus error reporting.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: Now that dev->name is only available late
in the probe, insert a hack to replace a not-evaluated
"eth%d" string with an evaluated "tulip%d" string.
Also, remove obvious comment and an indentation cleanup.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: If we are a module, always print out the
version string. If we are built into the kernel, only print
the version string if at least one tulip is detected.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
Merged from Becker's tulip.c 0.92t:
* tulip_core.c: Add support for Conexant LANfinity.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: Only suspend/resume if the interface
is up and running. Use alloc_etherdev and pci_request_regions.
Spelling fix.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: Remove code that existed when one or more of
the following defines existed. These defines were never used
@@ -382,7 +382,7 @@
* media.c: Add barrier() to mdio_read/write's PNIC status check
loops.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
Merged from Becker's tulip.c 0.92t:
@@ -399,20 +399,20 @@
they are in mdio_read/write now. Use mask to limit
phy number in tulip_init_one's MII scan.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
Merged from Becker's tulip.c 0.92t:
* 21142.c, tulip_core.c: PNIC2 MAC address and NWay fixes.
* tulip.h: Add FullDuplex constant, used in above change.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
* timer.c: Do not call netif_carrier_{on,off}, it is not used in
the main tree. Leave code in, disabled, as markers for future
carrier notification.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
Merged from Becker's tulip.c 0.92t, except for the tulip.h
whitespace cleanup:
@@ -431,14 +431,14 @@
Prefer COMET_MAC_ADDR flag test to chip_id test in set_rx_mode.
Store built mc_filter for later use in intr handler by Comets.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: Use tp->cur_tx when building the
setup frame, instead of assuming that the setup
frame is always built in slot zero. This case is
hit during PM resume.
-2001-04-03 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-04-03 Jeff Garzik <jgarzik@pobox.com>
* *.c: Update file headers (copyright, urls, etc.)
* Makefile: re-order to that chip-specific modules on own line
@@ -446,7 +446,7 @@
* tulip_core.c: merge medianame[] update from tulip.c.
Additional arch-specific rx_copybreak, csr0 values. (various)
-2001-02-20 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-02-20 Jeff Garzik <jgarzik@pobox.com>
* media.c (tulip_select_media): No need to initialize
new_csr6, all cases initialize it properly.
@@ -465,7 +465,7 @@
interrupt handler, as PNIC doesn't support a h/w timer.
* tulip_core.c (tulip_tbl[]): Modify default csr6
-2001-02-11 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-02-11 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (tulip_init_one): Call pci_enable_device
to ensure wakeup/resource assignment before checking those
@@ -474,30 +474,30 @@
(tulip_suspend, tulip_resume, tulip_remove_one): Call
pci_power_on/off (commented out for now).
-2001-02-10 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-02-10 Jeff Garzik <jgarzik@pobox.com>
* tulip.h: Add CFDD_xxx bits for Tulip power management
* tulip_core.c (tulip_set_power_state): New function,
manipulating Tulip chip power state where supported.
(tulip_up, tulip_down, tulip_init_one): Use it.
-2001-02-10 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-02-10 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (tulip_tx_timeout): Call netif_wake_queue
to ensure the next Tx is always sent to us.
-2001-01-27 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-01-27 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (tulip_remove_one): Fix mem leak by freeing
tp->media_tbl. Add check for !dev, reformat code appropriately.
-2001-01-27 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-01-27 Jeff Garzik <jgarzik@pobox.com>
* tulip_tbl[]: Comment all entries to make order and chip_id
relationship more clear.
* tulip_pci_tbl[]: Add new Accton PCI id (COMET chipset).
-2001-01-16 Jeff Garzik <jgarzik@mandrakesoft.com>
+2001-01-16 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: static vars no longer explicitly
initialized to zero.
@@ -532,7 +532,7 @@
medianame[] and block_name[] arrays to avoid oops due
to bad values returned from hardware.
-2000-11-02 Jeff Garzik <jgarzik@mandrakesoft.com>
+2000-11-02 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c (set_rx_mode): This is synchronized via
dev->xmit_lock, so only the queueing of the setup frame needs to
@@ -547,13 +547,13 @@
* tulip_core.c (tulip_init_ring, tulip_start_xmit, set_rx_mode):
Likewise.
-2000-10-18 Jeff Garzik <jgarzik@mandrakesoft.com>
+2000-10-18 Jeff Garzik <jgarzik@pobox.com>
* tulip_core.c: (tulip_init_one) Print out ethernet interface
on error. Print out a message when pci_enable_device fails.
Handle DMA alloc failure.
-2000-10-18 Jeff Garzik <jgarzik@mandrakesoft.com>
+2000-10-18 Jeff Garzik <jgarzik@pobox.com>
* Makefile: New file.
* tulip_core.c (tulip_init_one): Correct error messages
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)