patch-2.4.21 linux-2.4.21/drivers/ide/cy82c693.c
Next file: linux-2.4.21/drivers/ide/dtc2278.c
Previous file: linux-2.4.21/drivers/ide/cs5530.c
Back to the patch index
Back to the overall index
- Lines: 450
- Date:
1969-12-31 16:00:00.000000000 -0800
- Orig file:
linux-2.4.20/drivers/ide/cy82c693.c
- Orig date:
2001-05-19 17:43:06.000000000 -0700
diff -urN linux-2.4.20/drivers/ide/cy82c693.c linux-2.4.21/drivers/ide/cy82c693.c
@@ -1,449 +0,0 @@
-/*
- * linux/drivers/ide/cy82c693.c Version 0.34 Dec. 13, 1999
- *
- * Copyright (C) 1998-2000 Andreas S. Krebs (akrebs@altavista.net), Maintainer
- * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>, Integrater
- *
- * CYPRESS CY82C693 chipset IDE controller
- *
- * The CY82C693 chipset is used on Digital's PC-Alpha 164SX boards.
- * Writting the driver was quite simple, since most of the job is
- * done by the generic pci-ide support.
- * The hard part was finding the CY82C693's datasheet on Cypress's
- * web page :-(. But Altavista solved this problem :-).
- *
- *
- * Notes:
- * - I recently got a 16.8G IBM DTTA, so I was able to test it with
- * a large and fast disk - the results look great, so I'd say the
- * driver is working fine :-)
- * hdparm -t reports 8.17 MB/sec at about 6% CPU usage for the DTTA
- * - this is my first linux driver, so there's probably a lot of room
- * for optimizations and bug fixing, so feel free to do it.
- * - use idebus=xx parameter to set PCI bus speed - needed to calc
- * timings for PIO modes (default will be 40)
- * - if using PIO mode it's a good idea to set the PIO mode and
- * 32-bit I/O support (if possible), e.g. hdparm -p2 -c1 /dev/hda
- * - I had some problems with my IBM DHEA with PIO modes < 2
- * (lost interrupts) ?????
- * - first tests with DMA look okay, they seem to work, but there is a
- * problem with sound - the BusMaster IDE TimeOut should fixed this
- *
- *
- * History:
- * AMH@1999-08-24: v0.34 init_cy82c693_chip moved to pci_init_cy82c693
- * ASK@1999-01-23: v0.33 made a few minor code clean ups
- * removed DMA clock speed setting by default
- * added boot message
- * ASK@1998-11-01: v0.32 added support to set BusMaster IDE TimeOut
- * added support to set DMA Controller Clock Speed
- * ASK@1998-10-31: v0.31 fixed problem with setting to high DMA modes on some drive
- * ASK@1998-10-29: v0.3 added support to set DMA modes
- * ASK@1998-10-28: v0.2 added support to set PIO modes
- * ASK@1998-10-27: v0.1 first version - chipset detection
- *
- */
-
-#include <linux/config.h>
-#include <linux/types.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-#include "ide_modes.h"
-
-/* the current version */
-#define CY82_VERSION "CY82C693U driver v0.34 99-13-12 Andreas S. Krebs (akrebs@altavista.net)"
-
-/*
- * The following are used to debug the driver.
- */
-#define CY82C693_DEBUG_LOGS 0
-#define CY82C693_DEBUG_INFO 0
-
-/* define CY82C693_SETDMA_CLOCK to set DMA Controller Clock Speed to ATCLK */
-#undef CY82C693_SETDMA_CLOCK
-
-/*
- * note: the value for busmaster timeout is tricky and i got it by trial and error !
- * using a to low value will cause DMA timeouts and drop IDE performance
- * using a to high value will cause audio playback to scatter
- * if you know a better value or how to calc it, please let me know
- */
-#define BUSMASTER_TIMEOUT 0x50 /* twice the value written in cy82c693ub datasheet */
-/*
- * the value above was tested on my machine and it seems to work okay
- */
-
-/* here are the offset definitions for the registers */
-#define CY82_IDE_CMDREG 0x04
-#define CY82_IDE_ADDRSETUP 0x48
-#define CY82_IDE_MASTER_IOR 0x4C
-#define CY82_IDE_MASTER_IOW 0x4D
-#define CY82_IDE_SLAVE_IOR 0x4E
-#define CY82_IDE_SLAVE_IOW 0x4F
-#define CY82_IDE_MASTER_8BIT 0x50
-#define CY82_IDE_SLAVE_8BIT 0x51
-
-#define CY82_INDEX_PORT 0x22
-#define CY82_DATA_PORT 0x23
-
-#define CY82_INDEX_CTRLREG1 0x01
-#define CY82_INDEX_CHANNEL0 0x30
-#define CY82_INDEX_CHANNEL1 0x31
-#define CY82_INDEX_TIMEOUT 0x32
-
-/* the max PIO mode - from datasheet */
-#define CY82C693_MAX_PIO 4
-
-/* the min and max PCI bus speed in MHz - from datasheet */
-#define CY82C963_MIN_BUS_SPEED 25
-#define CY82C963_MAX_BUS_SPEED 33
-
-/* the struct for the PIO mode timings */
-typedef struct pio_clocks_s {
- byte address_time; /* Address setup (clocks) */
- byte time_16r; /* clocks for 16bit IOR (0xF0=Active/data, 0x0F=Recovery) */
- byte time_16w; /* clocks for 16bit IOW (0xF0=Active/data, 0x0F=Recovery) */
- byte time_8; /* clocks for 8bit (0xF0=Active/data, 0x0F=Recovery) */
-} pio_clocks_t;
-
-/*
- * calc clocks using bus_speed
- * returns (rounded up) time in bus clocks for time in ns
- */
-static int calc_clk (int time, int bus_speed)
-{
- int clocks;
-
- clocks = (time*bus_speed+999)/1000 -1;
-
- if (clocks < 0)
- clocks = 0;
-
- if (clocks > 0x0F)
- clocks = 0x0F;
-
- return clocks;
-}
-
-/*
- * compute the values for the clock registers for PIO
- * mode and pci_clk [MHz] speed
- *
- * NOTE: for mode 0,1 and 2 drives 8-bit IDE command control registers are used
- * for mode 3 and 4 drives 8 and 16-bit timings are the same
- *
- */
-static void compute_clocks (byte pio, pio_clocks_t *p_pclk)
-{
- int clk1, clk2;
- int bus_speed = system_bus_clock(); /* get speed of PCI bus */
-
- /* we don't check against CY82C693's min and max speed,
- * so you can play with the idebus=xx parameter
- */
-
- if (pio > CY82C693_MAX_PIO)
- pio = CY82C693_MAX_PIO;
-
- /* let's calc the address setup time clocks */
- p_pclk->address_time = (byte)calc_clk(ide_pio_timings[pio].setup_time, bus_speed);
-
- /* let's calc the active and recovery time clocks */
- clk1 = calc_clk(ide_pio_timings[pio].active_time, bus_speed);
-
- /* calc recovery timing */
- clk2 = ide_pio_timings[pio].cycle_time -
- ide_pio_timings[pio].active_time -
- ide_pio_timings[pio].setup_time;
-
- clk2 = calc_clk(clk2, bus_speed);
-
- clk1 = (clk1<<4)|clk2; /* combine active and recovery clocks */
-
- /* note: we use the same values for 16bit IOR and IOW
- * those are all the same, since I don't have other
- * timings than those from ide_modes.h
- */
-
- p_pclk->time_16r = (byte)clk1;
- p_pclk->time_16w = (byte)clk1;
-
- /* what are good values for 8bit ?? */
- p_pclk->time_8 = (byte)clk1;
-}
-
-#ifdef CONFIG_BLK_DEV_IDEDMA
-/*
- * set DMA mode a specific channel for CY82C693
- */
-static void cy82c693_dma_enable (ide_drive_t *drive, int mode, int single)
-{
- byte index;
- byte data;
-
- if (mode>2) /* make sure we set a valid mode */
- mode = 2;
-
- if (mode > drive->id->tDMA) /* to be absolutly sure we have a valid mode */
- mode = drive->id->tDMA;
-
- index = (HWIF(drive)->channel==0) ? CY82_INDEX_CHANNEL0 : CY82_INDEX_CHANNEL1;
-
-#if CY82C693_DEBUG_LOGS
- /* for debug let's show the previous values */
-
- OUT_BYTE(index, CY82_INDEX_PORT);
- data = IN_BYTE(CY82_DATA_PORT);
-
- printk (KERN_INFO "%s (ch=%d, dev=%d): DMA mode is %d (single=%d)\n", drive->name, HWIF(drive)->channel, drive->select.b.unit, (data&0x3), ((data>>2)&1));
-#endif /* CY82C693_DEBUG_LOGS */
-
- data = (byte)mode|(byte)(single<<2);
-
- OUT_BYTE(index, CY82_INDEX_PORT);
- OUT_BYTE(data, CY82_DATA_PORT);
-
-#if CY82C693_DEBUG_INFO
- printk (KERN_INFO "%s (ch=%d, dev=%d): set DMA mode to %d (single=%d)\n", drive->name, HWIF(drive)->channel, drive->select.b.unit, mode, single);
-#endif /* CY82C693_DEBUG_INFO */
-
- /*
- * note: below we set the value for Bus Master IDE TimeOut Register
- * I'm not absolutly sure what this does, but it solved my problem
- * with IDE DMA and sound, so I now can play sound and work with
- * my IDE driver at the same time :-)
- *
- * If you know the correct (best) value for this register please
- * let me know - ASK
- */
-
- data = BUSMASTER_TIMEOUT;
- OUT_BYTE(CY82_INDEX_TIMEOUT, CY82_INDEX_PORT);
- OUT_BYTE(data, CY82_DATA_PORT);
-
-#if CY82C693_DEBUG_INFO
- printk (KERN_INFO "%s: Set IDE Bus Master TimeOut Register to 0x%X\n", drive->name, data);
-#endif /* CY82C693_DEBUG_INFO */
-}
-
-/*
- * used to set DMA mode for CY82C693 (single and multi modes)
- */
-static int cy82c693_dmaproc(ide_dma_action_t func, ide_drive_t *drive)
-{
- /*
- * if the function is dma on, set dma mode for drive everything
- * else is done by the defaul func
- */
- if (func == ide_dma_on) {
- struct hd_driveid *id = drive->id;
-
-#if CY82C693_DEBUG_INFO
- printk (KERN_INFO "dma_on: %s\n", drive->name);
-#endif /* CY82C693_DEBUG_INFO */
-
- if (id != NULL) {
- /* Enable DMA on any drive that has DMA (multi or single) enabled */
- if (id->field_valid & 2) { /* regular DMA */
- int mmode, smode;
-
- mmode = id->dma_mword & (id->dma_mword >> 8);
- smode = id->dma_1word & (id->dma_1word >> 8);
-
- if (mmode != 0)
- cy82c693_dma_enable(drive, (mmode >> 1), 0); /* enable multi */
- else if (smode != 0)
- cy82c693_dma_enable(drive, (smode >> 1), 1); /* enable single */
- }
- }
- }
- return ide_dmaproc(func, drive);
-}
-#endif /* CONFIG_BLK_DEV_IDEDMA */
-
-/*
- * tune ide drive - set PIO mode
- */
-static void cy82c693_tune_drive (ide_drive_t *drive, byte pio)
-{
- ide_hwif_t *hwif = HWIF(drive);
- struct pci_dev *dev = hwif->pci_dev;
- pio_clocks_t pclk;
- unsigned int addrCtrl;
-
- /* select primary or secondary channel */
- if (hwif->index > 0) { /* drive is on the secondary channel */
- dev = pci_find_slot(dev->bus->number, dev->devfn+1);
- if (!dev) {
- printk(KERN_ERR "%s: tune_drive: Cannot find secondary interface!\n", drive->name);
- return;
- }
- }
-
-#if CY82C693_DEBUG_LOGS
- /* for debug let's show the register values */
-
- if (drive->select.b.unit == 0) {
- /*
- * get master drive registers
- * address setup control register
- * is 32 bit !!!
- */
- pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
- addrCtrl &= 0x0F;
-
- /* now let's get the remaining registers */
- pci_read_config_byte(dev, CY82_IDE_MASTER_IOR, &pclk.time_16r);
- pci_read_config_byte(dev, CY82_IDE_MASTER_IOW, &pclk.time_16w);
- pci_read_config_byte(dev, CY82_IDE_MASTER_8BIT, &pclk.time_8);
- } else {
- /*
- * set slave drive registers
- * address setup control register
- * is 32 bit !!!
- */
- pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
-
- addrCtrl &= 0xF0;
- addrCtrl >>= 4;
-
- /* now let's get the remaining registers */
- pci_read_config_byte(dev, CY82_IDE_SLAVE_IOR, &pclk.time_16r);
- pci_read_config_byte(dev, CY82_IDE_SLAVE_IOW, &pclk.time_16w);
- pci_read_config_byte(dev, CY82_IDE_SLAVE_8BIT, &pclk.time_8);
- }
-
- printk (KERN_INFO "%s (ch=%d, dev=%d): PIO timing is (addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n", drive->name, hwif->channel, drive->select.b.unit, addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
-#endif /* CY82C693_DEBUG_LOGS */
-
- /* first let's calc the pio modes */
- pio = ide_get_best_pio_mode(drive, pio, CY82C693_MAX_PIO, NULL);
-
-#if CY82C693_DEBUG_INFO
- printk (KERN_INFO "%s: Selected PIO mode %d\n", drive->name, pio);
-#endif /* CY82C693_DEBUG_INFO */
-
- compute_clocks(pio, &pclk); /* let's calc the values for this PIO mode */
-
- /* now let's write the clocks registers */
- if (drive->select.b.unit == 0) {
- /*
- * set master drive
- * address setup control register
- * is 32 bit !!!
- */
- pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
-
- addrCtrl &= (~0xF);
- addrCtrl |= (unsigned int)pclk.address_time;
- pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);
-
- /* now let's set the remaining registers */
- pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r);
- pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w);
- pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8);
-
- addrCtrl &= 0xF;
- } else {
- /*
- * set slave drive
- * address setup control register
- * is 32 bit !!!
- */
- pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl);
-
- addrCtrl &= (~0xF0);
- addrCtrl |= ((unsigned int)pclk.address_time<<4);
- pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl);
-
- /* now let's set the remaining registers */
- pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r);
- pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w);
- pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8);
-
- addrCtrl >>= 4;
- addrCtrl &= 0xF;
- }
-
-#if CY82C693_DEBUG_INFO
- printk (KERN_INFO "%s (ch=%d, dev=%d): set PIO timing to (addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n", drive->name, hwif->channel, drive->select.b.unit, addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8);
-#endif /* CY82C693_DEBUG_INFO */
-}
-
-/*
- * this function is called during init and is used to setup the cy82c693 chip
- */
-/*
- * FIXME! "pci_init_cy82c693" really should replace
- * the "init_cy82c693_chip", it is the correct location to tinker/setup
- * the device prior to INIT.
- */
-
-unsigned int __init pci_init_cy82c693(struct pci_dev *dev, const char *name)
-{
-#ifdef CY82C693_SETDMA_CLOCK
- byte data;
-#endif /* CY82C693_SETDMA_CLOCK */
-
- /* write info about this verion of the driver */
- printk (KERN_INFO CY82_VERSION "\n");
-
-#ifdef CY82C693_SETDMA_CLOCK
- /* okay let's set the DMA clock speed */
-
- OUT_BYTE(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT);
- data = IN_BYTE(CY82_DATA_PORT);
-
-#if CY82C693_DEBUG_INFO
- printk (KERN_INFO "%s: Peripheral Configuration Register: 0x%X\n", name, data);
-#endif /* CY82C693_DEBUG_INFO */
-
- /*
- * for some reason sometimes the DMA controller
- * speed is set to ATCLK/2 ???? - we fix this here
- *
- * note: i don't know what causes this strange behaviour,
- * but even changing the dma speed doesn't solve it :-(
- * the ide performance is still only half the normal speed
- *
- * if anybody knows what goes wrong with my machine, please
- * let me know - ASK
- */
-
- data |= 0x03;
-
- OUT_BYTE(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT);
- OUT_BYTE(data, CY82_DATA_PORT);
-
-#if CY82C693_DEBUG_INFO
- printk (KERN_INFO "%s: New Peripheral Configuration Register: 0x%X\n", name, data);
-#endif /* CY82C693_DEBUG_INFO */
-
-#endif /* CY82C693_SETDMA_CLOCK */
- return 0;
-}
-
-/*
- * the init function - called for each ide channel once
- */
-void __init ide_init_cy82c693(ide_hwif_t *hwif)
-{
- hwif->chipset = ide_cy82c693;
- hwif->tuneproc = &cy82c693_tune_drive;
- hwif->drives[0].autotune = 1;
- hwif->drives[1].autotune = 1;
- hwif->autodma = 0;
-
-#ifdef CONFIG_BLK_DEV_IDEDMA
- if (hwif->dma_base) {
- hwif->dmaproc = &cy82c693_dmaproc;
- if (!noautodma)
- hwif->autodma = 1;
- }
-#endif /* CONFIG_BLK_DEV_IDEDMA */
-}
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)