patch-2.1.16 linux/include/asm-sparc64/dma.h

Next file: linux/include/asm-sparc64/elf.h
Previous file: linux/include/asm-sparc64/delay.h
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.1.15/linux/include/asm-sparc64/dma.h linux/include/asm-sparc64/dma.h
@@ -0,0 +1,209 @@
+/* $Id: dma.h,v 1.1 1996/11/20 15:27:38 davem Exp $
+ * include/asm-sparc64/dma.h
+ *
+ * Copyright 1995 (C) David S. Miller (davem@caip.rutgers.edu)
+ */
+
+#ifndef _ASM_SPARC64_DMA_H
+#define _ASM_SPARC64_DMA_H
+
+#include <linux/kernel.h>
+
+#include <asm/vac-ops.h>  /* for invalidate's, etc. */
+#include <asm/sbus.h>
+#include <asm/delay.h>
+#include <asm/oplib.h>
+
+/* These are irrelevant for Sparc DMA, but we leave it in so that
+ * things can compile.
+ */
+#define MAX_DMA_CHANNELS 8
+#define MAX_DMA_ADDRESS  (~0UL)
+#define DMA_MODE_READ    1
+#define DMA_MODE_WRITE   2
+
+/* Useful constants */
+#define SIZE_16MB      (16*1024*1024)
+#define SIZE_64K       (64*1024)
+
+/* Structure to describe the current status of DMA registers on the Sparc */
+struct sparc_dma_registers {
+  __volatile__ unsigned int cond_reg;   /* DMA condition register */
+  __volatile__ char * st_addr;          /* Start address of this transfer */
+  __volatile__ unsigned int cnt;        /* How many bytes to transfer */
+  __volatile__ unsigned int dma_test;   /* DMA test register */
+};
+
+/* DVMA chip revisions */
+enum dvma_rev {
+	dvmarev0,
+	dvmaesc1,
+	dvmarev1,
+	dvmarev2,
+	dvmarev3,
+	dvmarevplus,
+	dvmahme
+};
+
+#define DMA_HASCOUNT(rev)  ((rev)==dvmaesc1)
+
+/* Linux DMA information structure, filled during probe. */
+struct Linux_SBus_DMA {
+	struct Linux_SBus_DMA *next;
+	struct linux_sbus_device *SBus_dev;
+	struct sparc_dma_registers *regs;
+
+	/* Status, misc info */
+	int node;                /* Prom node for this DMA device */
+	int running;             /* Are we doing DMA now? */
+	int allocated;           /* Are we "owned" by anyone yet? */
+
+	/* Transfer information. */
+	unsigned int addr;       /* Start address of current transfer */
+	int nbytes;              /* Size of current transfer */
+	int realbytes;           /* For splitting up large transfers, etc. */
+
+	/* DMA revision */
+	enum dvma_rev revision;
+};
+
+extern struct Linux_SBus_DMA *dma_chain;
+
+/* Broken hardware... */
+#define DMA_ISBROKEN(dma)    ((dma)->revision == dvmarev1)
+#define DMA_ISESC1(dma)      ((dma)->revision == dvmaesc1)
+
+/* Main routines in dma.c */
+extern void dump_dma_regs(struct sparc_dma_registers *);
+extern unsigned long dvma_init(struct linux_sbus *, unsigned long);
+
+/* Fields in the cond_reg register */
+/* First, the version identification bits */
+#define DMA_DEVICE_ID    0xf0000000        /* Device identification bits */
+#define DMA_VERS0        0x00000000        /* Sunray DMA version */
+#define DMA_ESCV1        0x40000000        /* DMA ESC Version 1 */
+#define DMA_VERS1        0x80000000        /* DMA rev 1 */
+#define DMA_VERS2        0xa0000000        /* DMA rev 2 */
+#define DMA_VERHME       0xb0000000        /* DMA hme gate array */
+#define DMA_VERSPLUS     0x90000000        /* DMA rev 1 PLUS */
+
+#define DMA_HNDL_INTR    0x00000001        /* An IRQ needs to be handled */
+#define DMA_HNDL_ERROR   0x00000002        /* We need to take an error */
+#define DMA_FIFO_ISDRAIN 0x0000000c        /* The DMA FIFO is draining */
+#define DMA_INT_ENAB     0x00000010        /* Turn on interrupts */
+#define DMA_FIFO_INV     0x00000020        /* Invalidate the FIFO */
+#define DMA_ACC_SZ_ERR   0x00000040        /* The access size was bad */
+#define DMA_FIFO_STDRAIN 0x00000040        /* DMA_VERS1 Drain the FIFO */
+#define DMA_RST_SCSI     0x00000080        /* Reset the SCSI controller */
+#define DMA_RST_ENET     DMA_RST_SCSI      /* Reset the ENET controller */
+#define DMA_ST_WRITE     0x00000100        /* write from device to memory */
+#define DMA_ENABLE       0x00000200        /* Fire up DMA, handle requests */
+#define DMA_PEND_READ    0x00000400        /* DMA_VERS1/0/PLUS Pending Read */
+#define DMA_ESC_BURST    0x00000800        /* 1=16byte 0=32byte */
+#define DMA_READ_AHEAD   0x00001800        /* DMA read ahead partial longword */
+#define DMA_DSBL_RD_DRN  0x00001000        /* No EC drain on slave reads */
+#define DMA_BCNT_ENAB    0x00002000        /* If on, use the byte counter */
+#define DMA_TERM_CNTR    0x00004000        /* Terminal counter */
+#define DMA_CSR_DISAB    0x00010000        /* No FIFO drains during csr */
+#define DMA_SCSI_DISAB   0x00020000        /* No FIFO drains during reg */
+#define DMA_DSBL_WR_INV  0x00020000        /* No EC inval. on slave writes */
+#define DMA_ADD_ENABLE   0x00040000        /* Special ESC DVMA optimization */
+#define DMA_E_BURST8	 0x00040000	   /* ENET: SBUS r/w burst size */
+#define DMA_BRST_SZ      0x000c0000        /* SCSI: SBUS r/w burst size */
+#define DMA_BRST64       0x00080000        /* SCSI: 64byte bursts (HME on UltraSparc only) */
+#define DMA_BRST32       0x00040000        /* SCSI: 32byte bursts */
+#define DMA_BRST16       0x00000000        /* SCSI: 16byte bursts */
+#define DMA_BRST0        0x00080000        /* SCSI: no bursts (non-HME gate arrays) */
+#define DMA_ADDR_DISAB   0x00100000        /* No FIFO drains during addr */
+#define DMA_2CLKS        0x00200000        /* Each transfer = 2 clock ticks */
+#define DMA_3CLKS        0x00400000        /* Each transfer = 3 clock ticks */
+#define DMA_EN_ENETAUI   DMA_3CLKS         /* Put lance into AUI-cable mode */
+#define DMA_CNTR_DISAB   0x00800000        /* No IRQ when DMA_TERM_CNTR set */
+#define DMA_AUTO_NADDR   0x01000000        /* Use "auto nxt addr" feature */
+#define DMA_SCSI_ON      0x02000000        /* Enable SCSI dma */
+#define DMA_PARITY_OFF   0x02000000        /* HME: disable parity checking */
+#define DMA_LOADED_ADDR  0x04000000        /* Address has been loaded */
+#define DMA_LOADED_NADDR 0x08000000        /* Next address has been loaded */
+
+/* Values describing the burst-size property from the PROM */
+#define DMA_BURST1       0x01
+#define DMA_BURST2       0x02
+#define DMA_BURST4       0x04
+#define DMA_BURST8       0x08
+#define DMA_BURST16      0x10
+#define DMA_BURST32      0x20
+#define DMA_BURST64      0x40
+#define DMA_BURSTBITS    0x7f
+
+/* Determine highest possible final transfer address given a base */
+#define DMA_MAXEND(addr) (0x01000000UL-(((unsigned long)(addr))&0x00ffffffUL))
+
+/* Yes, I hack a lot of elisp in my spare time... */
+#define DMA_ERROR_P(regs)  ((((regs)->cond_reg) & DMA_HNDL_ERROR))
+#define DMA_IRQ_P(regs)    ((((regs)->cond_reg) & (DMA_HNDL_INTR | DMA_HNDL_ERROR)))
+#define DMA_WRITE_P(regs)  ((((regs)->cond_reg) & DMA_ST_WRITE))
+#define DMA_OFF(regs)      ((((regs)->cond_reg) &= (~DMA_ENABLE)))
+#define DMA_INTSOFF(regs)  ((((regs)->cond_reg) &= (~DMA_INT_ENAB)))
+#define DMA_INTSON(regs)   ((((regs)->cond_reg) |= (DMA_INT_ENAB)))
+#define DMA_PUNTFIFO(regs) ((((regs)->cond_reg) |= DMA_FIFO_INV))
+#define DMA_SETSTART(regs, addr)  ((((regs)->st_addr) = (char *) addr))
+#define DMA_BEGINDMA_W(regs) \
+        ((((regs)->cond_reg |= (DMA_ST_WRITE|DMA_ENABLE|DMA_INT_ENAB))))
+#define DMA_BEGINDMA_R(regs) \
+        ((((regs)->cond_reg |= ((DMA_ENABLE|DMA_INT_ENAB)&(~DMA_ST_WRITE)))))
+
+/* For certain DMA chips, we need to disable ints upon irq entry
+ * and turn them back on when we are done.  So in any ESP interrupt
+ * handler you *must* call DMA_IRQ_ENTRY upon entry and DMA_IRQ_EXIT
+ * when leaving the handler.  You have been warned...
+ */
+#define DMA_IRQ_ENTRY(dma, dregs) do { \
+        if(DMA_ISBROKEN(dma)) DMA_INTSOFF(dregs); \
+   } while (0)
+
+#define DMA_IRQ_EXIT(dma, dregs) do { \
+	if(DMA_ISBROKEN(dma)) DMA_INTSON(dregs); \
+   } while(0)
+
+/* Pause until counter runs out or BIT isn't set in the DMA condition
+ * register.
+ */
+extern __inline__ void sparc_dma_pause(struct sparc_dma_registers *regs,
+				       unsigned long bit)
+{
+	int ctr = 50000;   /* Let's find some bugs ;) */
+
+	/* Busy wait until the bit is not set any more */
+	while((regs->cond_reg&bit) && (ctr>0)) {
+		ctr--;
+		__delay(5);
+	}
+
+	/* Check for bogus outcome. */
+	if(!ctr)
+		panic("DMA timeout");
+}
+
+/* Reset the friggin' thing... */
+#define DMA_RESET(dma) do { \
+	struct sparc_dma_registers *regs = dma->regs;                      \
+	/* Let the current FIFO drain itself */                            \
+	sparc_dma_pause(regs, (DMA_FIFO_ISDRAIN));                         \
+	/* Reset the logic */                                              \
+	regs->cond_reg |= (DMA_RST_SCSI);     /* assert */                 \
+	__delay(400);                         /* let the bits set ;) */    \
+	regs->cond_reg &= ~(DMA_RST_SCSI);    /* de-assert */              \
+	sparc_dma_enable_interrupts(regs);    /* Re-enable interrupts */   \
+	/* Enable FAST transfers if available */                           \
+	if(dma->revision>dvmarev1) regs->cond_reg |= DMA_3CLKS;            \
+	dma->running = 0;                                                  \
+} while(0)
+
+#define for_each_dvma(dma) \
+        for((dma) = dma_chain; (dma); (dma) = (dma)->next)
+
+extern int get_dma_list(char *);
+extern int request_dma(unsigned int, __const__ char *);
+extern void free_dma(unsigned int);
+
+#endif /* !(_ASM_SPARC64_DMA_H) */

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov