patch-2.4.19 linux-2.4.19/drivers/video/virgefb.h

Next file: linux-2.4.19/drivers/zorro/zorro.ids
Previous file: linux-2.4.19/drivers/video/virgefb.c
Back to the patch index
Back to the overall index

diff -urN linux-2.4.18/drivers/video/virgefb.h linux-2.4.19/drivers/video/virgefb.h
@@ -0,0 +1,288 @@
+/*
+ * linux/drivers/video/virgefb.h -- CyberVision64 definitions for the
+ *                                  text console driver.
+ *
+ *   Copyright (c) 1998 Alan Bair
+ *
+ * This file is based on the initial port to Linux of grf_cvreg.h:
+ *
+ *   Copyright (c) 1997 Antonio Santos
+ *
+ * The original work is from the NetBSD CyberVision 64 framebuffer driver 
+ * and support files (grf_cv.c, grf_cvreg.h, ite_cv.c):
+ * Permission to use the source of this driver was obtained from the
+ * author Michael Teske by Alan Bair.
+ *
+ *   Copyright (c) 1995 Michael Teske
+ *
+ * History:
+ *
+ *
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file COPYING in the main directory of this archive
+ * for more details.
+ */
+
+/* Enhanced register mapping (MMIO mode) */
+
+#define S3_CRTC_ADR    0x03d4
+#define S3_CRTC_DATA   0x03d5
+
+#define S3_REG_LOCK2	0x39
+#define S3_HGC_MODE	0x45
+
+#define S3_HWGC_ORGX_H	0x46
+#define S3_HWGC_ORGX_L	0x47
+#define S3_HWGC_ORGY_H	0x48
+#define S3_HWGC_ORGY_L	0x49
+#define S3_HWGC_DX	0x4e
+#define S3_HWGC_DY	0x4f
+
+#define S3_LAW_CTL	0x58
+
+/**************************************************/
+
+/*
+ * Defines for the used register addresses (mw)
+ *
+ * NOTE: There are some registers that have different addresses when
+ *       in mono or color mode. We only support color mode, and thus
+ *       some addresses won't work in mono-mode!
+ *
+ * General and VGA-registers taken from retina driver. Fixed a few
+ * bugs in it. (SR and GR read address is Port + 1, NOT Port)
+ *
+ */
+
+/* General Registers: */
+#define GREG_MISC_OUTPUT_R	0x03CC
+#define GREG_MISC_OUTPUT_W	0x03C2	
+#define GREG_FEATURE_CONTROL_R	0x03CA 
+#define GREG_FEATURE_CONTROL_W	0x03DA
+#define GREG_INPUT_STATUS0_R	0x03C2
+#define GREG_INPUT_STATUS1_R	0x03DA
+
+/* Setup Registers: */
+#define SREG_VIDEO_SUBS_ENABLE	0x03C3	/* virge */
+
+/* Attribute Controller: */
+#define ACT_ADDRESS		0x03C0
+#define ACT_ADDRESS_R		0x03C1
+#define ACT_ADDRESS_W		0x03C0
+#define ACT_ADDRESS_RESET	0x03DA
+#define ACT_ID_PALETTE0		0x00
+#define ACT_ID_PALETTE1		0x01
+#define ACT_ID_PALETTE2		0x02
+#define ACT_ID_PALETTE3		0x03
+#define ACT_ID_PALETTE4		0x04
+#define ACT_ID_PALETTE5		0x05
+#define ACT_ID_PALETTE6		0x06
+#define ACT_ID_PALETTE7		0x07
+#define ACT_ID_PALETTE8		0x08
+#define ACT_ID_PALETTE9		0x09
+#define ACT_ID_PALETTE10	0x0A
+#define ACT_ID_PALETTE11	0x0B
+#define ACT_ID_PALETTE12	0x0C
+#define ACT_ID_PALETTE13	0x0D
+#define ACT_ID_PALETTE14	0x0E
+#define ACT_ID_PALETTE15	0x0F
+#define ACT_ID_ATTR_MODE_CNTL	0x10
+#define ACT_ID_OVERSCAN_COLOR	0x11
+#define ACT_ID_COLOR_PLANE_ENA	0x12
+#define ACT_ID_HOR_PEL_PANNING	0x13
+#define ACT_ID_COLOR_SELECT	0x14    /* virge PX_PADD  pixel padding register */
+
+/* Graphics Controller: */
+#define GCT_ADDRESS		0x03CE
+#define GCT_ADDRESS_R		0x03CF
+#define GCT_ADDRESS_W		0x03CF
+#define GCT_ID_SET_RESET	0x00
+#define GCT_ID_ENABLE_SET_RESET	0x01
+#define GCT_ID_COLOR_COMPARE	0x02
+#define GCT_ID_DATA_ROTATE	0x03
+#define GCT_ID_READ_MAP_SELECT	0x04
+#define GCT_ID_GRAPHICS_MODE	0x05
+#define GCT_ID_MISC		0x06
+#define GCT_ID_COLOR_XCARE	0x07
+#define GCT_ID_BITMASK		0x08
+
+/* Sequencer: */
+#define SEQ_ADDRESS		0x03C4
+#define SEQ_ADDRESS_R		0x03C5
+#define SEQ_ADDRESS_W		0x03C5
+#define SEQ_ID_RESET		0x00
+#define SEQ_ID_CLOCKING_MODE	0x01
+#define SEQ_ID_MAP_MASK		0x02
+#define SEQ_ID_CHAR_MAP_SELECT	0x03
+#define SEQ_ID_MEMORY_MODE	0x04
+#define SEQ_ID_UNKNOWN1		0x05
+#define SEQ_ID_UNKNOWN2		0x06
+#define SEQ_ID_UNKNOWN3		0x07
+/* S3 extensions */
+#define SEQ_ID_UNLOCK_EXT	0x08
+#define SEQ_ID_EXT_SEQ_REG9	0x09	/* b7 = 1 extended reg access by MMIO only */
+#define SEQ_ID_BUS_REQ_CNTL	0x0A
+#define SEQ_ID_EXT_MISC_SEQ	0x0B
+#define SEQ_ID_UNKNOWN4		0x0C
+#define SEQ_ID_EXT_SEQ		0x0D
+#define SEQ_ID_UNKNOWN5		0x0E
+#define SEQ_ID_UNKNOWN6		0x0F
+#define SEQ_ID_MCLK_LO		0x10
+#define SEQ_ID_MCLK_HI		0x11
+#define SEQ_ID_DCLK_LO		0x12
+#define SEQ_ID_DCLK_HI		0x13
+#define SEQ_ID_CLKSYN_CNTL_1	0x14
+#define SEQ_ID_CLKSYN_CNTL_2	0x15
+#define SEQ_ID_CLKSYN_TEST_HI	0x16	/* reserved for S3 testing of the */
+#define SEQ_ID_CLKSYN_TEST_LO	0x17	/* internal clock synthesizer   */
+#define SEQ_ID_RAMDAC_CNTL	0x18
+#define SEQ_ID_MORE_MAGIC	0x1A
+#define SEQ_ID_SIGNAL_SELECT	0x1C	/* new for virge */
+
+/* CRT Controller: */
+#define CRT_ADDRESS		0x03D4
+#define CRT_ADDRESS_R		0x03D5
+#define CRT_ADDRESS_W		0x03D5
+#define CRT_ID_HOR_TOTAL	0x00
+#define CRT_ID_HOR_DISP_ENA_END	0x01
+#define CRT_ID_START_HOR_BLANK	0x02
+#define CRT_ID_END_HOR_BLANK	0x03
+#define CRT_ID_START_HOR_RETR	0x04
+#define CRT_ID_END_HOR_RETR	0x05
+#define CRT_ID_VER_TOTAL	0x06
+#define CRT_ID_OVERFLOW		0x07
+#define CRT_ID_PRESET_ROW_SCAN	0x08
+#define CRT_ID_MAX_SCAN_LINE	0x09
+#define CRT_ID_CURSOR_START	0x0A
+#define CRT_ID_CURSOR_END	0x0B
+#define CRT_ID_START_ADDR_HIGH	0x0C
+#define CRT_ID_START_ADDR_LOW	0x0D
+#define CRT_ID_CURSOR_LOC_HIGH	0x0E
+#define CRT_ID_CURSOR_LOC_LOW	0x0F
+#define CRT_ID_START_VER_RETR	0x10
+#define CRT_ID_END_VER_RETR	0x11
+#define CRT_ID_VER_DISP_ENA_END	0x12
+#define CRT_ID_SCREEN_OFFSET	0x13
+#define CRT_ID_UNDERLINE_LOC	0x14
+#define CRT_ID_START_VER_BLANK	0x15
+#define CRT_ID_END_VER_BLANK	0x16
+#define CRT_ID_MODE_CONTROL	0x17
+#define CRT_ID_LINE_COMPARE	0x18
+#define CRT_ID_GD_LATCH_RBACK	0x22
+#define CRT_ID_ACT_TOGGLE_RBACK	0x24
+#define CRT_ID_ACT_INDEX_RBACK	0x26
+/* S3 extensions: S3 VGA Registers */
+#define CRT_ID_DEVICE_HIGH	0x2D
+#define CRT_ID_DEVICE_LOW	0x2E
+#define CRT_ID_REVISION 	0x2F
+#define CRT_ID_CHIP_ID_REV	0x30
+#define CRT_ID_MEMORY_CONF	0x31
+#define CRT_ID_BACKWAD_COMP_1	0x32
+#define CRT_ID_BACKWAD_COMP_2	0x33
+#define CRT_ID_BACKWAD_COMP_3	0x34
+#define CRT_ID_REGISTER_LOCK	0x35
+#define CRT_ID_CONFIG_1 	0x36
+#define CRT_ID_CONFIG_2 	0x37
+#define CRT_ID_REGISTER_LOCK_1	0x38
+#define CRT_ID_REGISTER_LOCK_2	0x39
+#define CRT_ID_MISC_1		0x3A
+#define CRT_ID_DISPLAY_FIFO	0x3B
+#define CRT_ID_LACE_RETR_START	0x3C
+/* S3 extensions: System Control Registers  */
+#define CRT_ID_SYSTEM_CONFIG	0x40
+#define CRT_ID_BIOS_FLAG	0x41
+#define CRT_ID_LACE_CONTROL	0x42
+#define CRT_ID_EXT_MODE 	0x43
+#define CRT_ID_HWGC_MODE	0x45	/* HWGC = Hardware Graphics Cursor */
+#define CRT_ID_HWGC_ORIGIN_X_HI	0x46
+#define CRT_ID_HWGC_ORIGIN_X_LO	0x47
+#define CRT_ID_HWGC_ORIGIN_Y_HI	0x48
+#define CRT_ID_HWGC_ORIGIN_Y_LO	0x49
+#define CRT_ID_HWGC_FG_STACK	0x4A
+#define CRT_ID_HWGC_BG_STACK	0x4B
+#define CRT_ID_HWGC_START_AD_HI	0x4C
+#define CRT_ID_HWGC_START_AD_LO	0x4D
+#define CRT_ID_HWGC_DSTART_X	0x4E
+#define CRT_ID_HWGC_DSTART_Y	0x4F
+/* S3 extensions: System Extension Registers  */
+#define CRT_ID_EXT_SYS_CNTL_1	0x50	/* NOT a virge register */
+#define CRT_ID_EXT_SYS_CNTL_2	0x51
+#define CRT_ID_EXT_BIOS_FLAG_1	0x52
+#define CRT_ID_EXT_MEM_CNTL_1	0x53
+#define CRT_ID_EXT_MEM_CNTL_2	0x54
+#define CRT_ID_EXT_DAC_CNTL	0x55
+#define CRT_ID_EX_SYNC_1	0x56
+#define CRT_ID_EX_SYNC_2	0x57
+#define CRT_ID_LAW_CNTL		0x58	/* LAW = Linear Address Window */
+#define CRT_ID_LAW_POS_HI	0x59
+#define CRT_ID_LAW_POS_LO	0x5A
+#define CRT_ID_GOUT_PORT	0x5C
+#define CRT_ID_EXT_HOR_OVF	0x5D
+#define CRT_ID_EXT_VER_OVF	0x5E
+#define CRT_ID_EXT_MEM_CNTL_3	0x60	/* NOT a virge register */
+#define CRT_ID_EXT_MEM_CNTL_4	0x61
+#define CRT_ID_EX_SYNC_3	0x63	/* NOT a virge register */
+#define CRT_ID_EXT_MISC_CNTL	0x65
+#define CRT_ID_EXT_MISC_CNTL_1	0x66
+#define CRT_ID_EXT_MISC_CNTL_2	0x67
+#define CRT_ID_CONFIG_3 	0x68
+#define CRT_ID_EXT_SYS_CNTL_3	0x69
+#define CRT_ID_EXT_SYS_CNTL_4	0x6A
+#define CRT_ID_EXT_BIOS_FLAG_3	0x6B
+#define CRT_ID_EXT_BIOS_FLAG_4	0x6C
+/* S3 virge extensions: more System Extension Registers  */
+#define CRT_ID_EXT_BIOS_FLAG_5	0x6D
+#define CRT_ID_EXT_DAC_TEST	0x6E
+#define CRT_ID_CONFIG_4 	0x6F
+
+/* Video DAC */
+#define VDAC_ADDRESS		0x03c8
+#define VDAC_ADDRESS_W		0x03c8
+#define VDAC_ADDRESS_R		0x03c7
+#define VDAC_STATE		0x03c7
+#define VDAC_DATA		0x03c9
+#define VDAC_MASK		0x03c6
+
+/* Miscellaneous Registers */
+#define MR_SUBSYSTEM_STATUS_R		0x8504	/* new for virge */
+#define MR_SUBSYSTEM_CNTL_W		0x8504	/* new for virge */
+#define MR_ADVANCED_FUNCTION_CONTROL	0x850C	/* new for virge */
+
+/* Blitter  */
+#define BLT_COMMAND_SET		0xA500
+#define BLT_SIZE_X_Y		0xA504
+#define BLT_SRC_X_Y		0xA508
+#define BLT_DEST_X_Y		0xA50C
+
+#define BLT_SRC_BASE		0xa4d4
+#define BLT_DEST_BASE		0xa4d8
+#define BLT_CLIP_LEFT_RIGHT	0xa4dc
+#define BLT_CLIP_TOP_BOTTOM	0xa4e0
+#define BLT_SRC_DEST_STRIDE	0xa4e4
+#define BLT_MONO_PATTERN_0	0xa4e8
+#define BLT_MONO_PATTERN_1	0xa4ec
+#define BLT_PATTERN_COLOR	0xa4f4
+
+#define L2D_COMMAND_SET		0xA900
+#define L2D_CLIP_LEFT_RIGHT	0xA8DC
+#define L2D_CLIP_TOP_BOTTOM	0xA8E0
+
+#define P2D_COMMAND_SET		0xAD00
+#define P2D_CLIP_LEFT_RIGHT	0xACDC
+#define P2D_CLIP_TOP_BOTTOM	0xACE0
+
+#define CMD_NOP		(0xf << 27)	/* %1111 << 27, was 0x07 */ 
+#define S3V_BITBLT	(0x0 << 27)
+#define S3V_RECTFILL	(0x2 << 27)
+#define S3V_AUTOEXE	0x01
+#define S3V_HWCLIP	0x02
+#define S3V_DRAW	0x20
+#define S3V_DST_8BPP	0x00
+#define S3V_DST_16BPP	0x04
+#define S3V_DST_24BPP	0x08
+#define S3V_MONO_PAT	0x100
+
+#define S3V_BLT_COPY	(0xcc<<17)
+#define S3V_BLT_CLEAR	(0x00<<17)
+#define S3V_BLT_SET	(0xff<<17)

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)