patch-2.4.19 linux-2.4.19/arch/mips/au1000/common/reset.c

• Lines: 76
• Date: Fri Aug 2 17:39:43 2002
• Orig file: linux-2.4.18/arch/mips/au1000/common/reset.c
• Orig date: Sun Sep 9 10:43:01 2001

diff -urN linux-2.4.18/arch/mips/au1000/common/reset.c linux-2.4.19/arch/mips/au1000/common/reset.c
@@ -36,8 +36,56 @@
 #include <asm/reboot.h>
 #include <asm/system.h>
 
+extern int au_sleep(void);
+
 void au1000_restart(char *command)
 {
+	/* Set all integrated peripherals to disabled states */
+	u32 prid = read_32bit_cp0_register(CP0_PRID);
+
+	printk(KERN_NOTICE "\n** Resetting Integrated Peripherals\n");
+	switch (prid & 0xFF000000)
+	{
+	case 0x00000000: /* Au1000 */
+		outl(0x02, 0xb0000010); /* ac97_enable */
+		outl(0x08, 0xb017fffc); /* usbh_enable - early errata */
+		asm("sync");
+		outl(0x00, 0xb017fffc); /* usbh_enable */
+		outl(0x00, 0xb0200058); /* usbd_enable */
+		outl(0x00, 0xb0300040); /* ir_enable */
+		outl(0x00, 0xb0520000); /* macen0 */
+		outl(0x00, 0xb0520004); /* macen1 */
+		outl(0x00, 0xb1000008); /* i2s_enable  */
+		outl(0x00, 0xb1100100); /* uart0_enable */
+		outl(0x00, 0xb1200100); /* uart1_enable */
+		outl(0x00, 0xb1300100); /* uart2_enable */
+		outl(0x00, 0xb1400100); /* uart3_enable */
+		outl(0x02, 0xb1600100); /* ssi0_enable */
+		outl(0x02, 0xb1680100); /* ssi1_enable */
+		outl(0x00, 0xb1900020); /* sys_freqctrl0 */
+		outl(0x00, 0xb1900024); /* sys_freqctrl1 */
+		outl(0x00, 0xb1900028); /* sys_clksrc */
+		outl(0x00, 0xb1900100); /* sys_pininputen */
+		break;
+	case 0x01000000: /* Au1500 */
+		outl(0x02, 0xb0000010); /* ac97_enable */
+		outl(0x08, 0xb017fffc); /* usbh_enable - early errata */
+		asm("sync");
+		outl(0x00, 0xb017fffc); /* usbh_enable */
+		outl(0x00, 0xb0200058); /* usbd_enable */
+		outl(0x00, 0xb1520000); /* macen0 */
+		outl(0x00, 0xb1520004); /* macen1 */
+		outl(0x00, 0xb1100100); /* uart0_enable */
+		outl(0x00, 0xb1400100); /* uart3_enable */
+		outl(0x00, 0xb1900020); /* sys_freqctrl0 */
+		outl(0x00, 0xb1900024); /* sys_freqctrl1 */
+		outl(0x00, 0xb1900028); /* sys_clksrc */
+		outl(0x00, 0xb1900100); /* sys_pininputen */
+
+	default:
+		break;
+	}
+
 	set_cp0_status(ST0_BEV | ST0_ERL);
 	set_cp0_config(CONF_CM_UNCACHED);
 	flush_cache_all();
@@ -48,10 +96,18 @@
 void au1000_halt(void)
 {
 	printk(KERN_NOTICE "\n** You can safely turn off the power\n");
+#ifdef CONFIG_PM
+	au_sleep();
+
+	/* should not get here */
+	printk(KERN_ERR "Unable to put cpu in sleep mode\n");
+	while(1);
+#else
 	while (1)
 		__asm__(".set\tmips3\n\t"
 	                "wait\n\t"
 			".set\tmips0");
+#endif
 }
 
 void au1000_power_off(void)