From: Matt Porter <mporter@kernel.crashing.org>
This patch adds a field to struct ocp_func_emac_data that allows
platform-specific unsupported PHY features to be passed in to the ibm_emac
ethernet driver.
This patch also adds some logic for the Bamboo eval board to populate this
field based on the dip switches on the board. This is a workaround for the
improperly biased RJ-45 sockets on the Rev. 0 Bamboo.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
---
arch/ppc/platforms/4xx/bamboo.c | 52 +++++++++++++++++++++++++++++++++-------
include/asm-ppc/ibm_ocp.h | 1
2 files changed, 45 insertions(+), 8 deletions(-)
diff -puN arch/ppc/platforms/4xx/bamboo.c~ppc32-add-phy-excluded-features-to-ocp_func_emac_data arch/ppc/platforms/4xx/bamboo.c
--- 25/arch/ppc/platforms/4xx/bamboo.c~ppc32-add-phy-excluded-features-to-ocp_func_emac_data Wed Aug 17 14:17:15 2005
+++ 25-akpm/arch/ppc/platforms/4xx/bamboo.c Wed Aug 17 14:17:15 2005
@@ -123,33 +123,69 @@ bamboo_map_irq(struct pci_dev *dev, unsi
static void __init bamboo_set_emacdata(void)
{
- unsigned char * selection1_base;
+ u8 * base_addr;
struct ocp_def *def;
struct ocp_func_emac_data *emacdata;
- u8 selection1_val;
+ u8 val;
int mode;
+ u32 excluded = 0;
- selection1_base = ioremap64(BAMBOO_FPGA_SELECTION1_REG_ADDR, 16);
- selection1_val = readb(selection1_base);
- iounmap((void *) selection1_base);
- if (BAMBOO_SEL_MII(selection1_val))
+ base_addr = ioremap64(BAMBOO_FPGA_SELECTION1_REG_ADDR, 16);
+ val = readb(base_addr);
+ iounmap((void *) base_addr);
+ if (BAMBOO_SEL_MII(val))
mode = PHY_MODE_MII;
- else if (BAMBOO_SEL_RMII(selection1_val))
+ else if (BAMBOO_SEL_RMII(val))
mode = PHY_MODE_RMII;
else
mode = PHY_MODE_SMII;
- /* Set mac_addr and phy mode for each EMAC */
+ /*
+ * SW2 on the Bamboo is used for ethernet configuration and is accessed
+ * via the CONFIG2 register in the FPGA. If the ANEG pin is set,
+ * overwrite the supported features with the settings in SW2.
+ *
+ * This is used as a workaround for the improperly biased RJ-45 sockets
+ * on the Rev. 0 Bamboo. By default only 10baseT is functional.
+ * Removing inductors L17 and L18 from the board allows 100baseT, but
+ * disables 10baseT. The Rev. 1 has no such limitations.
+ */
+
+ base_addr = ioremap64(BAMBOO_FPGA_CONFIG2_REG_ADDR, 8);
+ val = readb(base_addr);
+ iounmap((void *) base_addr);
+ if (!BAMBOO_AUTONEGOTIATE(val)) {
+ excluded |= SUPPORTED_Autoneg;
+ if (BAMBOO_FORCE_100Mbps(val)) {
+ excluded |= SUPPORTED_10baseT_Full;
+ excluded |= SUPPORTED_10baseT_Half;
+ if (BAMBOO_FULL_DUPLEX_EN(val))
+ excluded |= SUPPORTED_100baseT_Half;
+ else
+ excluded |= SUPPORTED_100baseT_Full;
+ } else {
+ excluded |= SUPPORTED_100baseT_Full;
+ excluded |= SUPPORTED_100baseT_Half;
+ if (BAMBOO_FULL_DUPLEX_EN(val))
+ excluded |= SUPPORTED_10baseT_Half;
+ else
+ excluded |= SUPPORTED_10baseT_Full;
+ }
+ }
+
+ /* Set mac_addr, phy mode and unsupported phy features for each EMAC */
def = ocp_get_one_device(OCP_VENDOR_IBM, OCP_FUNC_EMAC, 0);
emacdata = def->additions;
memcpy(emacdata->mac_addr, __res.bi_enetaddr, 6);
emacdata->phy_mode = mode;
+ emacdata->phy_feat_exc = excluded;
def = ocp_get_one_device(OCP_VENDOR_IBM, OCP_FUNC_EMAC, 1);
emacdata = def->additions;
memcpy(emacdata->mac_addr, __res.bi_enet1addr, 6);
emacdata->phy_mode = mode;
+ emacdata->phy_feat_exc = excluded;
}
static int
diff -puN include/asm-ppc/ibm_ocp.h~ppc32-add-phy-excluded-features-to-ocp_func_emac_data include/asm-ppc/ibm_ocp.h
--- 25/include/asm-ppc/ibm_ocp.h~ppc32-add-phy-excluded-features-to-ocp_func_emac_data Wed Aug 17 14:17:15 2005
+++ 25-akpm/include/asm-ppc/ibm_ocp.h Wed Aug 17 14:17:15 2005
@@ -67,6 +67,7 @@ struct ocp_func_emac_data {
int phy_mode; /* PHY type or configurable mode */
u8 mac_addr[6]; /* EMAC mac address */
u32 phy_map; /* EMAC phy map */
+ u32 phy_feat_exc; /* Excluded PHY features */
};
/* Sysfs support */
_