patch-2.4.11-dontuse linux/drivers/ide/ide-m8xx.c

Next file: linux/drivers/ide/ide-pci.c
Previous file: linux/drivers/ide/ide-floppy.c
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.4.10/linux/drivers/ide/ide-m8xx.c linux/drivers/ide/ide-m8xx.c
@@ -0,0 +1,851 @@
+/*
+ *
+ *
+ *  linux/drivers/ide/ide-m8xx.c
+ *
+ */
+
+#include <linux/config.h>
+#include <linux/errno.h>
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/stddef.h>
+#include <linux/unistd.h>
+#include <linux/ptrace.h>
+#include <linux/slab.h>
+#include <linux/user.h>
+#include <linux/a.out.h>
+#include <linux/tty.h>
+#include <linux/major.h>
+#include <linux/interrupt.h>
+#include <linux/reboot.h>
+#include <linux/init.h>
+#include <linux/blk.h>
+#include <linux/ioport.h>
+#include <linux/ide.h>
+#include <linux/bootmem.h>
+
+#include <asm/mpc8xx.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/residual.h>
+#include <asm/io.h>
+#include <asm/pgtable.h>
+#include <asm/ide.h>
+#include <asm/8xx_immap.h>
+#include <asm/machdep.h>
+#include <asm/irq.h>
+
+#include "ide_modes.h"
+static int identify  (volatile unsigned char *p);
+static void print_fixed (volatile unsigned char *p);
+static void print_funcid (int func);
+static int check_ide_device (unsigned long base);
+
+static void ide_interrupt_ack (void *dev);
+static void m8xx_ide_tuneproc(ide_drive_t *drive, byte pio);
+
+typedef	struct ide_ioport_desc {
+	unsigned long	base_off;		/* Offset to PCMCIA memory	*/
+	ide_ioreg_t	reg_off[IDE_NR_PORTS];	/* controller register offsets	*/
+	int		irq;			/* IRQ				*/
+} ide_ioport_desc_t;
+
+ide_ioport_desc_t ioport_dsc[MAX_HWIFS] = {
+#ifdef IDE0_BASE_OFFSET
+	{ IDE0_BASE_OFFSET,
+	    {
+		IDE0_DATA_REG_OFFSET,
+		IDE0_ERROR_REG_OFFSET,
+		IDE0_NSECTOR_REG_OFFSET,
+		IDE0_SECTOR_REG_OFFSET,
+		IDE0_LCYL_REG_OFFSET,
+		IDE0_HCYL_REG_OFFSET,
+		IDE0_SELECT_REG_OFFSET,
+		IDE0_STATUS_REG_OFFSET,
+		IDE0_CONTROL_REG_OFFSET,
+		IDE0_IRQ_REG_OFFSET,
+	    },
+	    IDE0_INTERRUPT,
+	},
+#ifdef IDE1_BASE_OFFSET
+	{ IDE1_BASE_OFFSET,
+	    {
+		IDE1_DATA_REG_OFFSET,
+		IDE1_ERROR_REG_OFFSET,
+		IDE1_NSECTOR_REG_OFFSET,
+		IDE1_SECTOR_REG_OFFSET,
+		IDE1_LCYL_REG_OFFSET,
+		IDE1_HCYL_REG_OFFSET,
+		IDE1_SELECT_REG_OFFSET,
+		IDE1_STATUS_REG_OFFSET,
+		IDE1_CONTROL_REG_OFFSET,
+		IDE1_IRQ_REG_OFFSET,
+	    },
+	    IDE1_INTERRUPT,
+	},
+#endif /* IDE1_BASE_OFFSET */
+#endif	/* IDE0_BASE_OFFSET */
+};
+
+ide_pio_timings_t ide_pio_clocks[6];
+int hold_time[6] =  {30, 20, 15, 10, 10, 10 };   /* PIO Mode 5 with IORDY (nonstandard) */
+
+/*
+ * Warning: only 1 (ONE) PCMCIA slot supported here,
+ * which must be correctly initialized by the firmware (PPCBoot).
+ */
+static int _slot_ = -1;			/* will be read from PCMCIA registers   */
+
+/* Make clock cycles and always round up */
+#define PCMCIA_MK_CLKS( t, T ) (( (t) * ((T)/1000000) + 999U ) / 1000U )
+
+
+
+/*
+ * IDE stuff.
+ */
+static int
+m8xx_ide_default_irq(ide_ioreg_t base)
+{
+#ifdef CONFIG_BLK_DEV_MPC8xx_IDE
+	if (base >= MAX_HWIFS)
+		return 0;
+
+	printk("[%d] m8xx_ide_default_irq %d\n",__LINE__,ioport_dsc[base].irq);
+	
+	return (ioport_dsc[base].irq);
+#else
+        return 9;
+#endif
+}
+
+static ide_ioreg_t
+m8xx_ide_default_io_base(int index)
+{
+        return index;
+}
+
+#define M8XX_PCMCIA_CD2(slot)      (0x10000000 >> (slot << 4))
+#define M8XX_PCMCIA_CD1(slot)      (0x08000000 >> (slot << 4))
+
+/*
+ * The TQM850L hardware has two pins swapped! Grrrrgh!
+ */
+#ifdef	CONFIG_TQM850L
+#define __MY_PCMCIA_GCRX_CXRESET	PCMCIA_GCRX_CXOE
+#define __MY_PCMCIA_GCRX_CXOE		PCMCIA_GCRX_CXRESET
+#else
+#define __MY_PCMCIA_GCRX_CXRESET	PCMCIA_GCRX_CXRESET
+#define __MY_PCMCIA_GCRX_CXOE		PCMCIA_GCRX_CXOE
+#endif
+
+#if defined(CONFIG_BLK_DEV_MPC8xx_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define PCMCIA_SCHLVL IDE0_INTERRUPT	/* Status Change Interrupt Level	*/
+static int pcmcia_schlvl = PCMCIA_SCHLVL;
+#endif
+
+/*
+ * See include/linux/ide.h for definition of hw_regs_t (p, base)
+ */
+
+/*
+ * m8xx_ide_init_hwif_ports for a direct IDE interface _using_
+ */
+#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_IDE_8xx_DIRECT)
+static void
+m8xx_ide_init_hwif_ports(hw_regs_t *hw, ide_ioreg_t data_port, 
+		ide_ioreg_t ctrl_port, int *irq)
+{
+	ide_ioreg_t *p = hw->io_ports;
+	int i;
+
+	typedef struct {
+		ulong br;
+		ulong or;
+	} pcmcia_win_t;
+	volatile pcmcia_win_t *win;
+	volatile pcmconf8xx_t *pcmp;
+
+	uint *pgcrx;
+	u32 pcmcia_phy_base;
+	u32 pcmcia_phy_end;
+	static unsigned long pcmcia_base = 0;
+	unsigned long base;
+
+	*p = 0;
+	if (irq)
+		*irq = 0;
+
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)IMAP_ADDR)->im_pcmcia));
+
+	if (!pcmcia_base) {
+                /*
+                 * Read out PCMCIA registers. Since the reset values
+                 * are undefined, we sure hope that they have been
+                 * set up by firmware
+		 */
+
+		/* Scan all registers for valid settings */
+		pcmcia_phy_base = 0xFFFFFFFF;
+		pcmcia_phy_end = 0;
+		/* br0 is start of brX and orX regs */
+		win = (pcmcia_win_t *) \
+			(&(((immap_t *)IMAP_ADDR)->im_pcmcia.pcmc_pbr0));
+		for (i = 0; i < 8; i++) {
+			if (win->or & 1) {	/* This bank is marked as valid */
+				if (win->br < pcmcia_phy_base) {
+					pcmcia_phy_base = win->br;
+				}
+				if ((win->br + PCMCIA_MEM_SIZE) > pcmcia_phy_end) {
+					pcmcia_phy_end  = win->br + PCMCIA_MEM_SIZE;
+				}
+				/* Check which slot that has been defined */
+				_slot_ = (win->or >> 2) & 1;
+
+			}					/* Valid bank */
+			win++;
+		}						/* for */
+
+		printk ("PCMCIA slot %c: phys mem %08x...%08x (size %08x)\n",
+			'A' + _slot_,
+			pcmcia_phy_base, pcmcia_phy_end,
+			pcmcia_phy_end - pcmcia_phy_base);
+
+		pcmcia_base=(unsigned long)ioremap(pcmcia_phy_base,
+						   pcmcia_phy_end-pcmcia_phy_base);
+
+#ifdef DEBUG
+		printk ("PCMCIA virt base: %08lx\n", pcmcia_base);
+#endif
+		/* Compute clock cycles for PIO timings */
+		for (i=0; i<6; ++i) {
+			bd_t	*binfo = (bd_t *)__res;
+
+			hold_time[i]   =
+				PCMCIA_MK_CLKS (hold_time[i],
+						binfo->bi_busfreq);
+			ide_pio_clocks[i].setup_time  =
+				PCMCIA_MK_CLKS (ide_pio_timings[i].setup_time,
+						binfo->bi_busfreq);
+			ide_pio_clocks[i].active_time =
+				PCMCIA_MK_CLKS (ide_pio_timings[i].active_time,
+						binfo->bi_busfreq);
+			ide_pio_clocks[i].cycle_time  =
+				PCMCIA_MK_CLKS (ide_pio_timings[i].cycle_time,
+						binfo->bi_busfreq);
+#if 0
+			printk ("PIO mode %d timings: %d/%d/%d => %d/%d/%d\n",
+				i,
+				ide_pio_clocks[i].setup_time,
+				ide_pio_clocks[i].active_time,
+				ide_pio_clocks[i].hold_time,
+				ide_pio_clocks[i].cycle_time,
+				ide_pio_timings[i].setup_time,
+				ide_pio_timings[i].active_time,
+				ide_pio_timings[i].hold_time,
+				ide_pio_timings[i].cycle_time);
+#endif
+		}
+	}
+
+	if (data_port >= MAX_HWIFS)
+		return;
+
+	if (_slot_ == -1) {
+		printk ("PCMCIA slot has not been defined! Using A as default\n");
+		_slot_ = 0;
+	}
+
+#ifdef CONFIG_IDE_8xx_PCCARD
+
+#ifdef DEBUG
+	printk ("PIPR = 0x%08X  slot %c ==> mask = 0x%X\n",
+		pcmp->pcmc_pipr,
+		'A' + _slot_,
+		M8XX_PCMCIA_CD1(_slot_) | M8XX_PCMCIA_CD2(_slot_) );
+#endif /* DEBUG */
+
+	if (pcmp->pcmc_pipr & (M8XX_PCMCIA_CD1(_slot_)|M8XX_PCMCIA_CD2(_slot_))) {
+		printk ("No card in slot %c: PIPR=%08x\n",
+			'A' + _slot_, (u32) pcmp->pcmc_pipr);
+		return;		/* No card in slot */
+	}
+
+	check_ide_device (pcmcia_base);
+
+#endif	/* CONFIG_IDE_8xx_PCCARD */
+
+	base = pcmcia_base + ioport_dsc[data_port].base_off;
+#ifdef DEBUG
+	printk ("base: %08x + %08x = %08x\n",
+			pcmcia_base, ioport_dsc[data_port].base_off, base);
+#endif
+
+	for (i = 0; i < IDE_NR_PORTS; ++i) {
+#ifdef DEBUG
+		printk ("port[%d]: %08x + %08x = %08x\n",
+			i,
+			base,
+			ioport_dsc[data_port].reg_off[i],
+			i, base + ioport_dsc[data_port].reg_off[i]);
+#endif
+	 	*p++ = base + ioport_dsc[data_port].reg_off[i];
+	}
+
+	if (irq) {
+#ifdef CONFIG_IDE_8xx_PCCARD
+		unsigned int reg;
+
+		*irq = ioport_dsc[data_port].irq;
+		if (_slot_)
+			pgcrx = &((immap_t *) IMAP_ADDR)->im_pcmcia.pcmc_pgcrb;
+		else
+			pgcrx = &((immap_t *) IMAP_ADDR)->im_pcmcia.pcmc_pgcra;
+
+		reg = *pgcrx;
+		reg |= mk_int_int_mask (pcmcia_schlvl) << 24;
+		reg |= mk_int_int_mask (pcmcia_schlvl) << 16;
+		*pgcrx = reg;
+#else	/* direct connected IDE drive, i.e. external IRQ, not the PCMCIA irq */
+		*irq = ioport_dsc[data_port].irq;
+#endif	/* CONFIG_IDE_8xx_PCCARD */
+	}
+
+	/* register routine to tune PIO mode */
+	ide_hwifs[data_port].tuneproc = m8xx_ide_tuneproc;
+
+	hw->ack_intr = (ide_ack_intr_t *) ide_interrupt_ack;
+	/* Enable Harddisk Interrupt,
+	 * and make it edge sensitive
+	 */
+	/* (11-18) Set edge detect for irq, no wakeup from low power mode */
+	((immap_t *)IMAP_ADDR)->im_siu_conf.sc_siel |=
+					(0x80000000 >> ioport_dsc[data_port].irq);
+
+#ifdef CONFIG_IDE_8xx_PCCARD
+	/* Make sure we dont get garbage irq */
+	((immap_t *) IMAP_ADDR)->im_pcmcia.pcmc_pscr = 0xFFFF;
+
+	/* Enable falling edge irq */
+	pcmp->pcmc_per = 0x100000 >> (16 * _slot_);
+#endif	/* CONFIG_IDE_8xx_PCCARD */
+}	/* m8xx_ide_init_hwif_ports() using 8xx internal PCMCIA interface */
+#endif /* CONFIG_IDE_8xx_PCCARD || CONFIG_IDE_8xx_DIRECT */
+
+/*
+ * m8xx_ide_init_hwif_ports for a direct IDE interface _not_ using
+ * MPC8xx's internal PCMCIA interface
+ */
+#if defined(CONFIG_IDE_EXT_DIRECT)
+void m8xx_ide_init_hwif_ports (hw_regs_t *hw,
+	ide_ioreg_t data_port, ide_ioreg_t ctrl_port, int *irq)
+{
+	ide_ioreg_t *p = hw->io_ports;
+	int i;
+
+	u32 ide_phy_base;
+	u32 ide_phy_end;
+	static unsigned long ide_base = 0;
+	unsigned long base;
+
+	*p = 0;
+	if (irq)
+		*irq = 0;
+
+	if (!ide_base) {
+
+		/* TODO:
+		 * - add code to read ORx, BRx
+		 */
+		ide_phy_base = CFG_ATA_BASE_ADDR;
+		ide_phy_end  = CFG_ATA_BASE_ADDR + 0x200;
+
+		printk ("IDE phys mem : %08x...%08x (size %08x)\n",
+			ide_phy_base, ide_phy_end,
+			ide_phy_end - ide_phy_base);
+		
+		ide_base=(unsigned long)ioremap(ide_phy_base,
+						ide_phy_end-ide_phy_base);
+
+#ifdef DEBUG
+		printk ("IDE virt base: %08lx\n", ide_base);
+#endif
+	}
+
+	if (data_port >= MAX_HWIFS)
+		return;
+
+	base = ide_base + ioport_dsc[data_port].base_off;
+#ifdef DEBUG
+	printk ("base: %08x + %08x = %08x\n",
+		ide_base, ioport_dsc[data_port].base_off, base);
+#endif
+
+	for (i = 0; i < IDE_NR_PORTS; ++i) {
+#ifdef DEBUG
+		printk ("port[%d]: %08x + %08x = %08x\n",
+			i,
+			base,
+			ioport_dsc[data_port].reg_off[i],
+			i, base + ioport_dsc[data_port].reg_off[i]);
+#endif
+	 	*p++ = base + ioport_dsc[data_port].reg_off[i];
+	}
+
+	if (irq) {
+		/* direct connected IDE drive, i.e. external IRQ */
+		*irq = ioport_dsc[data_port].irq;
+	}
+
+	/* register routine to tune PIO mode */
+	ide_hwifs[data_port].tuneproc = m8xx_ide_tuneproc;
+
+	hw->ack_intr = (ide_ack_intr_t *) ide_interrupt_ack;
+	/* Enable Harddisk Interrupt,
+	 * and make it edge sensitive
+	 */
+	/* (11-18) Set edge detect for irq, no wakeup from low power mode */
+	((immap_t *) IMAP_ADDR)->im_siu_conf.sc_siel |=
+			(0x80000000 >> ioport_dsc[data_port].irq);
+}	/* m8xx_ide_init_hwif_ports() for CONFIG_IDE_8xx_DIRECT */ 
+
+#endif	/* CONFIG_IDE_8xx_DIRECT */
+
+
+/* -------------------------------------------------------------------- */
+
+
+/* PCMCIA Timing */
+#ifndef	PCMCIA_SHT
+#define PCMCIA_SHT(t)	((t & 0x0F)<<16)	/* Strobe Hold  Time 	*/
+#define PCMCIA_SST(t)	((t & 0x0F)<<12)	/* Strobe Setup Time	*/
+#define PCMCIA_SL(t) ((t==32) ? 0 : ((t & 0x1F)<<7)) /* Strobe Length	*/
+#endif
+
+
+/* Calculate PIO timings */
+static void
+m8xx_ide_tuneproc(ide_drive_t *drive, byte pio)
+{
+	ide_pio_data_t d;
+#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_IDE_8xx_DIRECT)
+	volatile pcmconf8xx_t	*pcmp;
+	ulong timing, mask, reg;
+#endif
+
+	pio = ide_get_best_pio_mode(drive, pio, 4, &d);
+
+#if 1
+	printk("%s[%d] %s: best PIO mode: %d\n",
+		__FILE__,__LINE__,__FUNCTION__, pio);
+#endif
+
+#if defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_IDE_8xx_DIRECT)
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)IMAP_ADDR)->im_pcmcia));
+
+	mask = ~(PCMCIA_SHT(0xFF) | PCMCIA_SST(0xFF) | PCMCIA_SL(0xFF));
+
+	timing  = PCMCIA_SHT(hold_time[pio]  )
+		| PCMCIA_SST(ide_pio_clocks[pio].setup_time )
+		| PCMCIA_SL (ide_pio_clocks[pio].active_time)
+		;
+
+#if 1
+	printk ("Setting timing bits 0x%08lx in PCMCIA controller\n", timing);
+#endif
+	if ((reg = pcmp->pcmc_por0 & mask) != 0)
+		pcmp->pcmc_por0 = reg | timing;
+
+	if ((reg = pcmp->pcmc_por1 & mask) != 0)
+		pcmp->pcmc_por1 = reg | timing;
+
+	if ((reg = pcmp->pcmc_por2 & mask) != 0)
+		pcmp->pcmc_por2 = reg | timing;
+
+	if ((reg = pcmp->pcmc_por3 & mask) != 0)
+		pcmp->pcmc_por3 = reg | timing;
+
+	if ((reg = pcmp->pcmc_por4 & mask) != 0)
+		pcmp->pcmc_por4 = reg | timing;
+
+	if ((reg = pcmp->pcmc_por5 & mask) != 0)
+		pcmp->pcmc_por5 = reg | timing;
+
+	if ((reg = pcmp->pcmc_por6 & mask) != 0)
+		pcmp->pcmc_por6 = reg | timing;
+
+	if ((reg = pcmp->pcmc_por7 & mask) != 0)
+		pcmp->pcmc_por7 = reg | timing;
+
+#elif defined(CONFIG_IDE_EXT_DIRECT)
+
+	printk("%s[%d] %s: not implemented yet!\n",
+		__FILE__,__LINE__,__FUNCTION__);
+#endif /* defined(CONFIG_IDE_8xx_PCCARD) || defined(CONFIG_IDE_8xx_PCMCIA */
+}
+
+static void
+ide_interrupt_ack (void *dev)
+{
+#ifdef CONFIG_IDE_8xx_PCCARD
+	u_int pscr, pipr;
+
+#if (PCMCIA_SOCKETS_NO == 2)
+	u_int _slot_;
+#endif
+
+	/* get interrupt sources */
+
+	pscr = ((volatile immap_t *)IMAP_ADDR)->im_pcmcia.pcmc_pscr;
+	pipr = ((volatile immap_t *)IMAP_ADDR)->im_pcmcia.pcmc_pipr;
+
+	/*
+	 * report only if both card detect signals are the same
+	 * not too nice done,
+	 * we depend on that CD2 is the bit to the left of CD1...
+	 */
+
+	if(_slot_==-1){
+	  printk("PCMCIA slot has not been defined! Using A as default\n");
+	  _slot_=0;
+	}
+
+	if(((pipr & M8XX_PCMCIA_CD2(_slot_)) >> 1) ^
+	   (pipr & M8XX_PCMCIA_CD1(_slot_))         ) {
+	  printk ("card detect interrupt\n");
+	}
+	/* clear the interrupt sources */
+	((immap_t *)IMAP_ADDR)->im_pcmcia.pcmc_pscr = pscr;
+
+#else /* ! CONFIG_IDE_8xx_PCCARD */
+	/*
+	 * Only CONFIG_IDE_8xx_PCCARD is using the interrupt of the
+	 * MPC8xx's PCMCIA controller, so there is nothing to be done here
+	 * for CONFIG_IDE_8xx_DIRECT and CONFIG_IDE_EXT_DIRECT.
+	 * The interrupt is handled somewhere else.	-- Steven
+	 */
+#endif /* CONFIG_IDE_8xx_PCCARD */
+}
+
+
+
+/*
+ * CIS Tupel codes
+ */
+#define CISTPL_NULL		0x00
+#define CISTPL_DEVICE		0x01
+#define CISTPL_LONGLINK_CB	0x02
+#define CISTPL_INDIRECT		0x03
+#define CISTPL_CONFIG_CB	0x04
+#define CISTPL_CFTABLE_ENTRY_CB 0x05
+#define CISTPL_LONGLINK_MFC	0x06
+#define CISTPL_BAR		0x07
+#define CISTPL_PWR_MGMNT	0x08
+#define CISTPL_EXTDEVICE	0x09
+#define CISTPL_CHECKSUM		0x10
+#define CISTPL_LONGLINK_A	0x11
+#define CISTPL_LONGLINK_C	0x12
+#define CISTPL_LINKTARGET	0x13
+#define CISTPL_NO_LINK		0x14
+#define CISTPL_VERS_1		0x15
+#define CISTPL_ALTSTR		0x16
+#define CISTPL_DEVICE_A		0x17
+#define CISTPL_JEDEC_C		0x18
+#define CISTPL_JEDEC_A		0x19
+#define CISTPL_CONFIG		0x1a
+#define CISTPL_CFTABLE_ENTRY	0x1b
+#define CISTPL_DEVICE_OC	0x1c
+#define CISTPL_DEVICE_OA	0x1d
+#define CISTPL_DEVICE_GEO	0x1e
+#define CISTPL_DEVICE_GEO_A	0x1f
+#define CISTPL_MANFID		0x20
+#define CISTPL_FUNCID		0x21
+#define CISTPL_FUNCE		0x22
+#define CISTPL_SWIL		0x23
+#define CISTPL_END		0xff
+
+/*
+ * CIS Function ID codes
+ */
+#define CISTPL_FUNCID_MULTI	0x00
+#define CISTPL_FUNCID_MEMORY	0x01
+#define CISTPL_FUNCID_SERIAL	0x02
+#define CISTPL_FUNCID_PARALLEL	0x03
+#define CISTPL_FUNCID_FIXED	0x04
+#define CISTPL_FUNCID_VIDEO	0x05
+#define CISTPL_FUNCID_NETWORK	0x06
+#define CISTPL_FUNCID_AIMS	0x07
+#define CISTPL_FUNCID_SCSI	0x08
+
+/*
+ * Fixed Disk FUNCE codes
+ */
+#define CISTPL_IDE_INTERFACE	0x01
+
+#define CISTPL_FUNCE_IDE_IFACE	0x01
+#define CISTPL_FUNCE_IDE_MASTER	0x02
+#define CISTPL_FUNCE_IDE_SLAVE	0x03
+
+/* First feature byte */
+#define CISTPL_IDE_SILICON	0x04
+#define CISTPL_IDE_UNIQUE	0x08
+#define CISTPL_IDE_DUAL		0x10
+
+/* Second feature byte */
+#define CISTPL_IDE_HAS_SLEEP	0x01
+#define CISTPL_IDE_HAS_STANDBY	0x02
+#define CISTPL_IDE_HAS_IDLE	0x04
+#define CISTPL_IDE_LOW_POWER	0x08
+#define CISTPL_IDE_REG_INHIBIT	0x10
+#define CISTPL_IDE_HAS_INDEX	0x20
+#define CISTPL_IDE_IOIS16	0x40
+
+
+/* -------------------------------------------------------------------- */
+
+
+#define	MAX_TUPEL_SZ	512
+#define MAX_FEATURES	4
+
+static int check_ide_device (unsigned long base)
+{
+	volatile unsigned char *ident = NULL;
+	volatile unsigned char *feature_p[MAX_FEATURES];
+	volatile unsigned char *p, *start;
+	int n_features = 0;
+	unsigned char func_id = ~0;
+	unsigned char code, len;
+	unsigned short config_base = 0;
+	int found = 0;
+	int i;
+
+#ifdef DEBUG
+	printk ("PCMCIA MEM: %08lX\n", base);
+#endif
+	start = p = (volatile unsigned char *) base;
+
+	while ((p - start) < MAX_TUPEL_SZ) {
+
+		code = *p; p += 2;
+
+		if (code == 0xFF) { /* End of chain */
+			break;
+		}
+
+		len = *p; p += 2;
+#ifdef	DEBUG_PCMCIA
+		{ volatile unsigned char *q = p;
+			printk ("\nTuple code %02x  length %d\n\tData:",
+				code, len);
+
+			for (i = 0; i < len; ++i) {
+				printk (" %02x", *q);
+				q+= 2;
+			}
+		}
+#endif	/* DEBUG_PCMCIA */
+		switch (code) {
+		case CISTPL_VERS_1:
+			ident = p + 4;
+			break;
+		case CISTPL_FUNCID:
+			func_id = *p;
+			break;
+		case CISTPL_FUNCE:
+			if (n_features < MAX_FEATURES)
+				feature_p[n_features++] = p;
+			break;
+		case CISTPL_CONFIG:
+			config_base = (*(p+6) << 8) + (*(p+4));
+		default:
+			break;
+		}
+		p += 2 * len;
+	}
+
+	found = identify (ident);
+
+	if (func_id != ((unsigned char)~0)) {
+		print_funcid (func_id);
+
+		if (func_id == CISTPL_FUNCID_FIXED)
+			found = 1;
+		else
+			return (1);	/* no disk drive */
+	}
+
+	for (i=0; i<n_features; ++i) {
+		print_fixed (feature_p[i]);
+	}
+
+	if (!found) {
+		printk ("unknown card type\n");
+		return (1);
+	}
+
+	/* set level mode irq and I/O mapped device in config reg*/
+	*((unsigned char *)(base + config_base)) = 0x41;
+
+	return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+static void print_funcid (int func)
+{
+	switch (func) {
+	case CISTPL_FUNCID_MULTI:
+		printk (" Multi-Function");
+		break;
+	case CISTPL_FUNCID_MEMORY:
+		printk (" Memory");
+		break;
+	case CISTPL_FUNCID_SERIAL:
+		printk (" Serial Port");
+		break;
+	case CISTPL_FUNCID_PARALLEL:
+		printk (" Parallel Port");
+		break;
+	case CISTPL_FUNCID_FIXED:
+		printk (" Fixed Disk");
+		break;
+	case CISTPL_FUNCID_VIDEO:
+		printk (" Video Adapter");
+		break;
+	case CISTPL_FUNCID_NETWORK:
+		printk (" Network Adapter");
+		break;
+	case CISTPL_FUNCID_AIMS:
+		printk (" AIMS Card");
+		break;
+	case CISTPL_FUNCID_SCSI:
+		printk (" SCSI Adapter");
+		break;
+	default:
+		printk (" Unknown");
+		break;
+	}
+	printk (" Card\n");
+}
+
+/* ------------------------------------------------------------------------- */
+
+static void print_fixed (volatile unsigned char *p)
+{
+	if (p == NULL)
+		return;
+
+	switch (*p) {
+	case CISTPL_FUNCE_IDE_IFACE:
+	    {   unsigned char iface = *(p+2);
+
+		printk ((iface == CISTPL_IDE_INTERFACE) ? " IDE" : " unknown");
+		printk (" interface ");
+		break;
+	    }
+	case CISTPL_FUNCE_IDE_MASTER:
+	case CISTPL_FUNCE_IDE_SLAVE:
+	    {   unsigned char f1 = *(p+2);
+		unsigned char f2 = *(p+4);
+
+		printk ((f1 & CISTPL_IDE_SILICON) ? " [silicon]" : " [rotating]");
+
+		if (f1 & CISTPL_IDE_UNIQUE)
+			printk (" [unique]");
+
+		printk ((f1 & CISTPL_IDE_DUAL) ? " [dual]" : " [single]");
+
+		if (f2 & CISTPL_IDE_HAS_SLEEP)
+			printk (" [sleep]");
+
+		if (f2 & CISTPL_IDE_HAS_STANDBY)
+			printk (" [standby]");
+
+		if (f2 & CISTPL_IDE_HAS_IDLE)
+			printk (" [idle]");
+
+		if (f2 & CISTPL_IDE_LOW_POWER)
+			printk (" [low power]");
+
+		if (f2 & CISTPL_IDE_REG_INHIBIT)
+			printk (" [reg inhibit]");
+
+		if (f2 & CISTPL_IDE_HAS_INDEX)
+			printk (" [index]");
+
+		if (f2 & CISTPL_IDE_IOIS16)
+			printk (" [IOis16]");
+
+		break;
+	    }
+	}
+	printk ("\n");
+}
+
+/* ------------------------------------------------------------------------- */
+
+
+#define MAX_IDENT_CHARS		64
+#define	MAX_IDENT_FIELDS	4
+
+static unsigned char *known_cards[] = {
+	"ARGOSY PnPIDE D5",
+	NULL
+};
+
+static int identify  (volatile unsigned char *p)
+{
+	unsigned char id_str[MAX_IDENT_CHARS];
+	unsigned char data;
+	unsigned char *t;
+	unsigned char **card;
+	int i, done;
+
+	if (p == NULL)
+		return (0);	/* Don't know */
+
+	t = id_str;
+	done =0;
+
+	for (i=0; i<=4 && !done; ++i, p+=2) {
+		while ((data = *p) != '\0') {
+			if (data == 0xFF) {
+				done = 1;
+				break;
+			}
+			*t++ = data;
+			if (t == &id_str[MAX_IDENT_CHARS-1]) {
+				done = 1;
+				break;
+			}
+			p += 2;
+		}
+		if (!done)
+			*t++ = ' ';
+	}
+	*t = '\0';
+	while (--t > id_str) {
+		if (*t == ' ')
+			*t = '\0';
+		else
+			break;
+	}
+	printk ("Card ID: %s\n", id_str);
+
+	for (card=known_cards; *card; ++card) {
+		if (strcmp(*card, id_str) == 0) {	/* found! */
+			return (1);
+		}
+	}
+
+	return (0);	/* don't know */
+}
+
+void m8xx_ide_init(void)
+{
+	ppc_ide_md.default_irq          = m8xx_ide_default_irq;
+	ppc_ide_md.default_io_base      = m8xx_ide_default_io_base;
+	ppc_ide_md.ide_init_hwif        = m8xx_ide_init_hwif_ports;
+}
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)