patch-2.1.113 linux/include/linux/debugreg.h

Next file: linux/include/linux/kd.h
Previous file: linux/include/linux/console_struct.h
Back to the patch index
Back to the overall index

diff -u --recursive --new-file v2.1.112/linux/include/linux/debugreg.h linux/include/linux/debugreg.h
@@ -1,61 +0,0 @@
-#ifndef _LINUX_DEBUGREG_H
-#define _LINUX_DEBUGREG_H
-
-
-/* Indicate the register numbers for a number of the specific
-   debug registers.  Registers 0-3 contain the addresses we wish to trap on */
-#define DR_FIRSTADDR 0        /* u_debugreg[DR_FIRSTADDR] */
-#define DR_LASTADDR 3         /* u_debugreg[DR_LASTADDR]  */
-
-#define DR_STATUS 6           /* u_debugreg[DR_STATUS]     */
-#define DR_CONTROL 7          /* u_debugreg[DR_CONTROL] */
-
-/* Define a few things for the status register.  We can use this to determine
-   which debugging register was responsible for the trap.  The other bits
-   are either reserved or not of interest to us. */
-
-#define DR_TRAP0 (0x1) /* Trap due to db0 */
-#define DR_TRAP1 (0x2) /* Trap due to db1 */
-#define DR_TRAP2 (0x4) /* Trap due to db2 */
-#define DR_TRAP3 (0x8) /* Trap due to db3 */
-
-/* Now define a bunch of things for manipulating the control register.
-   The top two bytes of the control register consist of 4 fields of 4
-   bits - each field corresponds to one of the four debug registers,
-   and indicates what types of access we trap on, and how large the data
-   field is that we are looking at */
-
-#define DR_CONTROL_SHIFT 16 /* Skip this many bits in ctl register */
-#define DR_CONTROL_SIZE 4   /* 4 control bits per register */
-
-#define DR_RW_EXECUTE (0x0)   /* Settings for the access types to trap on */
-#define DR_RW_WRITE (0x1)
-#define DR_RW_READ (0x3)
-
-#define DR_LEN_1 (0x0) /* Settings for data length to trap on */
-#define DR_LEN_2 (0x4)
-#define DR_LEN_4 (0xC)
-
-/* The low byte to the control register determine which registers are
-   enabled.  There are 4 fields of two bits.  One bit is "local", meaning
-   that the processor will reset the bit after a task switch and the other
-   is global meaning that we have to explicitly reset the bit.  With linux,
-   you can use either one, since we explicitly zero the register when we enter
-   kernel mode. */
-
-#define DR_LOCAL_ENABLE_SHIFT 0    /* Extra shift to the local enable bit */
-#define DR_GLOBAL_ENABLE_SHIFT 1   /* Extra shift to the global enable bit */
-#define DR_ENABLE_SIZE 2           /* 2 enable bits per register */
-
-#define DR_LOCAL_ENABLE_MASK (0x55)  /* Set  local bits for all 4 regs */
-#define DR_GLOBAL_ENABLE_MASK (0xAA) /* Set global bits for all 4 regs */
-
-/* The second byte to the control register has a few special things.
-   We can slow the instruction pipeline for instructions coming via the
-   gdt or the ldt if we want to.  I am not sure why this is an advantage */
-
-#define DR_CONTROL_RESERVED (0xFC00) /* Reserved by Intel */
-#define DR_LOCAL_SLOWDOWN (0x100)   /* Local slow the pipeline */
-#define DR_GLOBAL_SLOWDOWN (0x200)  /* Global slow the pipeline */
-
-#endif

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen, slshen@lbl.gov