patch-2.4.11-dontuse linux/arch/ppc/8xx_io/commproc.h
Next file: linux/arch/ppc/8xx_io/enet.c
Previous file: linux/arch/ppc/8xx_io/commproc.c
Back to the patch index
Back to the overall index
- Lines: 797
- Date:
Wed Dec 31 16:00:00 1969
- Orig file:
v2.4.10/linux/arch/ppc/8xx_io/commproc.h
- Orig date:
Tue Jul 3 17:08:18 2001
diff -u --recursive --new-file v2.4.10/linux/arch/ppc/8xx_io/commproc.h linux/arch/ppc/8xx_io/commproc.h
@@ -1,796 +0,0 @@
-/*
- * BK Id: SCCS/s.commproc.h 1.13 06/15/01 13:00:20 paulus
- */
-
-/*
- * MPC8xx Communication Processor Module.
- * Copyright (c) 1997 Dan Malek (dmalek@jlc.net)
- *
- * This file contains structures and information for the communication
- * processor channels. Some CPM control and status is available
- * throught the MPC8xx internal memory map. See immap.h for details.
- * This file only contains what I need for the moment, not the total
- * CPM capabilities. I (or someone else) will add definitions as they
- * are needed. -- Dan
- *
- * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
- * bytes of the DP RAM and relocates the I2C parameter area to the
- * IDMA1 space. The remaining DP RAM is available for buffer descriptors
- * or other use.
- */
-#ifndef __CPM_8XX__
-#define __CPM_8XX__
-
-#include <linux/config.h>
-#include <asm/8xx_immap.h>
-
-/* CPM Command register.
-*/
-#define CPM_CR_RST ((ushort)0x8000)
-#define CPM_CR_OPCODE ((ushort)0x0f00)
-#define CPM_CR_CHAN ((ushort)0x00f0)
-#define CPM_CR_FLG ((ushort)0x0001)
-
-/* Some commands (there are more...later)
-*/
-#define CPM_CR_INIT_TRX ((ushort)0x0000)
-#define CPM_CR_INIT_RX ((ushort)0x0001)
-#define CPM_CR_INIT_TX ((ushort)0x0002)
-#define CPM_CR_HUNT_MODE ((ushort)0x0003)
-#define CPM_CR_STOP_TX ((ushort)0x0004)
-#define CPM_CR_RESTART_TX ((ushort)0x0006)
-#define CPM_CR_SET_GADDR ((ushort)0x0008)
-
-/* Channel numbers.
-*/
-#define CPM_CR_CH_SCC1 ((ushort)0x0000)
-#define CPM_CR_CH_I2C ((ushort)0x0001) /* I2C and IDMA1 */
-#define CPM_CR_CH_SCC2 ((ushort)0x0004)
-#define CPM_CR_CH_SPI ((ushort)0x0005) /* SPI / IDMA2 / Timers */
-#define CPM_CR_CH_SCC3 ((ushort)0x0008)
-#define CPM_CR_CH_SMC1 ((ushort)0x0009) /* SMC1 / DSP1 */
-#define CPM_CR_CH_SCC4 ((ushort)0x000c)
-#define CPM_CR_CH_SMC2 ((ushort)0x000d) /* SMC2 / DSP2 */
-
-#define mk_cr_cmd(CH, CMD) ((CMD << 8) | (CH << 4))
-
-/* The dual ported RAM is multi-functional. Some areas can be (and are
- * being) used for microcode. There is an area that can only be used
- * as data ram for buffer descriptors, which is all we use right now.
- * Currently the first 512 and last 256 bytes are used for microcode.
- */
-#define CPM_DATAONLY_BASE ((uint)0x0800)
-#define CPM_DATAONLY_SIZE ((uint)0x0700)
-#define CPM_DP_NOSPACE ((uint)0x7fffffff)
-
-/* Export the base address of the communication processor registers
- * and dual port ram.
- */
-extern cpm8xx_t *cpmp; /* Pointer to comm processor */
-uint m8xx_cpm_dpalloc(uint size);
-uint m8xx_cpm_hostalloc(uint size);
-void m8xx_cpm_setbrg(uint brg, uint rate);
-
-/* Buffer descriptors used by many of the CPM protocols.
-*/
-typedef struct cpm_buf_desc {
- ushort cbd_sc; /* Status and Control */
- ushort cbd_datlen; /* Data length in buffer */
- uint cbd_bufaddr; /* Buffer address in host memory */
-} cbd_t;
-
-#define BD_SC_EMPTY ((ushort)0x8000) /* Receive is empty */
-#define BD_SC_READY ((ushort)0x8000) /* Transmit is ready */
-#define BD_SC_WRAP ((ushort)0x2000) /* Last buffer descriptor */
-#define BD_SC_INTRPT ((ushort)0x1000) /* Interrupt on change */
-#define BD_SC_LAST ((ushort)0x0800) /* Last buffer in frame */
-#define BD_SC_CM ((ushort)0x0200) /* Continous mode */
-#define BD_SC_ID ((ushort)0x0100) /* Rec'd too many idles */
-#define BD_SC_P ((ushort)0x0100) /* xmt preamble */
-#define BD_SC_BR ((ushort)0x0020) /* Break received */
-#define BD_SC_FR ((ushort)0x0010) /* Framing error */
-#define BD_SC_PR ((ushort)0x0008) /* Parity error */
-#define BD_SC_OV ((ushort)0x0002) /* Overrun */
-#define BD_SC_CD ((ushort)0x0001) /* ?? */
-
-/* Parameter RAM offsets.
-*/
-#define PROFF_SCC1 ((uint)0x0000)
-#define PROFF_IIC ((uint)0x0080)
-#define PROFF_SCC2 ((uint)0x0100)
-#define PROFF_SCC3 ((uint)0x0200)
-#define PROFF_SMC1 ((uint)0x0280)
-#define PROFF_SCC4 ((uint)0x0300)
-#define PROFF_SMC2 ((uint)0x0380)
-
-/* Define enough so I can at least use the serial port as a UART.
- * The MBX uses SMC1 as the host serial port.
- */
-typedef struct smc_uart {
- ushort smc_rbase; /* Rx Buffer descriptor base address */
- ushort smc_tbase; /* Tx Buffer descriptor base address */
- u_char smc_rfcr; /* Rx function code */
- u_char smc_tfcr; /* Tx function code */
- ushort smc_mrblr; /* Max receive buffer length */
- uint smc_rstate; /* Internal */
- uint smc_idp; /* Internal */
- ushort smc_rbptr; /* Internal */
- ushort smc_ibc; /* Internal */
- uint smc_rxtmp; /* Internal */
- uint smc_tstate; /* Internal */
- uint smc_tdp; /* Internal */
- ushort smc_tbptr; /* Internal */
- ushort smc_tbc; /* Internal */
- uint smc_txtmp; /* Internal */
- ushort smc_maxidl; /* Maximum idle characters */
- ushort smc_tmpidl; /* Temporary idle counter */
- ushort smc_brklen; /* Last received break length */
- ushort smc_brkec; /* rcv'd break condition counter */
- ushort smc_brkcr; /* xmt break count register */
- ushort smc_rmask; /* Temporary bit mask */
-} smc_uart_t;
-
-/* Function code bits.
-*/
-#define SMC_EB ((u_char)0x10) /* Set big endian byte order */
-
-/* SMC uart mode register.
-*/
-#define SMCMR_REN ((ushort)0x0001)
-#define SMCMR_TEN ((ushort)0x0002)
-#define SMCMR_DM ((ushort)0x000c)
-#define SMCMR_SM_GCI ((ushort)0x0000)
-#define SMCMR_SM_UART ((ushort)0x0020)
-#define SMCMR_SM_TRANS ((ushort)0x0030)
-#define SMCMR_SM_MASK ((ushort)0x0030)
-#define SMCMR_PM_EVEN ((ushort)0x0100) /* Even parity, else odd */
-#define SMCMR_REVD SMCMR_PM_EVEN
-#define SMCMR_PEN ((ushort)0x0200) /* Parity enable */
-#define SMCMR_BS SMCMR_PEN
-#define SMCMR_SL ((ushort)0x0400) /* Two stops, else one */
-#define SMCR_CLEN_MASK ((ushort)0x7800) /* Character length */
-#define smcr_mk_clen(C) (((C) << 11) & SMCR_CLEN_MASK)
-
-/* SMC2 as Centronics parallel printer. It is half duplex, in that
- * it can only receive or transmit. The parameter ram values for
- * each direction are either unique or properly overlap, so we can
- * include them in one structure.
- */
-typedef struct smc_centronics {
- ushort scent_rbase;
- ushort scent_tbase;
- u_char scent_cfcr;
- u_char scent_smask;
- ushort scent_mrblr;
- uint scent_rstate;
- uint scent_r_ptr;
- ushort scent_rbptr;
- ushort scent_r_cnt;
- uint scent_rtemp;
- uint scent_tstate;
- uint scent_t_ptr;
- ushort scent_tbptr;
- ushort scent_t_cnt;
- uint scent_ttemp;
- ushort scent_max_sl;
- ushort scent_sl_cnt;
- ushort scent_character1;
- ushort scent_character2;
- ushort scent_character3;
- ushort scent_character4;
- ushort scent_character5;
- ushort scent_character6;
- ushort scent_character7;
- ushort scent_character8;
- ushort scent_rccm;
- ushort scent_rccr;
-} smc_cent_t;
-
-/* Centronics Status Mask Register.
-*/
-#define SMC_CENT_F ((u_char)0x08)
-#define SMC_CENT_PE ((u_char)0x04)
-#define SMC_CENT_S ((u_char)0x02)
-
-/* SMC Event and Mask register.
-*/
-#define SMCM_BRKE ((unsigned char)0x40) /* When in UART Mode */
-#define SMCM_BRK ((unsigned char)0x10) /* When in UART Mode */
-#define SMCM_TXE ((unsigned char)0x10) /* When in Transparent Mode */
-#define SMCM_BSY ((unsigned char)0x04)
-#define SMCM_TX ((unsigned char)0x02)
-#define SMCM_RX ((unsigned char)0x01)
-
-/* Baud rate generators.
-*/
-#define CPM_BRG_RST ((uint)0x00020000)
-#define CPM_BRG_EN ((uint)0x00010000)
-#define CPM_BRG_EXTC_INT ((uint)0x00000000)
-#define CPM_BRG_EXTC_CLK2 ((uint)0x00004000)
-#define CPM_BRG_EXTC_CLK6 ((uint)0x00008000)
-#define CPM_BRG_ATB ((uint)0x00002000)
-#define CPM_BRG_CD_MASK ((uint)0x00001ffe)
-#define CPM_BRG_DIV16 ((uint)0x00000001)
-
-/* SCCs.
-*/
-#define SCC_GSMRH_IRP ((uint)0x00040000)
-#define SCC_GSMRH_GDE ((uint)0x00010000)
-#define SCC_GSMRH_TCRC_CCITT ((uint)0x00008000)
-#define SCC_GSMRH_TCRC_BISYNC ((uint)0x00004000)
-#define SCC_GSMRH_TCRC_HDLC ((uint)0x00000000)
-#define SCC_GSMRH_REVD ((uint)0x00002000)
-#define SCC_GSMRH_TRX ((uint)0x00001000)
-#define SCC_GSMRH_TTX ((uint)0x00000800)
-#define SCC_GSMRH_CDP ((uint)0x00000400)
-#define SCC_GSMRH_CTSP ((uint)0x00000200)
-#define SCC_GSMRH_CDS ((uint)0x00000100)
-#define SCC_GSMRH_CTSS ((uint)0x00000080)
-#define SCC_GSMRH_TFL ((uint)0x00000040)
-#define SCC_GSMRH_RFW ((uint)0x00000020)
-#define SCC_GSMRH_TXSY ((uint)0x00000010)
-#define SCC_GSMRH_SYNL16 ((uint)0x0000000c)
-#define SCC_GSMRH_SYNL8 ((uint)0x00000008)
-#define SCC_GSMRH_SYNL4 ((uint)0x00000004)
-#define SCC_GSMRH_RTSM ((uint)0x00000002)
-#define SCC_GSMRH_RSYN ((uint)0x00000001)
-
-#define SCC_GSMRL_SIR ((uint)0x80000000) /* SCC2 only */
-#define SCC_GSMRL_EDGE_NONE ((uint)0x60000000)
-#define SCC_GSMRL_EDGE_NEG ((uint)0x40000000)
-#define SCC_GSMRL_EDGE_POS ((uint)0x20000000)
-#define SCC_GSMRL_EDGE_BOTH ((uint)0x00000000)
-#define SCC_GSMRL_TCI ((uint)0x10000000)
-#define SCC_GSMRL_TSNC_3 ((uint)0x0c000000)
-#define SCC_GSMRL_TSNC_4 ((uint)0x08000000)
-#define SCC_GSMRL_TSNC_14 ((uint)0x04000000)
-#define SCC_GSMRL_TSNC_INF ((uint)0x00000000)
-#define SCC_GSMRL_RINV ((uint)0x02000000)
-#define SCC_GSMRL_TINV ((uint)0x01000000)
-#define SCC_GSMRL_TPL_128 ((uint)0x00c00000)
-#define SCC_GSMRL_TPL_64 ((uint)0x00a00000)
-#define SCC_GSMRL_TPL_48 ((uint)0x00800000)
-#define SCC_GSMRL_TPL_32 ((uint)0x00600000)
-#define SCC_GSMRL_TPL_16 ((uint)0x00400000)
-#define SCC_GSMRL_TPL_8 ((uint)0x00200000)
-#define SCC_GSMRL_TPL_NONE ((uint)0x00000000)
-#define SCC_GSMRL_TPP_ALL1 ((uint)0x00180000)
-#define SCC_GSMRL_TPP_01 ((uint)0x00100000)
-#define SCC_GSMRL_TPP_10 ((uint)0x00080000)
-#define SCC_GSMRL_TPP_ZEROS ((uint)0x00000000)
-#define SCC_GSMRL_TEND ((uint)0x00040000)
-#define SCC_GSMRL_TDCR_32 ((uint)0x00030000)
-#define SCC_GSMRL_TDCR_16 ((uint)0x00020000)
-#define SCC_GSMRL_TDCR_8 ((uint)0x00010000)
-#define SCC_GSMRL_TDCR_1 ((uint)0x00000000)
-#define SCC_GSMRL_RDCR_32 ((uint)0x0000c000)
-#define SCC_GSMRL_RDCR_16 ((uint)0x00008000)
-#define SCC_GSMRL_RDCR_8 ((uint)0x00004000)
-#define SCC_GSMRL_RDCR_1 ((uint)0x00000000)
-#define SCC_GSMRL_RENC_DFMAN ((uint)0x00003000)
-#define SCC_GSMRL_RENC_MANCH ((uint)0x00002000)
-#define SCC_GSMRL_RENC_FM0 ((uint)0x00001000)
-#define SCC_GSMRL_RENC_NRZI ((uint)0x00000800)
-#define SCC_GSMRL_RENC_NRZ ((uint)0x00000000)
-#define SCC_GSMRL_TENC_DFMAN ((uint)0x00000600)
-#define SCC_GSMRL_TENC_MANCH ((uint)0x00000400)
-#define SCC_GSMRL_TENC_FM0 ((uint)0x00000200)
-#define SCC_GSMRL_TENC_NRZI ((uint)0x00000100)
-#define SCC_GSMRL_TENC_NRZ ((uint)0x00000000)
-#define SCC_GSMRL_DIAG_LE ((uint)0x000000c0) /* Loop and echo */
-#define SCC_GSMRL_DIAG_ECHO ((uint)0x00000080)
-#define SCC_GSMRL_DIAG_LOOP ((uint)0x00000040)
-#define SCC_GSMRL_DIAG_NORM ((uint)0x00000000)
-#define SCC_GSMRL_ENR ((uint)0x00000020)
-#define SCC_GSMRL_ENT ((uint)0x00000010)
-#define SCC_GSMRL_MODE_ENET ((uint)0x0000000c)
-#define SCC_GSMRL_MODE_DDCMP ((uint)0x00000009)
-#define SCC_GSMRL_MODE_BISYNC ((uint)0x00000008)
-#define SCC_GSMRL_MODE_V14 ((uint)0x00000007)
-#define SCC_GSMRL_MODE_AHDLC ((uint)0x00000006)
-#define SCC_GSMRL_MODE_PROFIBUS ((uint)0x00000005)
-#define SCC_GSMRL_MODE_UART ((uint)0x00000004)
-#define SCC_GSMRL_MODE_SS7 ((uint)0x00000003)
-#define SCC_GSMRL_MODE_ATALK ((uint)0x00000002)
-#define SCC_GSMRL_MODE_HDLC ((uint)0x00000000)
-
-#define SCC_TODR_TOD ((ushort)0x8000)
-
-/* SCC Event and Mask register.
-*/
-#define SCCM_TXE ((unsigned char)0x10)
-#define SCCM_BSY ((unsigned char)0x04)
-#define SCCM_TX ((unsigned char)0x02)
-#define SCCM_RX ((unsigned char)0x01)
-
-typedef struct scc_param {
- ushort scc_rbase; /* Rx Buffer descriptor base address */
- ushort scc_tbase; /* Tx Buffer descriptor base address */
- u_char scc_rfcr; /* Rx function code */
- u_char scc_tfcr; /* Tx function code */
- ushort scc_mrblr; /* Max receive buffer length */
- uint scc_rstate; /* Internal */
- uint scc_idp; /* Internal */
- ushort scc_rbptr; /* Internal */
- ushort scc_ibc; /* Internal */
- uint scc_rxtmp; /* Internal */
- uint scc_tstate; /* Internal */
- uint scc_tdp; /* Internal */
- ushort scc_tbptr; /* Internal */
- ushort scc_tbc; /* Internal */
- uint scc_txtmp; /* Internal */
- uint scc_rcrc; /* Internal */
- uint scc_tcrc; /* Internal */
-} sccp_t;
-
-/* Function code bits.
-*/
-#define SCC_EB ((u_char)0x10) /* Set big endian byte order */
-
-/* CPM Ethernet through SCCx.
- */
-typedef struct scc_enet {
- sccp_t sen_genscc;
- uint sen_cpres; /* Preset CRC */
- uint sen_cmask; /* Constant mask for CRC */
- uint sen_crcec; /* CRC Error counter */
- uint sen_alec; /* alignment error counter */
- uint sen_disfc; /* discard frame counter */
- ushort sen_pads; /* Tx short frame pad character */
- ushort sen_retlim; /* Retry limit threshold */
- ushort sen_retcnt; /* Retry limit counter */
- ushort sen_maxflr; /* maximum frame length register */
- ushort sen_minflr; /* minimum frame length register */
- ushort sen_maxd1; /* maximum DMA1 length */
- ushort sen_maxd2; /* maximum DMA2 length */
- ushort sen_maxd; /* Rx max DMA */
- ushort sen_dmacnt; /* Rx DMA counter */
- ushort sen_maxb; /* Max BD byte count */
- ushort sen_gaddr1; /* Group address filter */
- ushort sen_gaddr2;
- ushort sen_gaddr3;
- ushort sen_gaddr4;
- uint sen_tbuf0data0; /* Save area 0 - current frame */
- uint sen_tbuf0data1; /* Save area 1 - current frame */
- uint sen_tbuf0rba; /* Internal */
- uint sen_tbuf0crc; /* Internal */
- ushort sen_tbuf0bcnt; /* Internal */
- ushort sen_paddrh; /* physical address (MSB) */
- ushort sen_paddrm;
- ushort sen_paddrl; /* physical address (LSB) */
- ushort sen_pper; /* persistence */
- ushort sen_rfbdptr; /* Rx first BD pointer */
- ushort sen_tfbdptr; /* Tx first BD pointer */
- ushort sen_tlbdptr; /* Tx last BD pointer */
- uint sen_tbuf1data0; /* Save area 0 - current frame */
- uint sen_tbuf1data1; /* Save area 1 - current frame */
- uint sen_tbuf1rba; /* Internal */
- uint sen_tbuf1crc; /* Internal */
- ushort sen_tbuf1bcnt; /* Internal */
- ushort sen_txlen; /* Tx Frame length counter */
- ushort sen_iaddr1; /* Individual address filter */
- ushort sen_iaddr2;
- ushort sen_iaddr3;
- ushort sen_iaddr4;
- ushort sen_boffcnt; /* Backoff counter */
-
- /* NOTE: Some versions of the manual have the following items
- * incorrectly documented. Below is the proper order.
- */
- ushort sen_taddrh; /* temp address (MSB) */
- ushort sen_taddrm;
- ushort sen_taddrl; /* temp address (LSB) */
-} scc_enet_t;
-
-/*** MBX ************************************************************/
-
-#ifdef CONFIG_MBX
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use. The TCLK and RCLK seem unique
- * to the MBX860 board. Any two of the four available clocks could be
- * used, and the MPC860 cookbook manual has an example using different
- * clock pins.
- */
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PC_ENET_TENA ((ushort)0x0001)
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000003d)
-#endif /* CONFIG_MBX */
-
-/*** RPXLITE ********************************************************/
-
-#ifdef CONFIG_RPXLITE
-/* This ENET stuff is for the MPC850 with ethernet on SCC2. Some of
- * this may be unique to the RPX-Lite configuration.
- * Note TENA is on Port B.
- */
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00003d00)
-#endif /* CONFIG_RPXLITE */
-
-/*** BSEIP **********************************************************/
-
-#ifdef CONFIG_BSEIP
-/* This ENET stuff is for the MPC823 with ethernet on SCC2.
- * This is unique to the BSE ip-Engine board.
- */
-#define PA_ENET_RXD ((ushort)0x0004)
-#define PA_ENET_TXD ((ushort)0x0008)
-#define PA_ENET_TCLK ((ushort)0x0100)
-#define PA_ENET_RCLK ((ushort)0x0200)
-#define PB_ENET_TENA ((uint)0x00002000)
-#define PC_ENET_CLSN ((ushort)0x0040)
-#define PC_ENET_RENA ((ushort)0x0080)
-
-/* BSE uses port B and C bits for PHY control also.
-*/
-#define PB_BSE_POWERUP ((uint)0x00000004)
-#define PB_BSE_FDXDIS ((uint)0x00008000)
-#define PC_BSE_LOOPBACK ((ushort)0x0800)
-
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002c00)
-#endif /* CONFIG_BSEIP */
-
-/*** RPXCLASSIC *****************************************************/
-
-#ifdef CONFIG_RPXCLASSIC
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PB_ENET_TENA ((uint)0x00001000)
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000003d)
-#endif /* CONFIG_RPXCLASSIC */
-
-/*** TQM823L, TQM850L ***********************************************/
-
-#if defined(CONFIG_TQM823L) || defined(CONFIG_TQM850L)
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002600)
-#endif /* CONFIG_TQM823L, CONFIG_TQM850L */
-
-/*** FPS850L *********************************************************/
-
-#ifdef CONFIG_FPS850L
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_TENA ((ushort)0x0002) /* PC 14 */
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002600)
-#endif /* CONFIG_FPS850L */
-
-/*** TQM860L ********************************************************/
-
-#ifdef CONFIG_TQM860L
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use.
- */
-#define PA_ENET_RXD ((ushort)0x0001) /* PA 15 */
-#define PA_ENET_TXD ((ushort)0x0002) /* PA 14 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_TENA ((ushort)0x0001) /* PC 15 */
-#define PC_ENET_CLSN ((ushort)0x0010) /* PC 11 */
-#define PC_ENET_RENA ((ushort)0x0020) /* PC 10 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x00000026)
-#endif /* CONFIG_TQM860L */
-
-/*** SPD823TS *******************************************************/
-
-#ifdef CONFIG_SPD823TS
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC2 use.
- */
-#define PA_ENET_MDC ((ushort)0x0001) /* PA 15 !!! */
-#define PA_ENET_MDIO ((ushort)0x0002) /* PA 14 !!! */
-#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */
-#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */
-#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */
-
-#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */
-#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */
-#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 !!! */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK2) to
- * SCC2. Also, make sure GR2 (bit 16) and SC2 (bit 17) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x0000ff00)
-#define SICR_ENET_CLKRT ((uint)0x00002E00)
-#endif /* CONFIG_SPD823TS */
-
-
-/*** SM850 *********************************************************/
-
-/* The SM850 Service Module uses SCC2 for IrDA and SCC3 for Ethernet */
-
-#ifdef CONFIG_SM850
-#define PB_ENET_RXD ((uint)0x00000004) /* PB 29 */
-#define PB_ENET_TXD ((uint)0x00000002) /* PB 30 */
-#define PA_ENET_RCLK ((ushort)0x0100) /* PA 7 */
-#define PA_ENET_TCLK ((ushort)0x0400) /* PA 5 */
-
-#define PC_ENET_LBK ((ushort)0x0008) /* PC 12 */
-#define PC_ENET_TENA ((ushort)0x0004) /* PC 13 */
-
-#define PC_ENET_RENA ((ushort)0x0800) /* PC 4 */
-#define PC_ENET_CLSN ((ushort)0x0400) /* PC 5 */
-
-/* Control bits in the SICR to route TCLK (CLK3) and RCLK (CLK1) to
- * SCC3. Also, make sure GR3 (bit 8) and SC3 (bit 9) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x00FF0000)
-#define SICR_ENET_CLKRT ((uint)0x00260000)
-#endif /* CONFIG_SM850 */
-
-/*********************************************************************/
-
-/* SCC Event register as used by Ethernet.
-*/
-#define SCCE_ENET_GRA ((ushort)0x0080) /* Graceful stop complete */
-#define SCCE_ENET_TXE ((ushort)0x0010) /* Transmit Error */
-#define SCCE_ENET_RXF ((ushort)0x0008) /* Full frame received */
-#define SCCE_ENET_BSY ((ushort)0x0004) /* All incoming buffers full */
-#define SCCE_ENET_TXB ((ushort)0x0002) /* A buffer was transmitted */
-#define SCCE_ENET_RXB ((ushort)0x0001) /* A buffer was received */
-
-/* SCC Mode Register (PMSR) as used by Ethernet.
-*/
-#define SCC_PMSR_HBC ((ushort)0x8000) /* Enable heartbeat */
-#define SCC_PMSR_FC ((ushort)0x4000) /* Force collision */
-#define SCC_PMSR_RSH ((ushort)0x2000) /* Receive short frames */
-#define SCC_PMSR_IAM ((ushort)0x1000) /* Check individual hash */
-#define SCC_PMSR_ENCRC ((ushort)0x0800) /* Ethernet CRC mode */
-#define SCC_PMSR_PRO ((ushort)0x0200) /* Promiscuous mode */
-#define SCC_PMSR_BRO ((ushort)0x0100) /* Catch broadcast pkts */
-#define SCC_PMSR_SBT ((ushort)0x0080) /* Special backoff timer */
-#define SCC_PMSR_LPB ((ushort)0x0040) /* Set Loopback mode */
-#define SCC_PMSR_SIP ((ushort)0x0020) /* Sample Input Pins */
-#define SCC_PMSR_LCW ((ushort)0x0010) /* Late collision window */
-#define SCC_PMSR_NIB22 ((ushort)0x000a) /* Start frame search */
-#define SCC_PMSR_FDE ((ushort)0x0001) /* Full duplex enable */
-
-/* Buffer descriptor control/status used by Ethernet receive.
-*/
-#define BD_ENET_RX_EMPTY ((ushort)0x8000)
-#define BD_ENET_RX_WRAP ((ushort)0x2000)
-#define BD_ENET_RX_INTR ((ushort)0x1000)
-#define BD_ENET_RX_LAST ((ushort)0x0800)
-#define BD_ENET_RX_FIRST ((ushort)0x0400)
-#define BD_ENET_RX_MISS ((ushort)0x0100)
-#define BD_ENET_RX_LG ((ushort)0x0020)
-#define BD_ENET_RX_NO ((ushort)0x0010)
-#define BD_ENET_RX_SH ((ushort)0x0008)
-#define BD_ENET_RX_CR ((ushort)0x0004)
-#define BD_ENET_RX_OV ((ushort)0x0002)
-#define BD_ENET_RX_CL ((ushort)0x0001)
-#define BD_ENET_RX_STATS ((ushort)0x013f) /* All status bits */
-
-/* Buffer descriptor control/status used by Ethernet transmit.
-*/
-#define BD_ENET_TX_READY ((ushort)0x8000)
-#define BD_ENET_TX_PAD ((ushort)0x4000)
-#define BD_ENET_TX_WRAP ((ushort)0x2000)
-#define BD_ENET_TX_INTR ((ushort)0x1000)
-#define BD_ENET_TX_LAST ((ushort)0x0800)
-#define BD_ENET_TX_TC ((ushort)0x0400)
-#define BD_ENET_TX_DEF ((ushort)0x0200)
-#define BD_ENET_TX_HB ((ushort)0x0100)
-#define BD_ENET_TX_LC ((ushort)0x0080)
-#define BD_ENET_TX_RL ((ushort)0x0040)
-#define BD_ENET_TX_RCMASK ((ushort)0x003c)
-#define BD_ENET_TX_UN ((ushort)0x0002)
-#define BD_ENET_TX_CSL ((ushort)0x0001)
-#define BD_ENET_TX_STATS ((ushort)0x03ff) /* All status bits */
-
-/* SCC as UART
-*/
-typedef struct scc_uart {
- sccp_t scc_genscc;
- uint scc_res1; /* Reserved */
- uint scc_res2; /* Reserved */
- ushort scc_maxidl; /* Maximum idle chars */
- ushort scc_idlc; /* temp idle counter */
- ushort scc_brkcr; /* Break count register */
- ushort scc_parec; /* receive parity error counter */
- ushort scc_frmec; /* receive framing error counter */
- ushort scc_nosec; /* receive noise counter */
- ushort scc_brkec; /* receive break condition counter */
- ushort scc_brkln; /* last received break length */
- ushort scc_uaddr1; /* UART address character 1 */
- ushort scc_uaddr2; /* UART address character 2 */
- ushort scc_rtemp; /* Temp storage */
- ushort scc_toseq; /* Transmit out of sequence char */
- ushort scc_char1; /* control character 1 */
- ushort scc_char2; /* control character 2 */
- ushort scc_char3; /* control character 3 */
- ushort scc_char4; /* control character 4 */
- ushort scc_char5; /* control character 5 */
- ushort scc_char6; /* control character 6 */
- ushort scc_char7; /* control character 7 */
- ushort scc_char8; /* control character 8 */
- ushort scc_rccm; /* receive control character mask */
- ushort scc_rccr; /* receive control character register */
- ushort scc_rlbc; /* receive last break character */
-} scc_uart_t;
-
-/* SCC Event and Mask registers when it is used as a UART.
-*/
-#define UART_SCCM_GLR ((ushort)0x1000)
-#define UART_SCCM_GLT ((ushort)0x0800)
-#define UART_SCCM_AB ((ushort)0x0200)
-#define UART_SCCM_IDL ((ushort)0x0100)
-#define UART_SCCM_GRA ((ushort)0x0080)
-#define UART_SCCM_BRKE ((ushort)0x0040)
-#define UART_SCCM_BRKS ((ushort)0x0020)
-#define UART_SCCM_CCR ((ushort)0x0008)
-#define UART_SCCM_BSY ((ushort)0x0004)
-#define UART_SCCM_TX ((ushort)0x0002)
-#define UART_SCCM_RX ((ushort)0x0001)
-
-/* The SCC PMSR when used as a UART.
-*/
-#define SCU_PMSR_FLC ((ushort)0x8000)
-#define SCU_PMSR_SL ((ushort)0x4000)
-#define SCU_PMSR_CL ((ushort)0x3000)
-#define SCU_PMSR_UM ((ushort)0x0c00)
-#define SCU_PMSR_FRZ ((ushort)0x0200)
-#define SCU_PMSR_RZS ((ushort)0x0100)
-#define SCU_PMSR_SYN ((ushort)0x0080)
-#define SCU_PMSR_DRT ((ushort)0x0040)
-#define SCU_PMSR_PEN ((ushort)0x0010)
-#define SCU_PMSR_RPM ((ushort)0x000c)
-#define SCU_PMSR_REVP ((ushort)0x0008)
-#define SCU_PMSR_TPM ((ushort)0x0003)
-#define SCU_PMSR_TEVP ((ushort)0x0003)
-
-/* CPM Transparent mode SCC.
- */
-typedef struct scc_trans {
- sccp_t st_genscc;
- uint st_cpres; /* Preset CRC */
- uint st_cmask; /* Constant mask for CRC */
-} scc_trans_t;
-
-#define BD_SCC_TX_LAST ((ushort)0x0800)
-
-/* IIC parameter RAM.
-*/
-typedef struct iic {
- ushort iic_rbase; /* Rx Buffer descriptor base address */
- ushort iic_tbase; /* Tx Buffer descriptor base address */
- u_char iic_rfcr; /* Rx function code */
- u_char iic_tfcr; /* Tx function code */
- ushort iic_mrblr; /* Max receive buffer length */
- uint iic_rstate; /* Internal */
- uint iic_rdp; /* Internal */
- ushort iic_rbptr; /* Internal */
- ushort iic_rbc; /* Internal */
- uint iic_rxtmp; /* Internal */
- uint iic_tstate; /* Internal */
- uint iic_tdp; /* Internal */
- ushort iic_tbptr; /* Internal */
- ushort iic_tbc; /* Internal */
- uint iic_txtmp; /* Internal */
-} iic_t;
-
-#define BD_IIC_START ((ushort)0x0400)
-
-/* CPM interrupts. There are nearly 32 interrupts generated by CPM
- * channels or devices. All of these are presented to the PPC core
- * as a single interrupt. The CPM interrupt handler dispatches its
- * own handlers, in a similar fashion to the PPC core handler. We
- * use the table as defined in the manuals (i.e. no special high
- * priority and SCC1 == SCCa, etc...).
- */
-#define CPMVEC_NR 32
-#define CPMVEC_PIO_PC15 ((ushort)0x1f)
-#define CPMVEC_SCC1 ((ushort)0x1e)
-#define CPMVEC_SCC2 ((ushort)0x1d)
-#define CPMVEC_SCC3 ((ushort)0x1c)
-#define CPMVEC_SCC4 ((ushort)0x1b)
-#define CPMVEC_PIO_PC14 ((ushort)0x1a)
-#define CPMVEC_TIMER1 ((ushort)0x19)
-#define CPMVEC_PIO_PC13 ((ushort)0x18)
-#define CPMVEC_PIO_PC12 ((ushort)0x17)
-#define CPMVEC_SDMA_CB_ERR ((ushort)0x16)
-#define CPMVEC_IDMA1 ((ushort)0x15)
-#define CPMVEC_IDMA2 ((ushort)0x14)
-#define CPMVEC_TIMER2 ((ushort)0x12)
-#define CPMVEC_RISCTIMER ((ushort)0x11)
-#define CPMVEC_I2C ((ushort)0x10)
-#define CPMVEC_PIO_PC11 ((ushort)0x0f)
-#define CPMVEC_PIO_PC10 ((ushort)0x0e)
-#define CPMVEC_TIMER3 ((ushort)0x0c)
-#define CPMVEC_PIO_PC9 ((ushort)0x0b)
-#define CPMVEC_PIO_PC8 ((ushort)0x0a)
-#define CPMVEC_PIO_PC7 ((ushort)0x09)
-#define CPMVEC_TIMER4 ((ushort)0x07)
-#define CPMVEC_PIO_PC6 ((ushort)0x06)
-#define CPMVEC_SPI ((ushort)0x05)
-#define CPMVEC_SMC1 ((ushort)0x04)
-#define CPMVEC_SMC2 ((ushort)0x03)
-#define CPMVEC_PIO_PC5 ((ushort)0x02)
-#define CPMVEC_PIO_PC4 ((ushort)0x01)
-#define CPMVEC_ERROR ((ushort)0x00)
-
-/* CPM interrupt configuration vector.
-*/
-#define CICR_SCD_SCC4 ((uint)0x00c00000) /* SCC4 @ SCCd */
-#define CICR_SCC_SCC3 ((uint)0x00200000) /* SCC3 @ SCCc */
-#define CICR_SCB_SCC2 ((uint)0x00040000) /* SCC2 @ SCCb */
-#define CICR_SCA_SCC1 ((uint)0x00000000) /* SCC1 @ SCCa */
-#define CICR_IRL_MASK ((uint)0x0000e000) /* Core interrrupt */
-#define CICR_HP_MASK ((uint)0x00001f00) /* Hi-pri int. */
-#define CICR_IEN ((uint)0x00000080) /* Int. enable */
-#define CICR_SPS ((uint)0x00000001) /* SCC Spread */
-
-extern void cpm_install_handler(int vec,
- void (*handler)(void *, struct pt_regs *regs), void *dev_id);
-extern void cpm_free_handler(int vec);
-
-#endif /* __CPM_8XX__ */
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)