patch-2.1.85 linux/drivers/net/hamradio/Config.in

• Lines: 85
• Date: Mon Feb 2 15:18:15 1998
• Orig file: v2.1.84/linux/drivers/net/hamradio/Config.in
• Orig date: Sun Jan 4 10:40:16 1998

diff -u --recursive --new-file v2.1.84/linux/drivers/net/hamradio/Config.in linux/drivers/net/hamradio/Config.in
@@ -1,61 +1,27 @@
-#
-# Amateur Radio protocols and AX.25 device configuration
-#
-# 19971130	Now in an own category to make correct compilation of the 
-#		AX.25 stuff easier...
-#		Joerg Reuter DL1BKE <jreuter@poboxes.com>
+comment 'AX.25 network device drivers'
 
-mainmenu_option next_comment
-comment 'Amateur Radio support'
-bool 'Amateur Radio support' CONFIG_HAMRADIO
-
-if [ "$CONFIG_HAMRADIO" != "n" ] ; then
-  if [ "$CONFIG_NET" != "n" ] ; then
-    comment 'Packet Radio protocols'
-    tristate 'Amateur Radio AX.25 Level 2 protocol' CONFIG_AX25
-    if [ "$CONFIG_AX25" != "n" ]; then
-      bool '   AX.25 DAMA Slave support' CONFIG_AX25_DAMA_SLAVE
-#     bool '   AX.25 DAMA Master support' CONFIG_AX25_DAMA_MASTER
-      dep_tristate '   Amateur Radio NET/ROM protocol' CONFIG_NETROM $CONFIG_AX25
-      dep_tristate '   Amateur Radio X.25 PLP (Rose)' CONFIG_ROSE $CONFIG_AX25
-    fi
-    
-    if [ "$CONFIG_AX25" != "n" ]; then
-      comment 'AX.25 network device drivers'
-      tristate 'Serial port KISS driver' CONFIG_MKISS
-#     tristate 'Serial port 6PACK driver' CONFIG_6PACK
-      tristate 'BPQ Ethernet driver' CONFIG_BPQETHER
-    
-      dep_tristate 'High-speed (DMA) SCC driver for AX.25' CONFIG_DMASCC $CONFIG_AX25
-      tristate 'Z8530 SCC driver' CONFIG_SCC
-      if [ "$CONFIG_SCC" != "n" ]; then
-        bool '   additional delay for PA0HZP OptoSCC compatible boards' CONFIG_SCC_DELAY
-        bool '   support for TRX that feedback the tx signal to rx' CONFIG_SCC_TRXECHO
-      fi
+dep_tristate 'Serial port KISS driver' CONFIG_MKISS $CONFIG_AX25
+# dep_tristate 'Serial port 6PACK driver' CONFIG_6PACK $CONFIG_AX25
+dep_tristate 'BPQ Ethernet driver' CONFIG_BPQETHER $CONFIG_AX25
     
-      tristate 'BAYCOM ser12 fullduplex driver for AX.25' CONFIG_BAYCOM_SER_FDX
-      tristate 'BAYCOM ser12 halfduplex driver for AX.25' CONFIG_BAYCOM_SER_HDX
-      tristate 'BAYCOM picpar and par96 driver for AX.25' CONFIG_BAYCOM_PAR
-    
-      tristate 'Soundcard modem driver' CONFIG_SOUNDMODEM
-      if [ "$CONFIG_SOUNDMODEM" != "n" ]; then
-        bool '   soundmodem support for Soundblaster and compatible cards' CONFIG_SOUNDMODEM_SBC
-        bool '   soundmodem support for WSS and Crystal cards' CONFIG_SOUNDMODEM_WSS
-        bool '   soundmodem support for 1200 baud AFSK modulation' CONFIG_SOUNDMODEM_AFSK1200
-        bool '   soundmodem support for 2400 baud AFSK modulation (7.3728MHz crystal)' CONFIG_SOUNDMODEM_AFSK2400_7
-        bool '   soundmodem support for 2400 baud AFSK modulation (8MHz crystal)' CONFIG_SOUNDMODEM_AFSK2400_8
-        bool '   soundmodem support for 4800 baud HAPN-1 modulation' CONFIG_SOUNDMODEM_HAPN4800
-        bool '   soundmodem support for 9600 baud FSK G3RUH modulation' CONFIG_SOUNDMODEM_FSK9600
-      fi
-    fi
-  fi
-   
-  comment 'Misc. hamradio protocols'
-  tristate 'Shortwave radio modem driver' CONFIG_HFMODEM
-  if [ "$CONFIG_HFMODEM" != "n" ]; then
-    bool '   HFmodem support for Soundblaster and compatible cards' CONFIG_HFMODEM_SBC
-    bool '   HFmodem support for WSS and Crystal cards' CONFIG_HFMODEM_WSS
-  fi
+dep_tristate 'High-speed (DMA) SCC driver for AX.25' CONFIG_DMASCC $CONFIG_AX25
+dep_tristate 'Z8530 SCC driver' CONFIG_SCC $CONFIG_AX25
+if [ "$CONFIG_SCC" != "n" ]; then
+  bool '   additional delay for PA0HZP OptoSCC compatible boards' CONFIG_SCC_DELAY
+  bool '   support for TRX that feedback the tx signal to rx' CONFIG_SCC_TRXECHO
 fi
+    
+dep_tristate 'BAYCOM ser12 fullduplex driver for AX.25' CONFIG_BAYCOM_SER_FDX $CONFIG_AX25
+dep_tristate 'BAYCOM ser12 halfduplex driver for AX.25' CONFIG_BAYCOM_SER_HDX $CONFIG_AX25
+dep_tristate 'BAYCOM picpar and par96 driver for AX.25' CONFIG_BAYCOM_PAR $CONFIG_AX25
 
-endmenu
+dep_tristate 'Soundcard modem driver' CONFIG_SOUNDMODEM $CONFIG_AX25
+if [ "$CONFIG_SOUNDMODEM" != "n" ]; then
+  bool '   soundmodem support for Soundblaster and compatible cards' CONFIG_SOUNDMODEM_SBC
+  bool '   soundmodem support for WSS and Crystal cards' CONFIG_SOUNDMODEM_WSS
+  bool '   soundmodem support for 1200 baud AFSK modulation' CONFIG_SOUNDMODEM_AFSK1200
+  bool '   soundmodem support for 2400 baud AFSK modulation (7.3728MHz crystal)' CONFIG_SOUNDMODEM_AFSK2400_7
+  bool '   soundmodem support for 2400 baud AFSK modulation (8MHz crystal)' CONFIG_SOUNDMODEM_AFSK2400_8
+  bool '   soundmodem support for 4800 baud HAPN-1 modulation' CONFIG_SOUNDMODEM_HAPN4800
+  bool '   soundmodem support for 9600 baud FSK G3RUH modulation' CONFIG_SOUNDMODEM_FSK9600
+fi