patch-2.4.11-dontuse linux/include/asm-ppc/commproc.h

Next file: linux/include/asm-ppc/ide.h
Previous file: linux/include/asm-parisc/processor.h
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.4.10/linux/include/asm-ppc/commproc.h linux/include/asm-ppc/commproc.h
@@ -0,0 +1,796 @@
+/*
+ * BK Id: SCCS/s.commproc.h 1.16 09/27/01 12:41:09 trini
+ */
+
+/*
+ * MPC8xx Communication Processor Module.
+ * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
+ *
+ * This file contains structures and information for the communication
+ * processor channels.  Some CPM control and status is available
+ * throught the MPC8xx internal memory map.  See immap.h for details.
+ * This file only contains what I need for the moment, not the total
+ * CPM capabilities.  I (or someone else) will add definitions as they
+ * are needed.  -- Dan
+ *
+ * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
+ * bytes of the DP RAM and relocates the I2C parameter area to the
+ * IDMA1 space.  The remaining DP RAM is available for buffer descriptors
+ * or other use.
+ */
+#ifndef __CPM_8XX__
+#define __CPM_8XX__
+
+#include <linux/config.h>
+#include <asm/8xx_immap.h>
+
+/* CPM Command register.
+*/
+#define CPM_CR_RST	((ushort)0x8000)
+#define CPM_CR_OPCODE	((ushort)0x0f00)
+#define CPM_CR_CHAN	((ushort)0x00f0)
+#define CPM_CR_FLG	((ushort)0x0001)
+
+/* Some commands (there are more...later)
+*/
+#define CPM_CR_INIT_TRX		((ushort)0x0000)
+#define CPM_CR_INIT_RX		((ushort)0x0001)
+#define CPM_CR_INIT_TX		((ushort)0x0002)
+#define CPM_CR_HUNT_MODE	((ushort)0x0003)
+#define CPM_CR_STOP_TX		((ushort)0x0004)
+#define CPM_CR_RESTART_TX	((ushort)0x0006)
+#define CPM_CR_SET_GADDR	((ushort)0x0008)
+
+/* Channel numbers.
+*/
+#define CPM_CR_CH_SCC1	((ushort)0x0000)
+#define CPM_CR_CH_I2C	((ushort)0x0001)	/* I2C and IDMA1 */
+#define CPM_CR_CH_SCC2	((ushort)0x0004)
+#define CPM_CR_CH_SPI	((ushort)0x0005)	/* SPI / IDMA2 / Timers */
+#define CPM_CR_CH_SCC3	((ushort)0x0008)
+#define CPM_CR_CH_SMC1	((ushort)0x0009)	/* SMC1 / DSP1 */
+#define CPM_CR_CH_SCC4	((ushort)0x000c)
+#define CPM_CR_CH_SMC2	((ushort)0x000d)	/* SMC2 / DSP2 */
+
+#define mk_cr_cmd(CH, CMD)	((CMD << 8) | (CH << 4))
+
+/* The dual ported RAM is multi-functional.  Some areas can be (and are
+ * being) used for microcode.  There is an area that can only be used
+ * as data ram for buffer descriptors, which is all we use right now.
+ * Currently the first 512 and last 256 bytes are used for microcode.
+ */
+#define CPM_DATAONLY_BASE	((uint)0x0800)
+#define CPM_DATAONLY_SIZE	((uint)0x0700)
+#define CPM_DP_NOSPACE		((uint)0x7fffffff)
+
+/* Export the base address of the communication processor registers
+ * and dual port ram.
+ */
+extern	cpm8xx_t	*cpmp;		/* Pointer to comm processor */
+uint		m8xx_cpm_dpalloc(uint size);
+uint		m8xx_cpm_hostalloc(uint size);
+void		m8xx_cpm_setbrg(uint brg, uint rate);
+
+/* Buffer descriptors used by many of the CPM protocols.
+*/
+typedef struct cpm_buf_desc {
+	ushort	cbd_sc;		/* Status and Control */
+	ushort	cbd_datlen;	/* Data length in buffer */
+	uint	cbd_bufaddr;	/* Buffer address in host memory */
+} cbd_t;
+
+#define BD_SC_EMPTY	((ushort)0x8000)	/* Receive is empty */
+#define BD_SC_READY	((ushort)0x8000)	/* Transmit is ready */
+#define BD_SC_WRAP	((ushort)0x2000)	/* Last buffer descriptor */
+#define BD_SC_INTRPT	((ushort)0x1000)	/* Interrupt on change */
+#define BD_SC_LAST	((ushort)0x0800)	/* Last buffer in frame */
+#define BD_SC_CM	((ushort)0x0200)	/* Continous mode */
+#define BD_SC_ID	((ushort)0x0100)	/* Rec'd too many idles */
+#define BD_SC_P		((ushort)0x0100)	/* xmt preamble */
+#define BD_SC_BR	((ushort)0x0020)	/* Break received */
+#define BD_SC_FR	((ushort)0x0010)	/* Framing error */
+#define BD_SC_PR	((ushort)0x0008)	/* Parity error */
+#define BD_SC_OV	((ushort)0x0002)	/* Overrun */
+#define BD_SC_CD	((ushort)0x0001)	/* ?? */
+
+/* Parameter RAM offsets.
+*/
+#define PROFF_SCC1	((uint)0x0000)
+#define PROFF_IIC	((uint)0x0080)
+#define PROFF_SCC2	((uint)0x0100)
+#define PROFF_SCC3	((uint)0x0200)
+#define PROFF_SMC1	((uint)0x0280)
+#define PROFF_SCC4	((uint)0x0300)
+#define PROFF_SMC2	((uint)0x0380)
+
+/* Define enough so I can at least use the serial port as a UART.
+ * The MBX uses SMC1 as the host serial port.
+ */
+typedef struct smc_uart {
+	ushort	smc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	smc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	smc_rfcr;	/* Rx function code */
+	u_char	smc_tfcr;	/* Tx function code */
+	ushort	smc_mrblr;	/* Max receive buffer length */
+	uint	smc_rstate;	/* Internal */
+	uint	smc_idp;	/* Internal */
+	ushort	smc_rbptr;	/* Internal */
+	ushort	smc_ibc;	/* Internal */
+	uint	smc_rxtmp;	/* Internal */
+	uint	smc_tstate;	/* Internal */
+	uint	smc_tdp;	/* Internal */
+	ushort	smc_tbptr;	/* Internal */
+	ushort	smc_tbc;	/* Internal */
+	uint	smc_txtmp;	/* Internal */
+	ushort	smc_maxidl;	/* Maximum idle characters */
+	ushort	smc_tmpidl;	/* Temporary idle counter */
+	ushort	smc_brklen;	/* Last received break length */
+	ushort	smc_brkec;	/* rcv'd break condition counter */
+	ushort	smc_brkcr;	/* xmt break count register */
+	ushort	smc_rmask;	/* Temporary bit mask */
+} smc_uart_t;
+
+/* Function code bits.
+*/
+#define SMC_EB	((u_char)0x10)	/* Set big endian byte order */
+
+/* SMC uart mode register.
+*/
+#define	SMCMR_REN	((ushort)0x0001)
+#define SMCMR_TEN	((ushort)0x0002)
+#define SMCMR_DM	((ushort)0x000c)
+#define SMCMR_SM_GCI	((ushort)0x0000)
+#define SMCMR_SM_UART	((ushort)0x0020)
+#define SMCMR_SM_TRANS	((ushort)0x0030)
+#define SMCMR_SM_MASK	((ushort)0x0030)
+#define SMCMR_PM_EVEN	((ushort)0x0100)	/* Even parity, else odd */
+#define SMCMR_REVD	SMCMR_PM_EVEN
+#define SMCMR_PEN	((ushort)0x0200)	/* Parity enable */
+#define SMCMR_BS	SMCMR_PEN
+#define SMCMR_SL	((ushort)0x0400)	/* Two stops, else one */
+#define SMCR_CLEN_MASK	((ushort)0x7800)	/* Character length */
+#define smcr_mk_clen(C)	(((C) << 11) & SMCR_CLEN_MASK)
+
+/* SMC2 as Centronics parallel printer.  It is half duplex, in that
+ * it can only receive or transmit.  The parameter ram values for
+ * each direction are either unique or properly overlap, so we can
+ * include them in one structure.
+ */
+typedef struct smc_centronics {
+	ushort	scent_rbase;
+	ushort	scent_tbase;
+	u_char	scent_cfcr;
+	u_char	scent_smask;
+	ushort	scent_mrblr;
+	uint	scent_rstate;
+	uint	scent_r_ptr;
+	ushort	scent_rbptr;
+	ushort	scent_r_cnt;
+	uint	scent_rtemp;
+	uint	scent_tstate;
+	uint	scent_t_ptr;
+	ushort	scent_tbptr;
+	ushort	scent_t_cnt;
+	uint	scent_ttemp;
+	ushort	scent_max_sl;
+	ushort	scent_sl_cnt;
+	ushort	scent_character1;
+	ushort	scent_character2;
+	ushort	scent_character3;
+	ushort	scent_character4;
+	ushort	scent_character5;
+	ushort	scent_character6;
+	ushort	scent_character7;
+	ushort	scent_character8;
+	ushort	scent_rccm;
+	ushort	scent_rccr;
+} smc_cent_t;
+
+/* Centronics Status Mask Register.
+*/
+#define SMC_CENT_F	((u_char)0x08)
+#define SMC_CENT_PE	((u_char)0x04)
+#define SMC_CENT_S	((u_char)0x02)
+
+/* SMC Event and Mask register.
+*/
+#define	SMCM_BRKE	((unsigned char)0x40)	/* When in UART Mode */
+#define	SMCM_BRK	((unsigned char)0x10)	/* When in UART Mode */
+#define	SMCM_TXE	((unsigned char)0x10)	/* When in Transparent Mode */
+#define	SMCM_BSY	((unsigned char)0x04)
+#define	SMCM_TX		((unsigned char)0x02)
+#define	SMCM_RX		((unsigned char)0x01)
+
+/* Baud rate generators.
+*/
+#define CPM_BRG_RST		((uint)0x00020000)
+#define CPM_BRG_EN		((uint)0x00010000)
+#define CPM_BRG_EXTC_INT	((uint)0x00000000)
+#define CPM_BRG_EXTC_CLK2	((uint)0x00004000)
+#define CPM_BRG_EXTC_CLK6	((uint)0x00008000)
+#define CPM_BRG_ATB		((uint)0x00002000)
+#define CPM_BRG_CD_MASK		((uint)0x00001ffe)
+#define CPM_BRG_DIV16		((uint)0x00000001)
+
+/* SCCs.
+*/
+#define SCC_GSMRH_IRP		((uint)0x00040000)
+#define SCC_GSMRH_GDE		((uint)0x00010000)
+#define SCC_GSMRH_TCRC_CCITT	((uint)0x00008000)
+#define SCC_GSMRH_TCRC_BISYNC	((uint)0x00004000)
+#define SCC_GSMRH_TCRC_HDLC	((uint)0x00000000)
+#define SCC_GSMRH_REVD		((uint)0x00002000)
+#define SCC_GSMRH_TRX		((uint)0x00001000)
+#define SCC_GSMRH_TTX		((uint)0x00000800)
+#define SCC_GSMRH_CDP		((uint)0x00000400)
+#define SCC_GSMRH_CTSP		((uint)0x00000200)
+#define SCC_GSMRH_CDS		((uint)0x00000100)
+#define SCC_GSMRH_CTSS		((uint)0x00000080)
+#define SCC_GSMRH_TFL		((uint)0x00000040)
+#define SCC_GSMRH_RFW		((uint)0x00000020)
+#define SCC_GSMRH_TXSY		((uint)0x00000010)
+#define SCC_GSMRH_SYNL16	((uint)0x0000000c)
+#define SCC_GSMRH_SYNL8		((uint)0x00000008)
+#define SCC_GSMRH_SYNL4		((uint)0x00000004)
+#define SCC_GSMRH_RTSM		((uint)0x00000002)
+#define SCC_GSMRH_RSYN		((uint)0x00000001)
+
+#define SCC_GSMRL_SIR		((uint)0x80000000)	/* SCC2 only */
+#define SCC_GSMRL_EDGE_NONE	((uint)0x60000000)
+#define SCC_GSMRL_EDGE_NEG	((uint)0x40000000)
+#define SCC_GSMRL_EDGE_POS	((uint)0x20000000)
+#define SCC_GSMRL_EDGE_BOTH	((uint)0x00000000)
+#define SCC_GSMRL_TCI		((uint)0x10000000)
+#define SCC_GSMRL_TSNC_3	((uint)0x0c000000)
+#define SCC_GSMRL_TSNC_4	((uint)0x08000000)
+#define SCC_GSMRL_TSNC_14	((uint)0x04000000)
+#define SCC_GSMRL_TSNC_INF	((uint)0x00000000)
+#define SCC_GSMRL_RINV		((uint)0x02000000)
+#define SCC_GSMRL_TINV		((uint)0x01000000)
+#define SCC_GSMRL_TPL_128	((uint)0x00c00000)
+#define SCC_GSMRL_TPL_64	((uint)0x00a00000)
+#define SCC_GSMRL_TPL_48	((uint)0x00800000)
+#define SCC_GSMRL_TPL_32	((uint)0x00600000)
+#define SCC_GSMRL_TPL_16	((uint)0x00400000)
+#define SCC_GSMRL_TPL_8		((uint)0x00200000)
+#define SCC_GSMRL_TPL_NONE	((uint)0x00000000)
+#define SCC_GSMRL_TPP_ALL1	((uint)0x00180000)
+#define SCC_GSMRL_TPP_01	((uint)0x00100000)
+#define SCC_GSMRL_TPP_10	((uint)0x00080000)
+#define SCC_GSMRL_TPP_ZEROS	((uint)0x00000000)
+#define SCC_GSMRL_TEND		((uint)0x00040000)
+#define SCC_GSMRL_TDCR_32	((uint)0x00030000)
+#define SCC_GSMRL_TDCR_16	((uint)0x00020000)
+#define SCC_GSMRL_TDCR_8	((uint)0x00010000)
+#define SCC_GSMRL_TDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RDCR_32	((uint)0x0000c000)
+#define SCC_GSMRL_RDCR_16	((uint)0x00008000)
+#define SCC_GSMRL_RDCR_8	((uint)0x00004000)
+#define SCC_GSMRL_RDCR_1	((uint)0x00000000)
+#define SCC_GSMRL_RENC_DFMAN	((uint)0x00003000)
+#define SCC_GSMRL_RENC_MANCH	((uint)0x00002000)
+#define SCC_GSMRL_RENC_FM0	((uint)0x00001000)
+#define SCC_GSMRL_RENC_NRZI	((uint)0x00000800)
+#define SCC_GSMRL_RENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_TENC_DFMAN	((uint)0x00000600)
+#define SCC_GSMRL_TENC_MANCH	((uint)0x00000400)
+#define SCC_GSMRL_TENC_FM0	((uint)0x00000200)
+#define SCC_GSMRL_TENC_NRZI	((uint)0x00000100)
+#define SCC_GSMRL_TENC_NRZ	((uint)0x00000000)
+#define SCC_GSMRL_DIAG_LE	((uint)0x000000c0)	/* Loop and echo */
+#define SCC_GSMRL_DIAG_ECHO	((uint)0x00000080)
+#define SCC_GSMRL_DIAG_LOOP	((uint)0x00000040)
+#define SCC_GSMRL_DIAG_NORM	((uint)0x00000000)
+#define SCC_GSMRL_ENR		((uint)0x00000020)
+#define SCC_GSMRL_ENT		((uint)0x00000010)
+#define SCC_GSMRL_MODE_ENET	((uint)0x0000000c)
+#define SCC_GSMRL_MODE_DDCMP	((uint)0x00000009)
+#define SCC_GSMRL_MODE_BISYNC	((uint)0x00000008)
+#define SCC_GSMRL_MODE_V14	((uint)0x00000007)
+#define SCC_GSMRL_MODE_AHDLC	((uint)0x00000006)
+#define SCC_GSMRL_MODE_PROFIBUS	((uint)0x00000005)
+#define SCC_GSMRL_MODE_UART	((uint)0x00000004)
+#define SCC_GSMRL_MODE_SS7	((uint)0x00000003)
+#define SCC_GSMRL_MODE_ATALK	((uint)0x00000002)
+#define SCC_GSMRL_MODE_HDLC	((uint)0x00000000)
+
+#define SCC_TODR_TOD		((ushort)0x8000)
+
+/* SCC Event and Mask register.
+*/
+#define	SCCM_TXE	((unsigned char)0x10)
+#define	SCCM_BSY	((unsigned char)0x04)
+#define	SCCM_TX		((unsigned char)0x02)
+#define	SCCM_RX		((unsigned char)0x01)
+
+typedef struct scc_param {
+	ushort	scc_rbase;	/* Rx Buffer descriptor base address */
+	ushort	scc_tbase;	/* Tx Buffer descriptor base address */
+	u_char	scc_rfcr;	/* Rx function code */
+	u_char	scc_tfcr;	/* Tx function code */
+	ushort	scc_mrblr;	/* Max receive buffer length */
+	uint	scc_rstate;	/* Internal */
+	uint	scc_idp;	/* Internal */
+	ushort	scc_rbptr;	/* Internal */
+	ushort	scc_ibc;	/* Internal */
+	uint	scc_rxtmp;	/* Internal */
+	uint	scc_tstate;	/* Internal */
+	uint	scc_tdp;	/* Internal */
+	ushort	scc_tbptr;	/* Internal */
+	ushort	scc_tbc;	/* Internal */
+	uint	scc_txtmp;	/* Internal */
+	uint	scc_rcrc;	/* Internal */
+	uint	scc_tcrc;	/* Internal */
+} sccp_t;
+
+/* Function code bits.
+*/
+#define SCC_EB	((u_char)0x10)	/* Set big endian byte order */
+
+/* CPM Ethernet through SCCx.
+ */
+typedef struct scc_enet {
+	sccp_t	sen_genscc;
+	uint	sen_cpres;	/* Preset CRC */
+	uint	sen_cmask;	/* Constant mask for CRC */
+	uint	sen_crcec;	/* CRC Error counter */
+	uint	sen_alec;	/* alignment error counter */
+	uint	sen_disfc;	/* discard frame counter */
+	ushort	sen_pads;	/* Tx short frame pad character */
+	ushort	sen_retlim;	/* Retry limit threshold */
+	ushort	sen_retcnt;	/* Retry limit counter */
+	ushort	sen_maxflr;	/* maximum frame length register */
+	ushort	sen_minflr;	/* minimum frame length register */
+	ushort	sen_maxd1;	/* maximum DMA1 length */
+	ushort	sen_maxd2;	/* maximum DMA2 length */
+	ushort	sen_maxd;	/* Rx max DMA */
+	ushort	sen_dmacnt;	/* Rx DMA counter */
+	ushort	sen_maxb;	/* Max BD byte count */
+	ushort	sen_gaddr1;	/* Group address filter */
+	ushort	sen_gaddr2;
+	ushort	sen_gaddr3;
+	ushort	sen_gaddr4;
+	uint	sen_tbuf0data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf0data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf0rba;	/* Internal */
+	uint	sen_tbuf0crc;	/* Internal */
+	ushort	sen_tbuf0bcnt;	/* Internal */
+	ushort	sen_paddrh;	/* physical address (MSB) */
+	ushort	sen_paddrm;
+	ushort	sen_paddrl;	/* physical address (LSB) */
+	ushort	sen_pper;	/* persistence */
+	ushort	sen_rfbdptr;	/* Rx first BD pointer */
+	ushort	sen_tfbdptr;	/* Tx first BD pointer */
+	ushort	sen_tlbdptr;	/* Tx last BD pointer */
+	uint	sen_tbuf1data0;	/* Save area 0 - current frame */
+	uint	sen_tbuf1data1;	/* Save area 1 - current frame */
+	uint	sen_tbuf1rba;	/* Internal */
+	uint	sen_tbuf1crc;	/* Internal */
+	ushort	sen_tbuf1bcnt;	/* Internal */
+	ushort	sen_txlen;	/* Tx Frame length counter */
+	ushort	sen_iaddr1;	/* Individual address filter */
+	ushort	sen_iaddr2;
+	ushort	sen_iaddr3;
+	ushort	sen_iaddr4;
+	ushort	sen_boffcnt;	/* Backoff counter */
+
+	/* NOTE: Some versions of the manual have the following items
+	 * incorrectly documented.  Below is the proper order.
+	 */
+	ushort	sen_taddrh;	/* temp address (MSB) */
+	ushort	sen_taddrm;
+	ushort	sen_taddrl;	/* temp address (LSB) */
+} scc_enet_t;
+
+/***  MBX  ************************************************************/
+
+#ifdef CONFIG_MBX
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.  The TCLK and RCLK seem unique
+ * to the MBX860 board.  Any two of the four available clocks could be
+ * used, and the MPC860 cookbook manual has an example using different
+ * clock pins.
+ */
+#define PA_ENET_RXD	((ushort)0x0001)
+#define PA_ENET_TXD	((ushort)0x0002)
+#define PA_ENET_TCLK	((ushort)0x0200)
+#define PA_ENET_RCLK	((ushort)0x0800)
+#define PC_ENET_TENA	((ushort)0x0001)
+#define PC_ENET_CLSN	((ushort)0x0010)
+#define PC_ENET_RENA	((ushort)0x0020)
+
+/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
+ * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x000000ff)
+#define SICR_ENET_CLKRT	((uint)0x0000003d)
+#endif	/* CONFIG_MBX */
+
+/***  RPXLITE  ********************************************************/
+
+#ifdef CONFIG_RPXLITE
+/* This ENET stuff is for the MPC850 with ethernet on SCC2.  Some of
+ * this may be unique to the RPX-Lite configuration.
+ * Note TENA is on Port B.
+ */
+#define PA_ENET_RXD	((ushort)0x0004)
+#define PA_ENET_TXD	((ushort)0x0008)
+#define PA_ENET_TCLK	((ushort)0x0200)
+#define PA_ENET_RCLK	((ushort)0x0800)
+#define PB_ENET_TENA	((uint)0x00002000)
+#define PC_ENET_CLSN	((ushort)0x0040)
+#define PC_ENET_RENA	((ushort)0x0080)
+
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00003d00)
+#endif	/* CONFIG_RPXLITE */
+
+/***  BSEIP  **********************************************************/
+
+#ifdef CONFIG_BSEIP
+/* This ENET stuff is for the MPC823 with ethernet on SCC2.
+ * This is unique to the BSE ip-Engine board.
+ */
+#define PA_ENET_RXD	((ushort)0x0004)
+#define PA_ENET_TXD	((ushort)0x0008)
+#define PA_ENET_TCLK	((ushort)0x0100)
+#define PA_ENET_RCLK	((ushort)0x0200)
+#define PB_ENET_TENA	((uint)0x00002000)
+#define PC_ENET_CLSN	((ushort)0x0040)
+#define PC_ENET_RENA	((ushort)0x0080)
+
+/* BSE uses port B and C bits for PHY control also.
+*/
+#define PB_BSE_POWERUP	((uint)0x00000004)
+#define PB_BSE_FDXDIS	((uint)0x00008000)
+#define PC_BSE_LOOPBACK	((ushort)0x0800)
+
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002c00)
+#endif	/* CONFIG_BSEIP */
+
+/***  RPXCLASSIC  *****************************************************/
+
+#ifdef CONFIG_RPXCLASSIC
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PA_ENET_RXD	((ushort)0x0001)
+#define PA_ENET_TXD	((ushort)0x0002)
+#define PA_ENET_TCLK	((ushort)0x0200)
+#define PA_ENET_RCLK	((ushort)0x0800)
+#define PB_ENET_TENA	((uint)0x00001000)
+#define PC_ENET_CLSN	((ushort)0x0010)
+#define PC_ENET_RENA	((ushort)0x0020)
+
+/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
+ * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x000000ff)
+#define SICR_ENET_CLKRT	((uint)0x0000003d)
+#endif	/* CONFIG_RPXCLASSIC */
+
+/***  TQM823L, TQM850L  ***********************************************/
+
+#if defined(CONFIG_TQM823L) || defined(CONFIG_TQM850L)
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
+#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
+#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
+
+#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
+#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002600)
+#endif	/* CONFIG_TQM823L, CONFIG_TQM850L */
+
+/***  FPS850L  *********************************************************/
+
+#ifdef CONFIG_FPS850L
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
+#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
+#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PC_ENET_TENA	((ushort)0x0002)	/* PC 14 */
+#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
+#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
+
+/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
+ * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002600)
+#endif	/* CONFIG_FPS850L */
+
+/***  TQM860L  ********************************************************/
+
+#ifdef CONFIG_TQM860L
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC1 use.
+ */
+#define PA_ENET_RXD	((ushort)0x0001)	/* PA 15 */
+#define PA_ENET_TXD	((ushort)0x0002)	/* PA 14 */
+#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PC_ENET_TENA	((ushort)0x0001)	/* PC 15 */
+#define PC_ENET_CLSN	((ushort)0x0010)	/* PC 11 */
+#define PC_ENET_RENA	((ushort)0x0020)	/* PC 10 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC1.  Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x000000ff)
+#define SICR_ENET_CLKRT	((uint)0x00000026)
+#endif	/* CONFIG_TQM860L */
+
+/***  SPD823TS  *******************************************************/
+
+#ifdef CONFIG_SPD823TS
+/* Bits in parallel I/O port registers that have to be set/cleared
+ * to configure the pins for SCC2 use.
+ */
+#define PA_ENET_MDC	((ushort)0x0001)	/* PA 15 !!! */
+#define PA_ENET_MDIO	((ushort)0x0002)	/* PA 14 !!! */
+#define PA_ENET_RXD	((ushort)0x0004)	/* PA 13 */
+#define PA_ENET_TXD	((ushort)0x0008)	/* PA 12 */
+#define PA_ENET_RCLK	((ushort)0x0200)	/* PA  6 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PB_ENET_TENA	((uint)0x00002000)	/* PB 18 */
+
+#define PC_ENET_CLSN	((ushort)0x0040)	/* PC  9 */
+#define PC_ENET_RENA	((ushort)0x0080)	/* PC  8 */
+#define	PC_ENET_RESET	((ushort)0x0100)	/* PC  7 !!! */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
+ * SCC2.  Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x0000ff00)
+#define SICR_ENET_CLKRT	((uint)0x00002E00)
+#endif	/* CONFIG_SPD823TS */
+
+
+/***  SM850  *********************************************************/
+
+/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
+
+#ifdef CONFIG_SM850
+#define PB_ENET_RXD	((uint)0x00000004)	/* PB 29 */
+#define PB_ENET_TXD	((uint)0x00000002)	/* PB 30 */
+#define PA_ENET_RCLK	((ushort)0x0100)	/* PA  7 */
+#define PA_ENET_TCLK	((ushort)0x0400)	/* PA  5 */
+
+#define PC_ENET_LBK	((ushort)0x0008)	/* PC 12 */
+#define PC_ENET_TENA	((ushort)0x0004)	/* PC 13 */
+
+#define PC_ENET_RENA	((ushort)0x0800)	/* PC  4 */
+#define PC_ENET_CLSN	((ushort)0x0400)	/* PC  5 */
+
+/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
+ * SCC3.  Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
+ */
+#define SICR_ENET_MASK	((uint)0x00FF0000)
+#define SICR_ENET_CLKRT	((uint)0x00260000)
+#endif	/* CONFIG_SM850 */
+
+/*********************************************************************/
+
+/* SCC Event register as used by Ethernet.
+*/
+#define SCCE_ENET_GRA	((ushort)0x0080)	/* Graceful stop complete */
+#define SCCE_ENET_TXE	((ushort)0x0010)	/* Transmit Error */
+#define SCCE_ENET_RXF	((ushort)0x0008)	/* Full frame received */
+#define SCCE_ENET_BSY	((ushort)0x0004)	/* All incoming buffers full */
+#define SCCE_ENET_TXB	((ushort)0x0002)	/* A buffer was transmitted */
+#define SCCE_ENET_RXB	((ushort)0x0001)	/* A buffer was received */
+
+/* SCC Mode Register (PMSR) as used by Ethernet.
+*/
+#define SCC_PMSR_HBC	((ushort)0x8000)	/* Enable heartbeat */
+#define SCC_PMSR_FC	((ushort)0x4000)	/* Force collision */
+#define SCC_PMSR_RSH	((ushort)0x2000)	/* Receive short frames */
+#define SCC_PMSR_IAM	((ushort)0x1000)	/* Check individual hash */
+#define SCC_PMSR_ENCRC	((ushort)0x0800)	/* Ethernet CRC mode */
+#define SCC_PMSR_PRO	((ushort)0x0200)	/* Promiscuous mode */
+#define SCC_PMSR_BRO	((ushort)0x0100)	/* Catch broadcast pkts */
+#define SCC_PMSR_SBT	((ushort)0x0080)	/* Special backoff timer */
+#define SCC_PMSR_LPB	((ushort)0x0040)	/* Set Loopback mode */
+#define SCC_PMSR_SIP	((ushort)0x0020)	/* Sample Input Pins */
+#define SCC_PMSR_LCW	((ushort)0x0010)	/* Late collision window */
+#define SCC_PMSR_NIB22	((ushort)0x000a)	/* Start frame search */
+#define SCC_PMSR_FDE	((ushort)0x0001)	/* Full duplex enable */
+
+/* Buffer descriptor control/status used by Ethernet receive.
+*/
+#define BD_ENET_RX_EMPTY	((ushort)0x8000)
+#define BD_ENET_RX_WRAP		((ushort)0x2000)
+#define BD_ENET_RX_INTR		((ushort)0x1000)
+#define BD_ENET_RX_LAST		((ushort)0x0800)
+#define BD_ENET_RX_FIRST	((ushort)0x0400)
+#define BD_ENET_RX_MISS		((ushort)0x0100)
+#define BD_ENET_RX_LG		((ushort)0x0020)
+#define BD_ENET_RX_NO		((ushort)0x0010)
+#define BD_ENET_RX_SH		((ushort)0x0008)
+#define BD_ENET_RX_CR		((ushort)0x0004)
+#define BD_ENET_RX_OV		((ushort)0x0002)
+#define BD_ENET_RX_CL		((ushort)0x0001)
+#define BD_ENET_RX_STATS	((ushort)0x013f)	/* All status bits */
+
+/* Buffer descriptor control/status used by Ethernet transmit.
+*/
+#define BD_ENET_TX_READY	((ushort)0x8000)
+#define BD_ENET_TX_PAD		((ushort)0x4000)
+#define BD_ENET_TX_WRAP		((ushort)0x2000)
+#define BD_ENET_TX_INTR		((ushort)0x1000)
+#define BD_ENET_TX_LAST		((ushort)0x0800)
+#define BD_ENET_TX_TC		((ushort)0x0400)
+#define BD_ENET_TX_DEF		((ushort)0x0200)
+#define BD_ENET_TX_HB		((ushort)0x0100)
+#define BD_ENET_TX_LC		((ushort)0x0080)
+#define BD_ENET_TX_RL		((ushort)0x0040)
+#define BD_ENET_TX_RCMASK	((ushort)0x003c)
+#define BD_ENET_TX_UN		((ushort)0x0002)
+#define BD_ENET_TX_CSL		((ushort)0x0001)
+#define BD_ENET_TX_STATS	((ushort)0x03ff)	/* All status bits */
+
+/* SCC as UART
+*/
+typedef struct scc_uart {
+	sccp_t	scc_genscc;
+	uint	scc_res1;	/* Reserved */
+	uint	scc_res2;	/* Reserved */
+	ushort	scc_maxidl;	/* Maximum idle chars */
+	ushort	scc_idlc;	/* temp idle counter */
+	ushort	scc_brkcr;	/* Break count register */
+	ushort	scc_parec;	/* receive parity error counter */
+	ushort	scc_frmec;	/* receive framing error counter */
+	ushort	scc_nosec;	/* receive noise counter */
+	ushort	scc_brkec;	/* receive break condition counter */
+	ushort	scc_brkln;	/* last received break length */
+	ushort	scc_uaddr1;	/* UART address character 1 */
+	ushort	scc_uaddr2;	/* UART address character 2 */
+	ushort	scc_rtemp;	/* Temp storage */
+	ushort	scc_toseq;	/* Transmit out of sequence char */
+	ushort	scc_char1;	/* control character 1 */
+	ushort	scc_char2;	/* control character 2 */
+	ushort	scc_char3;	/* control character 3 */
+	ushort	scc_char4;	/* control character 4 */
+	ushort	scc_char5;	/* control character 5 */
+	ushort	scc_char6;	/* control character 6 */
+	ushort	scc_char7;	/* control character 7 */
+	ushort	scc_char8;	/* control character 8 */
+	ushort	scc_rccm;	/* receive control character mask */
+	ushort	scc_rccr;	/* receive control character register */
+	ushort	scc_rlbc;	/* receive last break character */
+} scc_uart_t;
+
+/* SCC Event and Mask registers when it is used as a UART.
+*/
+#define UART_SCCM_GLR		((ushort)0x1000)
+#define UART_SCCM_GLT		((ushort)0x0800)
+#define UART_SCCM_AB		((ushort)0x0200)
+#define UART_SCCM_IDL		((ushort)0x0100)
+#define UART_SCCM_GRA		((ushort)0x0080)
+#define UART_SCCM_BRKE		((ushort)0x0040)
+#define UART_SCCM_BRKS		((ushort)0x0020)
+#define UART_SCCM_CCR		((ushort)0x0008)
+#define UART_SCCM_BSY		((ushort)0x0004)
+#define UART_SCCM_TX		((ushort)0x0002)
+#define UART_SCCM_RX		((ushort)0x0001)
+
+/* The SCC PMSR when used as a UART.
+*/
+#define SCU_PMSR_FLC		((ushort)0x8000)
+#define SCU_PMSR_SL		((ushort)0x4000)
+#define SCU_PMSR_CL		((ushort)0x3000)
+#define SCU_PMSR_UM		((ushort)0x0c00)
+#define SCU_PMSR_FRZ		((ushort)0x0200)
+#define SCU_PMSR_RZS		((ushort)0x0100)
+#define SCU_PMSR_SYN		((ushort)0x0080)
+#define SCU_PMSR_DRT		((ushort)0x0040)
+#define SCU_PMSR_PEN		((ushort)0x0010)
+#define SCU_PMSR_RPM		((ushort)0x000c)
+#define SCU_PMSR_REVP		((ushort)0x0008)
+#define SCU_PMSR_TPM		((ushort)0x0003)
+#define SCU_PMSR_TEVP		((ushort)0x0002)
+
+/* CPM Transparent mode SCC.
+ */
+typedef struct scc_trans {
+	sccp_t	st_genscc;
+	uint	st_cpres;	/* Preset CRC */
+	uint	st_cmask;	/* Constant mask for CRC */
+} scc_trans_t;
+
+#define BD_SCC_TX_LAST		((ushort)0x0800)
+
+/* IIC parameter RAM.
+*/
+typedef struct iic {
+	ushort	iic_rbase;	/* Rx Buffer descriptor base address */
+	ushort	iic_tbase;	/* Tx Buffer descriptor base address */
+	u_char	iic_rfcr;	/* Rx function code */
+	u_char	iic_tfcr;	/* Tx function code */
+	ushort	iic_mrblr;	/* Max receive buffer length */
+	uint	iic_rstate;	/* Internal */
+	uint	iic_rdp;	/* Internal */
+	ushort	iic_rbptr;	/* Internal */
+	ushort	iic_rbc;	/* Internal */
+	uint	iic_rxtmp;	/* Internal */
+	uint	iic_tstate;	/* Internal */
+	uint	iic_tdp;	/* Internal */
+	ushort	iic_tbptr;	/* Internal */
+	ushort	iic_tbc;	/* Internal */
+	uint	iic_txtmp;	/* Internal */
+} iic_t;
+
+#define BD_IIC_START		((ushort)0x0400)
+
+/* CPM interrupts.  There are nearly 32 interrupts generated by CPM
+ * channels or devices.  All of these are presented to the PPC core
+ * as a single interrupt.  The CPM interrupt handler dispatches its
+ * own handlers, in a similar fashion to the PPC core handler.  We
+ * use the table as defined in the manuals (i.e. no special high
+ * priority and SCC1 == SCCa, etc...).
+ */
+#define CPMVEC_NR		32
+#define	CPMVEC_PIO_PC15		((ushort)0x1f)
+#define	CPMVEC_SCC1		((ushort)0x1e)
+#define	CPMVEC_SCC2		((ushort)0x1d)
+#define	CPMVEC_SCC3		((ushort)0x1c)
+#define	CPMVEC_SCC4		((ushort)0x1b)
+#define	CPMVEC_PIO_PC14		((ushort)0x1a)
+#define	CPMVEC_TIMER1		((ushort)0x19)
+#define	CPMVEC_PIO_PC13		((ushort)0x18)
+#define	CPMVEC_PIO_PC12		((ushort)0x17)
+#define	CPMVEC_SDMA_CB_ERR	((ushort)0x16)
+#define CPMVEC_IDMA1		((ushort)0x15)
+#define CPMVEC_IDMA2		((ushort)0x14)
+#define CPMVEC_TIMER2		((ushort)0x12)
+#define CPMVEC_RISCTIMER	((ushort)0x11)
+#define CPMVEC_I2C		((ushort)0x10)
+#define	CPMVEC_PIO_PC11		((ushort)0x0f)
+#define	CPMVEC_PIO_PC10		((ushort)0x0e)
+#define CPMVEC_TIMER3		((ushort)0x0c)
+#define	CPMVEC_PIO_PC9		((ushort)0x0b)
+#define	CPMVEC_PIO_PC8		((ushort)0x0a)
+#define	CPMVEC_PIO_PC7		((ushort)0x09)
+#define CPMVEC_TIMER4		((ushort)0x07)
+#define	CPMVEC_PIO_PC6		((ushort)0x06)
+#define	CPMVEC_SPI		((ushort)0x05)
+#define	CPMVEC_SMC1		((ushort)0x04)
+#define	CPMVEC_SMC2		((ushort)0x03)
+#define	CPMVEC_PIO_PC5		((ushort)0x02)
+#define	CPMVEC_PIO_PC4		((ushort)0x01)
+#define	CPMVEC_ERROR		((ushort)0x00)
+
+/* CPM interrupt configuration vector.
+*/
+#define	CICR_SCD_SCC4		((uint)0x00c00000)	/* SCC4 @ SCCd */
+#define	CICR_SCC_SCC3		((uint)0x00200000)	/* SCC3 @ SCCc */
+#define	CICR_SCB_SCC2		((uint)0x00040000)	/* SCC2 @ SCCb */
+#define	CICR_SCA_SCC1		((uint)0x00000000)	/* SCC1 @ SCCa */
+#define CICR_IRL_MASK		((uint)0x0000e000)	/* Core interrrupt */
+#define CICR_HP_MASK		((uint)0x00001f00)	/* Hi-pri int. */
+#define CICR_IEN		((uint)0x00000080)	/* Int. enable */
+#define CICR_SPS		((uint)0x00000001)	/* SCC Spread */
+
+extern void cpm_install_handler(int vec, 
+		void (*handler)(void *, struct pt_regs *regs), void *dev_id);
+extern void cpm_free_handler(int vec);
+
+#endif /* __CPM_8XX__ */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)