patch-2.1.125 linux/drivers/net/ne3210.c

• Lines: 433
• Date: Wed Oct 7 15:51:45 1998
• Orig file: v2.1.124/linux/drivers/net/ne3210.c
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.1.124/linux/drivers/net/ne3210.c linux/drivers/net/ne3210.c
@@ -0,0 +1,432 @@
+/*
+	ne3210.c
+
+	Linux driver for Novell NE3210 EISA Network Adapter
+
+	Copyright (C) 1998, Paul Gortmaker.
+
+	This software may be used and distributed according to the terms
+	of the GNU Public License, incorporated herein by reference.
+
+	Information and Code Sources:
+
+	1) Based upon my other EISA 8390 drivers (lne390, es3210, smc-ultra32)
+	2) The existing myriad of other Linux 8390 drivers by Donald Becker.
+	3) Info for getting IRQ and sh-mem gleaned from the EISA cfg file
+
+	The NE3210 is an EISA shared memory NS8390 implementation.  Shared 
+	memory address > 1MB should work with this driver.
+
+	Note that the .cfg file (3/11/93, v1.0) has AUI and BNC switched 
+	around (or perhaps there are some defective/backwards cards ???)
+
+	This driver WILL NOT WORK FOR THE NE3200 - it is completely different
+	and does not use an 8390 at all.
+
+*/
+
+static const char *version =
+	"ne3210.c: Driver revision v0.03, 30/09/98\n";
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+#include <asm/system.h>
+
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include "8390.h"
+
+int ne3210_probe(struct device *dev);
+int ne3210_probe1(struct device *dev, int ioaddr);
+
+static int ne3210_open(struct device *dev);
+static int ne3210_close(struct device *dev);
+
+static void ne3210_reset_8390(struct device *dev);
+
+static void ne3210_get_8390_hdr(struct device *dev, struct e8390_pkt_hdr *hdr, int ring_page);
+static void ne3210_block_input(struct device *dev, int count, struct sk_buff *skb, int ring_offset);
+static void ne3210_block_output(struct device *dev, int count, const unsigned char *buf, const int start_page);
+
+#define NE3210_START_PG		0x00    /* First page of TX buffer	*/
+#define NE3210_STOP_PG		0x80    /* Last page +1 of RX ring	*/
+
+#define NE3210_ID_PORT		0xc80	/* Same for all EISA cards 	*/
+#define NE3210_IO_EXTENT	0x20
+#define NE3210_SA_PROM		0x16	/* Start of e'net addr.		*/
+#define NE3210_RESET_PORT	0xc84
+#define NE3210_NIC_OFFSET	0x00	/* Hello, the 8390 is *here*	*/
+
+#define NE3210_ADDR0		0x00	/* 3 byte vendor prefix		*/
+#define NE3210_ADDR1		0x00
+#define NE3210_ADDR2		0x1b
+
+#define NE3210_ID	0x0118cc3a	/* 0x3acc = 1110 10110 01100 =  nvl */
+
+#define NE3210_CFG1		0xc84	/* NB: 0xc84 is also "reset" port. */
+#define NE3210_CFG2		0xc90
+
+/*
+ *	You can OR any of the following bits together and assign it
+ *	to NE3210_DEBUG to get verbose driver info during operation.
+ *	Currently only the probe one is implemented.
+ */
+
+#define NE3210_D_PROBE	0x01
+#define NE3210_D_RX_PKT	0x02
+#define NE3210_D_TX_PKT	0x04
+#define NE3210_D_IRQ	0x08
+
+#define NE3210_DEBUG	0x0
+
+static unsigned char irq_map[] __initdata = {15, 12, 11, 10, 9, 7, 5, 3};
+static unsigned int shmem_map[] __initdata = {0xff0, 0xfe0, 0xfff0, 0xd8, 0xffe0, 0xffc0, 0xd0, 0x0};
+
+/*
+ *	Probe for the card. The best way is to read the EISA ID if it
+ *	is known. Then we can check the prefix of the station address
+ *	PROM for a match against the value assigned to Novell.
+ */
+
+__initfunc(int ne3210_probe(struct device *dev))
+{
+	unsigned short ioaddr = dev->base_addr;
+
+	if (ioaddr > 0x1ff)		/* Check a single specified location. */
+		return ne3210_probe1(dev, ioaddr);
+	else if (ioaddr > 0)		/* Don't probe at all. */
+		return ENXIO;
+
+	if (!EISA_bus) {
+#if NE3210_DEBUG & NE3210_D_PROBE
+		printk("ne3210-debug: Not an EISA bus. Not probing high ports.\n");
+#endif
+		return ENXIO;
+	}
+
+	/* EISA spec allows for up to 16 slots, but 8 is typical. */
+	for (ioaddr = 0x1000; ioaddr < 0x9000; ioaddr += 0x1000) {
+		if (check_region(ioaddr , NE3210_IO_EXTENT))
+			continue;
+		if (ne3210_probe1(dev, ioaddr) == 0)
+			return 0;
+	}
+
+	return ENODEV;
+}
+
+__initfunc(int ne3210_probe1(struct device *dev, int ioaddr))
+{
+	int i;
+	unsigned long eisa_id;
+	const char *ifmap[] = {"UTP", "?", "BNC", "AUI"};
+
+	if (inb_p(ioaddr + NE3210_ID_PORT) == 0xff) return -ENODEV;
+
+#if NE3210_DEBUG & NE3210_D_PROBE
+	printk("ne3210-debug: probe at %#x, ID %#8x\n", ioaddr, inl(ioaddr + NE3210_ID_PORT));
+	printk("ne3210-debug: config regs: %#x %#x\n",
+		inb(ioaddr + NE3210_CFG1), inb(ioaddr + NE3210_CFG2));
+#endif
+
+
+/*	Check the EISA ID of the card. */
+	eisa_id = inl(ioaddr + NE3210_ID_PORT);
+	if (eisa_id != NE3210_ID) {
+		return ENODEV;
+	}
+
+	
+#if 0
+/*	Check the vendor ID as well. Not really required. */
+	if (inb(ioaddr + NE3210_SA_PROM + 0) != NE3210_ADDR0
+		|| inb(ioaddr + NE3210_SA_PROM + 1) != NE3210_ADDR1
+		|| inb(ioaddr + NE3210_SA_PROM + 2) != NE3210_ADDR2 ) {
+		printk("ne3210.c: card not found");
+		for(i = 0; i < ETHER_ADDR_LEN; i++)
+			printk(" %02x", inb(ioaddr + NE3210_SA_PROM + i));
+		printk(" (invalid prefix).\n");
+		return ENODEV;
+	}
+#endif
+
+	if (load_8390_module("ne3210.c"))
+		return -ENOSYS;
+
+	/* We should have a "dev" from Space.c or the static module table. */
+	if (dev == NULL) {
+		printk("ne3210.c: Passed a NULL device.\n");
+		dev = init_etherdev(0, 0);
+	}
+
+	/* Allocate dev->priv and fill in 8390 specific dev fields. */
+	if (ethdev_init(dev)) {
+		printk ("ne3210.c: unable to allocate memory for dev->priv!\n");
+		return -ENOMEM;
+	}
+
+	printk("ne3210.c: NE3210 in EISA slot %d, media: %s, addr:",
+		ioaddr/0x1000, ifmap[inb(ioaddr + NE3210_CFG2) >> 6]);
+	for(i = 0; i < ETHER_ADDR_LEN; i++)
+		printk(" %02x", (dev->dev_addr[i] = inb(ioaddr + NE3210_SA_PROM + i)));
+	printk(".\nne3210.c: ");
+
+	/* Snarf the interrupt now. CFG file has them all listed as `edge' with share=NO */
+	if (dev->irq == 0) {
+		unsigned char irq_reg = inb(ioaddr + NE3210_CFG2) >> 3;
+		dev->irq = irq_map[irq_reg & 0x07];
+		printk("using");
+	} else {
+		/* This is useless unless we reprogram the card here too */
+		if (dev->irq == 2) dev->irq = 9;	/* Doh! */
+		printk("assigning");
+	}
+	printk(" IRQ %d,", dev->irq);
+
+	if (request_irq(dev->irq, ei_interrupt, 0, "ne3210", dev)) {
+		printk (" unable to get IRQ %d.\n", dev->irq);
+		kfree(dev->priv);
+		dev->priv = NULL;
+		return EAGAIN;
+	}
+
+	if (dev->mem_start == 0) {
+		unsigned char mem_reg = inb(ioaddr + NE3210_CFG2) & 0x07;
+		dev->mem_start = shmem_map[mem_reg] * 0x1000;
+		printk(" using ");
+	} else {
+		/* Should check for value in shmem_map and reprogram the card to use it */
+		dev->mem_start &= 0xfff8000;
+		printk(" assigning ");
+	}
+
+	printk("%dkB memory at physical address %#lx\n",
+			NE3210_STOP_PG/4, dev->mem_start);
+
+	/*
+	   BEWARE!! Some dain-bramaged EISA SCUs will allow you to put
+	   the card mem within the region covered by `normal' RAM  !!!
+	*/
+	if (dev->mem_start > 1024*1024) {	/* phys addr > 1MB */
+		if (dev->mem_start < virt_to_bus(high_memory)) {
+			printk(KERN_CRIT "ne3210.c: Card RAM overlaps with normal memory!!!\n");
+			printk(KERN_CRIT "ne3210.c: Use EISA SCU to set card memory below 1MB,\n");
+			printk(KERN_CRIT "ne3210.c: or to an address above 0x%lx.\n", virt_to_bus(high_memory));
+			printk(KERN_CRIT "ne3210.c: Driver NOT installed.\n");
+			free_irq(dev->irq, dev);
+			kfree(dev->priv);
+			dev->priv = NULL;
+			return EINVAL;
+		}
+		dev->mem_start = (unsigned long)ioremap(dev->mem_start, NE3210_STOP_PG*0x100);
+		if (dev->mem_start == 0) {
+			printk(KERN_ERR "ne3210.c: Unable to remap card memory above 1MB !!\n");
+			printk(KERN_ERR "ne3210.c: Try using EISA SCU to set memory below 1MB.\n");
+			printk(KERN_ERR "ne3210.c: Driver NOT installed.\n");
+			free_irq(dev->irq, dev);
+			kfree(dev->priv);
+			dev->priv = NULL;
+			return EAGAIN;
+		}
+		ei_status.reg0 = 1;	/* Use as remap flag */
+		printk("ne3210.c: remapped %dkB card memory to virtual address %#lx\n",
+				NE3210_STOP_PG/4, dev->mem_start);
+	}
+
+	dev->mem_end = dev->rmem_end = dev->mem_start
+		+ (NE3210_STOP_PG - NE3210_START_PG)*256;
+	dev->rmem_start = dev->mem_start + TX_PAGES*256;
+
+	/* The 8390 offset is zero for the NE3210 */
+	dev->base_addr = ioaddr;
+	request_region(dev->base_addr, NE3210_IO_EXTENT, "ne3210");
+
+	ei_status.name = "NE3210";
+	ei_status.tx_start_page = NE3210_START_PG;
+	ei_status.rx_start_page = NE3210_START_PG + TX_PAGES;
+	ei_status.stop_page = NE3210_STOP_PG;
+	ei_status.word16 = 1;
+
+	if (ei_debug > 0)
+		printk(version);
+
+	ei_status.reset_8390 = &ne3210_reset_8390;
+	ei_status.block_input = &ne3210_block_input;
+	ei_status.block_output = &ne3210_block_output;
+	ei_status.get_8390_hdr = &ne3210_get_8390_hdr;
+
+	dev->open = &ne3210_open;
+	dev->stop = &ne3210_close;
+	NS8390_init(dev, 0);
+	return 0;
+}
+
+/*
+ *	Reset by toggling the "Board Enable" bits (bit 2 and 0).
+ */
+
+static void ne3210_reset_8390(struct device *dev)
+{
+	unsigned short ioaddr = dev->base_addr;
+
+	outb(0x04, ioaddr + NE3210_RESET_PORT);
+	if (ei_debug > 1) printk("%s: resetting the NE3210...", dev->name);
+
+	mdelay(2);
+
+	ei_status.txing = 0;
+	outb(0x01, ioaddr + NE3210_RESET_PORT);
+	if (ei_debug > 1) printk("reset done\n");
+
+	return;
+}
+
+/*
+ *	Note: In the following three functions is the implicit assumption
+ *	that the associated memcpy will only use "rep; movsl" as long as
+ *	we keep the counts as some multiple of doublewords. This is a
+ *	requirement of the hardware, and also prevents us from using
+ *	eth_io_copy_and_sum() since we can't guarantee it will limit
+ *	itself to doubleword access.
+ */
+
+/*
+ *	Grab the 8390 specific header. Similar to the block_input routine, but
+ *	we don't need to be concerned with ring wrap as the header will be at
+ *	the start of a page, so we optimize accordingly. (A single doubleword.)
+ */
+
+static void
+ne3210_get_8390_hdr(struct device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
+{
+	unsigned long hdr_start = dev->mem_start + ((ring_page - NE3210_START_PG)<<8);
+	memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr));
+	hdr->count = (hdr->count + 3) & ~3;     /* Round up allocation. */
+}
+
+/*	
+ *	Block input and output are easy on shared memory ethercards, the only
+ *	complication is when the ring buffer wraps. The count will already
+ *	be rounded up to a doubleword value via ne3210_get_8390_hdr() above.
+ */
+
+static void ne3210_block_input(struct device *dev, int count, struct sk_buff *skb,
+						  int ring_offset)
+{
+	unsigned long xfer_start = dev->mem_start + ring_offset - (NE3210_START_PG<<8);
+
+	if (xfer_start + count > dev->rmem_end) {
+		/* Packet wraps over end of ring buffer. */
+		int semi_count = dev->rmem_end - xfer_start;
+		memcpy_fromio(skb->data, xfer_start, semi_count);
+		count -= semi_count;
+		memcpy_fromio(skb->data + semi_count, dev->rmem_start, count);
+	} else {
+		/* Packet is in one chunk. */
+		memcpy_fromio(skb->data, xfer_start, count);
+	}
+}
+
+static void ne3210_block_output(struct device *dev, int count,
+				const unsigned char *buf, int start_page)
+{
+	unsigned long shmem = dev->mem_start + ((start_page - NE3210_START_PG)<<8);
+
+	count = (count + 3) & ~3;     /* Round up to doubleword */
+	memcpy_toio(shmem, buf, count);
+}
+
+static int ne3210_open(struct device *dev)
+{
+	ei_open(dev);
+	MOD_INC_USE_COUNT;
+	return 0;
+}
+
+static int ne3210_close(struct device *dev)
+{
+
+	if (ei_debug > 1)
+		printk("%s: Shutting down ethercard.\n", dev->name);
+
+	ei_close(dev);
+	MOD_DEC_USE_COUNT;
+	return 0;
+}
+
+#ifdef MODULE
+#define MAX_NE3210_CARDS	4	/* Max number of NE3210 cards per module */
+#define NAMELEN			8	/* # of chars for storing dev->name */
+static char namelist[NAMELEN * MAX_NE3210_CARDS] = { 0, };
+static struct device dev_ne3210[MAX_NE3210_CARDS] = {
+	{
+		NULL,		/* assign a chunk of namelist[] below */
+		0, 0, 0, 0,
+		0, 0,
+		0, 0, 0, NULL, NULL
+	},
+};
+
+static int io[MAX_NE3210_CARDS] = { 0, };
+static int irq[MAX_NE3210_CARDS]  = { 0, };
+static int mem[MAX_NE3210_CARDS] = { 0, };
+
+MODULE_PARM(io, "1-" __MODULE_STRING(MAX_NE3210_CARDS) "i");
+MODULE_PARM(irq, "1-" __MODULE_STRING(MAX_NE3210_CARDS) "i");
+MODULE_PARM(mem, "1-" __MODULE_STRING(MAX_NE3210_CARDS) "i");
+
+int init_module(void)
+{
+	int this_dev, found = 0;
+
+	for (this_dev = 0; this_dev < MAX_NE3210_CARDS; this_dev++) {
+		struct device *dev = &dev_ne3210[this_dev];
+		dev->name = namelist+(NAMELEN*this_dev);
+		dev->irq = irq[this_dev];
+		dev->base_addr = io[this_dev];
+		dev->mem_start = mem[this_dev];
+		dev->init = ne3210_probe;
+		/* Default is to only install one card. */
+		if (io[this_dev] == 0 && this_dev != 0) break;
+		if (register_netdev(dev) != 0) {
+			printk(KERN_WARNING "ne3210.c: No NE3210 card found (i/o = 0x%x).\n", io[this_dev]);
+			if (found != 0) {	/* Got at least one. */
+				lock_8390_module();
+				return 0;
+			}
+			return -ENXIO;
+		}
+		found++;
+	}
+	lock_8390_module();
+	return 0;
+}
+
+void cleanup_module(void)
+{
+	int this_dev;
+
+	for (this_dev = 0; this_dev < MAX_NE3210_CARDS; this_dev++) {
+		struct device *dev = &dev_ne3210[this_dev];
+		if (dev->priv != NULL) {
+			void *priv = dev->priv;
+			free_irq(dev->irq, dev);
+			release_region(dev->base_addr, NE3210_IO_EXTENT);
+			if (ei_status.reg0)
+				iounmap((void *)dev->mem_start);
+			dev->priv = NULL;
+			unregister_netdev(dev);
+			kfree(priv);
+		}
+	}
+	unlock_8390_module();
+}
+#endif /* MODULE */
+