From: Kumar Gala Support for the K2 board is no longer maintained and thus being removed Signed-off-by: Kumar Gala Signed-off-by: Andrew Morton --- dev/null | 1375 ------------------------------------------ arch/ppc/Kconfig | 9 arch/ppc/boot/simple/Makefile | 4 arch/ppc/platforms/Makefile | 1 arch/ppc/syslib/Makefile | 2 5 files changed, 1 insertion(+), 1390 deletions(-) diff -puN arch/ppc/boot/simple/Makefile~ppc32-remove-board-support-for-k2 arch/ppc/boot/simple/Makefile --- devel/arch/ppc/boot/simple/Makefile~ppc32-remove-board-support-for-k2 2005-07-30 00:43:58.000000000 -0700 +++ devel-akpm/arch/ppc/boot/simple/Makefile 2005-07-30 00:43:58.000000000 -0700 @@ -96,10 +96,6 @@ zimageinitrd-$(CONFIG_OCOTEA) := zImage zimageinitrd-$(CONFIG_GEMINI) := zImage.initrd-STRIPELF end-$(CONFIG_GEMINI) := gemini - extra.o-$(CONFIG_K2) := prepmap.o - end-$(CONFIG_K2) := k2 - cacheflag-$(CONFIG_K2) := -include $(clear_L2_L3) - extra.o-$(CONFIG_KATANA) := misc-katana.o end-$(CONFIG_KATANA) := katana cacheflag-$(CONFIG_KATANA) := -include $(clear_L2_L3) diff -L arch/ppc/configs/k2_defconfig -puN arch/ppc/configs/k2_defconfig~ppc32-remove-board-support-for-k2 /dev/null --- devel/arch/ppc/configs/k2_defconfig +++ /dev/null 2003-09-15 06:40:47.000000000 -0700 @@ -1,680 +0,0 @@ -# -# Automatically generated make config: don't edit -# -CONFIG_MMU=y -CONFIG_RWSEM_XCHGADD_ALGORITHM=y -CONFIG_HAVE_DEC_LOCK=y -CONFIG_PPC=y -CONFIG_PPC32=y -CONFIG_GENERIC_NVRAM=y - -# -# Code maturity level options -# -CONFIG_EXPERIMENTAL=y -CONFIG_CLEAN_COMPILE=y -CONFIG_STANDALONE=y -CONFIG_BROKEN_ON_SMP=y - -# -# General setup -# -CONFIG_SWAP=y -CONFIG_SYSVIPC=y -# CONFIG_POSIX_MQUEUE is not set -# CONFIG_BSD_PROCESS_ACCT is not set -CONFIG_SYSCTL=y -# CONFIG_AUDIT is not set -CONFIG_LOG_BUF_SHIFT=14 -# CONFIG_HOTPLUG is not set -# CONFIG_IKCONFIG is not set -CONFIG_EMBEDDED=y -CONFIG_KALLSYMS=y -CONFIG_FUTEX=y -CONFIG_EPOLL=y -CONFIG_IOSCHED_NOOP=y -CONFIG_IOSCHED_AS=y -CONFIG_IOSCHED_DEADLINE=y -CONFIG_IOSCHED_CFQ=y -# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set - -# -# Loadable module support -# -CONFIG_MODULES=y -CONFIG_MODULE_UNLOAD=y -# CONFIG_MODULE_FORCE_UNLOAD is not set -CONFIG_OBSOLETE_MODPARM=y -# CONFIG_MODVERSIONS is not set -CONFIG_KMOD=y - -# -# Processor -# -CONFIG_6xx=y -# CONFIG_40x is not set -# CONFIG_44x is not set -# CONFIG_POWER3 is not set -# CONFIG_POWER4 is not set -# CONFIG_8xx is not set -# CONFIG_ALTIVEC is not set -# CONFIG_TAU is not set -# CONFIG_CPU_FREQ is not set -CONFIG_PPC_STD_MMU=y - -# -# Platform options -# -# CONFIG_PPC_MULTIPLATFORM is not set -# CONFIG_APUS is not set -# CONFIG_WILLOW is not set -# CONFIG_PCORE is not set -# CONFIG_POWERPMC250 is not set -# CONFIG_EV64260 is not set -# CONFIG_SPRUCE is not set -# CONFIG_LOPEC is not set -# CONFIG_MCPN765 is not set -# CONFIG_MVME5100 is not set -# CONFIG_PPLUS is not set -# CONFIG_PRPMC750 is not set -# CONFIG_PRPMC800 is not set -# CONFIG_SANDPOINT is not set -# CONFIG_ADIR is not set -CONFIG_K2=y -# CONFIG_PAL4 is not set -# CONFIG_GEMINI is not set -# CONFIG_EST8260 is not set -# CONFIG_SBS8260 is not set -# CONFIG_RPX6 is not set -# CONFIG_TQM8260 is not set -CONFIG_PPC_GEN550=y -# CONFIG_CPC710_DATA_GATHERING is not set -# CONFIG_SMP is not set -# CONFIG_PREEMPT is not set -# CONFIG_HIGHMEM is not set -CONFIG_KERNEL_ELF=y -CONFIG_BINFMT_ELF=y -# CONFIG_BINFMT_MISC is not set -CONFIG_CMDLINE_BOOL=y -CONFIG_CMDLINE="ip=on" - -# -# Bus options -# -CONFIG_GENERIC_ISA_DMA=y -CONFIG_PCI=y -CONFIG_PCI_DOMAINS=y -# CONFIG_PCI_LEGACY_PROC is not set -# CONFIG_PCI_NAMES is not set - -# -# Advanced setup -# -# CONFIG_ADVANCED_OPTIONS is not set - -# -# Default settings for advanced configuration options are used -# -CONFIG_HIGHMEM_START=0xfe000000 -CONFIG_LOWMEM_SIZE=0x30000000 -CONFIG_KERNEL_START=0xc0000000 -CONFIG_TASK_SIZE=0x80000000 -CONFIG_BOOT_LOAD=0x00800000 - -# -# Device Drivers -# - -# -# Generic Driver Options -# - -# -# Memory Technology Devices (MTD) -# -# CONFIG_MTD is not set - -# -# Parallel port support -# -# CONFIG_PARPORT is not set - -# -# Plug and Play support -# - -# -# Block devices -# -# CONFIG_BLK_DEV_FD is not set -# CONFIG_BLK_CPQ_DA is not set -# CONFIG_BLK_CPQ_CISS_DA is not set -# CONFIG_BLK_DEV_DAC960 is not set -# CONFIG_BLK_DEV_UMEM is not set -CONFIG_BLK_DEV_LOOP=y -# CONFIG_BLK_DEV_CRYPTOLOOP is not set -# CONFIG_BLK_DEV_NBD is not set -# CONFIG_BLK_DEV_CARMEL is not set -CONFIG_BLK_DEV_RAM=y -CONFIG_BLK_DEV_RAM_SIZE=4096 -CONFIG_BLK_DEV_INITRD=y -# CONFIG_LBD is not set - -# -# ATA/ATAPI/MFM/RLL support -# -CONFIG_IDE=y -CONFIG_BLK_DEV_IDE=y - -# -# Please see Documentation/ide.txt for help/info on IDE drives -# -CONFIG_BLK_DEV_IDEDISK=y -# CONFIG_IDEDISK_MULTI_MODE is not set -# CONFIG_IDEDISK_STROKE is not set -# CONFIG_BLK_DEV_IDECD is not set -# CONFIG_BLK_DEV_IDETAPE is not set -# CONFIG_BLK_DEV_IDEFLOPPY is not set -# CONFIG_IDE_TASK_IOCTL is not set -# CONFIG_IDE_TASKFILE_IO is not set - -# -# IDE chipset support/bugfixes -# -# CONFIG_IDE_GENERIC is not set -CONFIG_BLK_DEV_IDEPCI=y -# CONFIG_IDEPCI_SHARE_IRQ is not set -# CONFIG_BLK_DEV_OFFBOARD is not set -# CONFIG_BLK_DEV_GENERIC is not set -# CONFIG_BLK_DEV_OPTI621 is not set -# CONFIG_BLK_DEV_SL82C105 is not set -CONFIG_BLK_DEV_IDEDMA_PCI=y -# CONFIG_BLK_DEV_IDEDMA_FORCED is not set -# CONFIG_IDEDMA_PCI_AUTO is not set -CONFIG_BLK_DEV_ADMA=y -# CONFIG_BLK_DEV_AEC62XX is not set -CONFIG_BLK_DEV_ALI15X3=y -# CONFIG_WDC_ALI15X3 is not set -# CONFIG_BLK_DEV_AMD74XX is not set -# CONFIG_BLK_DEV_CMD64X is not set -# CONFIG_BLK_DEV_TRIFLEX is not set -# CONFIG_BLK_DEV_CY82C693 is not set -# CONFIG_BLK_DEV_CS5520 is not set -# CONFIG_BLK_DEV_CS5530 is not set -# CONFIG_BLK_DEV_HPT34X is not set -# CONFIG_BLK_DEV_HPT366 is not set -# CONFIG_BLK_DEV_SC1200 is not set -# CONFIG_BLK_DEV_PIIX is not set -# CONFIG_BLK_DEV_NS87415 is not set -# CONFIG_BLK_DEV_PDC202XX_OLD is not set -# CONFIG_BLK_DEV_PDC202XX_NEW is not set -# CONFIG_BLK_DEV_SVWKS is not set -# CONFIG_BLK_DEV_SIIMAGE is not set -# CONFIG_BLK_DEV_SLC90E66 is not set -# CONFIG_BLK_DEV_TRM290 is not set -# CONFIG_BLK_DEV_VIA82CXXX is not set -CONFIG_BLK_DEV_IDEDMA=y -# CONFIG_IDEDMA_IVB is not set -# CONFIG_IDEDMA_AUTO is not set -# CONFIG_BLK_DEV_HD is not set - -# -# SCSI device support -# -# CONFIG_SCSI is not set - -# -# Multi-device support (RAID and LVM) -# -# CONFIG_MD is not set - -# -# Fusion MPT device support -# -# CONFIG_FUSION is not set - -# -# IEEE 1394 (FireWire) support -# -# CONFIG_IEEE1394 is not set - -# -# I2O device support -# -# CONFIG_I2O is not set - -# -# Macintosh device drivers -# - -# -# Networking support -# -CONFIG_NET=y - -# -# Networking options -# -CONFIG_PACKET=y -# CONFIG_PACKET_MMAP is not set -# CONFIG_NETLINK_DEV is not set -CONFIG_UNIX=y -# CONFIG_NET_KEY is not set -CONFIG_INET=y -# CONFIG_IP_MULTICAST is not set -# CONFIG_IP_ADVANCED_ROUTER is not set -CONFIG_IP_PNP=y -CONFIG_IP_PNP_DHCP=y -# CONFIG_IP_PNP_BOOTP is not set -# CONFIG_IP_PNP_RARP is not set -# CONFIG_NET_IPIP is not set -# CONFIG_NET_IPGRE is not set -# CONFIG_ARPD is not set -# CONFIG_SYN_COOKIES is not set -# CONFIG_INET_AH is not set -# CONFIG_INET_ESP is not set -# CONFIG_INET_IPCOMP is not set - -# -# IP: Virtual Server Configuration -# -# CONFIG_IP_VS is not set -# CONFIG_IPV6 is not set -CONFIG_NETFILTER=y -# CONFIG_NETFILTER_DEBUG is not set - -# -# IP: Netfilter Configuration -# -CONFIG_IP_NF_CONNTRACK=m -CONFIG_IP_NF_FTP=m -# CONFIG_IP_NF_IRC is not set -# CONFIG_IP_NF_TFTP is not set -# CONFIG_IP_NF_AMANDA is not set -# CONFIG_IP_NF_QUEUE is not set -CONFIG_IP_NF_IPTABLES=m -CONFIG_IP_NF_MATCH_LIMIT=m -# CONFIG_IP_NF_MATCH_IPRANGE is not set -CONFIG_IP_NF_MATCH_MAC=m -CONFIG_IP_NF_MATCH_PKTTYPE=m -CONFIG_IP_NF_MATCH_MARK=m -CONFIG_IP_NF_MATCH_MULTIPORT=m -CONFIG_IP_NF_MATCH_TOS=m -# CONFIG_IP_NF_MATCH_RECENT is not set -CONFIG_IP_NF_MATCH_ECN=m -CONFIG_IP_NF_MATCH_DSCP=m -CONFIG_IP_NF_MATCH_AH_ESP=m -# CONFIG_IP_NF_MATCH_LENGTH is not set -# CONFIG_IP_NF_MATCH_TTL is not set -CONFIG_IP_NF_MATCH_TCPMSS=m -CONFIG_IP_NF_MATCH_HELPER=m -CONFIG_IP_NF_MATCH_STATE=m -CONFIG_IP_NF_MATCH_CONNTRACK=m -CONFIG_IP_NF_MATCH_OWNER=m -CONFIG_IP_NF_FILTER=m -CONFIG_IP_NF_TARGET_REJECT=m -CONFIG_IP_NF_NAT=m -CONFIG_IP_NF_NAT_NEEDED=y -CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_REDIRECT=m -# CONFIG_IP_NF_TARGET_NETMAP is not set -# CONFIG_IP_NF_TARGET_SAME is not set -# CONFIG_IP_NF_NAT_SNMP_BASIC is not set -CONFIG_IP_NF_NAT_FTP=m -# CONFIG_IP_NF_MANGLE is not set -# CONFIG_IP_NF_TARGET_LOG is not set -CONFIG_IP_NF_TARGET_ULOG=m -CONFIG_IP_NF_TARGET_TCPMSS=m -CONFIG_IP_NF_ARPTABLES=m -CONFIG_IP_NF_ARPFILTER=m -# CONFIG_IP_NF_ARP_MANGLE is not set -CONFIG_IP_NF_COMPAT_IPCHAINS=m -# CONFIG_IP_NF_COMPAT_IPFWADM is not set -# CONFIG_IP_NF_RAW is not set - -# -# SCTP Configuration (EXPERIMENTAL) -# -# CONFIG_IP_SCTP is not set -# CONFIG_ATM is not set -# CONFIG_BRIDGE is not set -# CONFIG_VLAN_8021Q is not set -# CONFIG_DECNET is not set -# CONFIG_LLC2 is not set -# CONFIG_IPX is not set -# CONFIG_ATALK is not set -# CONFIG_X25 is not set -# CONFIG_LAPB is not set -# CONFIG_NET_DIVERT is not set -# CONFIG_ECONET is not set -# CONFIG_WAN_ROUTER is not set -# CONFIG_NET_HW_FLOWCONTROL is not set - -# -# QoS and/or fair queueing -# -# CONFIG_NET_SCHED is not set - -# -# Network testing -# -# CONFIG_NET_PKTGEN is not set -# CONFIG_NETPOLL is not set -# CONFIG_NET_POLL_CONTROLLER is not set -# CONFIG_HAMRADIO is not set -# CONFIG_IRDA is not set -# CONFIG_BT is not set -CONFIG_NETDEVICES=y -# CONFIG_DUMMY is not set -# CONFIG_BONDING is not set -# CONFIG_EQUALIZER is not set -# CONFIG_TUN is not set - -# -# ARCnet devices -# -# CONFIG_ARCNET is not set - -# -# Ethernet (10 or 100Mbit) -# -CONFIG_NET_ETHERNET=y -CONFIG_MII=y -# CONFIG_OAKNET is not set -# CONFIG_HAPPYMEAL is not set -# CONFIG_SUNGEM is not set -# CONFIG_NET_VENDOR_3COM is not set - -# -# Tulip family network device support -# -# CONFIG_NET_TULIP is not set -# CONFIG_HP100 is not set -CONFIG_NET_PCI=y -# CONFIG_PCNET32 is not set -# CONFIG_AMD8111_ETH is not set -# CONFIG_ADAPTEC_STARFIRE is not set -# CONFIG_B44 is not set -# CONFIG_FORCEDETH is not set -# CONFIG_DGRS is not set -CONFIG_EEPRO100=y -# CONFIG_EEPRO100_PIO is not set -# CONFIG_E100 is not set -# CONFIG_FEALNX is not set -# CONFIG_NATSEMI is not set -# CONFIG_NE2K_PCI is not set -# CONFIG_8139CP is not set -# CONFIG_8139TOO is not set -# CONFIG_SIS900 is not set -# CONFIG_EPIC100 is not set -# CONFIG_SUNDANCE is not set -# CONFIG_TLAN is not set -# CONFIG_VIA_RHINE is not set - -# -# Ethernet (1000 Mbit) -# -# CONFIG_ACENIC is not set -# CONFIG_DL2K is not set -# CONFIG_E1000 is not set -# CONFIG_NS83820 is not set -# CONFIG_HAMACHI is not set -# CONFIG_YELLOWFIN is not set -# CONFIG_R8169 is not set -# CONFIG_SK98LIN is not set -# CONFIG_TIGON3 is not set - -# -# Ethernet (10000 Mbit) -# -# CONFIG_IXGB is not set -# CONFIG_S2IO is not set - -# -# Token Ring devices -# -# CONFIG_TR is not set - -# -# Wireless LAN (non-hamradio) -# -# CONFIG_NET_RADIO is not set - -# -# Wan interfaces -# -# CONFIG_WAN is not set -# CONFIG_FDDI is not set -# CONFIG_HIPPI is not set -# CONFIG_PPP is not set -# CONFIG_SLIP is not set -# CONFIG_RCPCI is not set -# CONFIG_SHAPER is not set -# CONFIG_NETCONSOLE is not set - -# -# ISDN subsystem -# -# CONFIG_ISDN is not set - -# -# Telephony Support -# -# CONFIG_PHONE is not set - -# -# Input device support -# -# CONFIG_INPUT is not set - -# -# Userland interfaces -# - -# -# Input I/O drivers -# -# CONFIG_GAMEPORT is not set -CONFIG_SOUND_GAMEPORT=y -# CONFIG_SERIO is not set -# CONFIG_SERIO_I8042 is not set - -# -# Input Device Drivers -# - -# -# Character devices -# -# CONFIG_VT is not set -# CONFIG_SERIAL_NONSTANDARD is not set - -# -# Serial drivers -# -CONFIG_SERIAL_8250=y -CONFIG_SERIAL_8250_CONSOLE=y -CONFIG_SERIAL_8250_NR_UARTS=2 -# CONFIG_SERIAL_8250_EXTENDED is not set - -# -# Non-8250 serial port support -# -CONFIG_SERIAL_CORE=y -CONFIG_SERIAL_CORE_CONSOLE=y -CONFIG_UNIX98_PTYS=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -# CONFIG_QIC02_TAPE is not set - -# -# IPMI -# -# CONFIG_IPMI_HANDLER is not set - -# -# Watchdog Cards -# -# CONFIG_WATCHDOG is not set -# CONFIG_NVRAM is not set -CONFIG_GEN_RTC=y -# CONFIG_GEN_RTC_X is not set -# CONFIG_DTLK is not set -# CONFIG_R3964 is not set -# CONFIG_APPLICOM is not set - -# -# Ftape, the floppy tape device driver -# -# CONFIG_FTAPE is not set -# CONFIG_AGP is not set -# CONFIG_DRM is not set -# CONFIG_RAW_DRIVER is not set - -# -# I2C support -# -# CONFIG_I2C is not set - -# -# Misc devices -# - -# -# Multimedia devices -# -# CONFIG_VIDEO_DEV is not set - -# -# Digital Video Broadcasting Devices -# -# CONFIG_DVB is not set - -# -# Graphics support -# -# CONFIG_FB is not set - -# -# Sound -# -# CONFIG_SOUND is not set - -# -# USB support -# -# CONFIG_USB is not set - -# -# USB Gadget Support -# -# CONFIG_USB_GADGET is not set - -# -# File systems -# -CONFIG_EXT2_FS=y -# CONFIG_EXT2_FS_XATTR is not set -# CONFIG_EXT3_FS is not set -# CONFIG_JBD is not set -# CONFIG_REISERFS_FS is not set -# CONFIG_JFS_FS is not set -# CONFIG_XFS_FS is not set -# CONFIG_MINIX_FS is not set -# CONFIG_ROMFS_FS is not set -# CONFIG_QUOTA is not set -# CONFIG_AUTOFS_FS is not set -# CONFIG_AUTOFS4_FS is not set - -# -# CD-ROM/DVD Filesystems -# -# CONFIG_ISO9660_FS is not set -# CONFIG_UDF_FS is not set - -# -# DOS/FAT/NT Filesystems -# -# CONFIG_FAT_FS is not set -# CONFIG_NTFS_FS is not set - -# -# Pseudo filesystems -# -CONFIG_PROC_FS=y -CONFIG_PROC_KCORE=y -CONFIG_SYSFS=y -# CONFIG_DEVFS_FS is not set -# CONFIG_DEVPTS_FS_XATTR is not set -CONFIG_TMPFS=y -# CONFIG_HUGETLB_PAGE is not set -CONFIG_RAMFS=y - -# -# Miscellaneous filesystems -# -# CONFIG_ADFS_FS is not set -# CONFIG_AFFS_FS is not set -# CONFIG_HFS_FS is not set -# CONFIG_HFSPLUS_FS is not set -# CONFIG_BEFS_FS is not set -# CONFIG_BFS_FS is not set -# CONFIG_EFS_FS is not set -# CONFIG_CRAMFS is not set -# CONFIG_VXFS_FS is not set -# CONFIG_HPFS_FS is not set -# CONFIG_QNX4FS_FS is not set -# CONFIG_SYSV_FS is not set -# CONFIG_UFS_FS is not set - -# -# Network File Systems -# -CONFIG_NFS_FS=y -# CONFIG_NFS_V3 is not set -# CONFIG_NFS_V4 is not set -# CONFIG_NFS_DIRECTIO is not set -# CONFIG_NFSD is not set -CONFIG_ROOT_NFS=y -CONFIG_LOCKD=y -# CONFIG_EXPORTFS is not set -CONFIG_SUNRPC=y -# CONFIG_RPCSEC_GSS_KRB5 is not set -# CONFIG_SMB_FS is not set -# CONFIG_CIFS is not set -# CONFIG_NCP_FS is not set -# CONFIG_CODA_FS is not set -# CONFIG_INTERMEZZO_FS is not set -# CONFIG_AFS_FS is not set - -# -# Partition Types -# -# CONFIG_PARTITION_ADVANCED is not set -CONFIG_MSDOS_PARTITION=y - -# -# Native Language Support -# -# CONFIG_NLS is not set - -# -# Library routines -# -# CONFIG_CRC32 is not set - -# -# Kernel hacking -# -# CONFIG_DEBUG_KERNEL is not set -# CONFIG_SERIAL_TEXT_DEBUG is not set - -# -# Security options -# -# CONFIG_SECURITY is not set - -# -# Cryptographic options -# -# CONFIG_CRYPTO is not set diff -puN arch/ppc/Kconfig~ppc32-remove-board-support-for-k2 arch/ppc/Kconfig --- devel/arch/ppc/Kconfig~ppc32-remove-board-support-for-k2 2005-07-30 00:43:58.000000000 -0700 +++ devel-akpm/arch/ppc/Kconfig 2005-07-30 00:43:58.000000000 -0700 @@ -637,9 +637,6 @@ config SANDPOINT config RADSTONE_PPC7D bool "Radstone Technology PPC7D board" -config K2 - bool "SBS-K2" - config PAL4 bool "SBS-Palomar4" @@ -794,7 +791,7 @@ config PPC_OF config PPC_GEN550 bool depends on SANDPOINT || MCPN765 || SPRUCE || PPLUS || PCORE || \ - PRPMC750 || K2 || PRPMC800 || LOPEC || \ + PRPMC750 || PRPMC800 || LOPEC || \ (EV64260 && !SERIAL_MPSC) || CHESTNUT || RADSTONE_PPC7D || \ 83xx default y @@ -883,10 +880,6 @@ config SANDPOINT_ENABLE_UART1 If this option is enabled then the MPC824x processor will run in DUART mode instead of UART mode. -config CPC710_DATA_GATHERING - bool "Enable CPC710 data gathering" - depends on K2 - config HARRIER_STORE_GATHERING bool "Enable Harrier store gathering" depends on HARRIER diff -L arch/ppc/platforms/k2.c -puN arch/ppc/platforms/k2.c~ppc32-remove-board-support-for-k2 /dev/null --- devel/arch/ppc/platforms/k2.c +++ /dev/null 2003-09-15 06:40:47.000000000 -0700 @@ -1,613 +0,0 @@ -/* - * arch/ppc/platforms/k2.c - * - * Board setup routines for SBS K2 - * - * Author: Matt Porter - * - * Updated by: Randy Vinson -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -#include -#include "k2.h" - -extern unsigned long loops_per_jiffy; -extern void gen550_progress(char *, unsigned short); - -static unsigned int cpu_7xx[16] = { - 0, 15, 14, 0, 0, 13, 5, 9, 6, 11, 8, 10, 16, 12, 7, 0 -}; -static unsigned int cpu_6xx[16] = { - 0, 0, 14, 0, 0, 13, 5, 9, 6, 11, 8, 10, 0, 12, 7, 0 -}; - -static inline int __init -k2_map_irq(struct pci_dev *dev, unsigned char idsel, unsigned char pin) -{ - struct pci_controller *hose = pci_bus_to_hose(dev->bus->number); - /* - * Check our hose index. If we are zero then we are on the - * local PCI hose, otherwise we are on the cPCI hose. - */ - if (!hose->index) { - static char pci_irq_table[][4] = - /* - * PCI IDSEL/INTPIN->INTLINE - * A B C D - */ - { - {1, 0, 0, 0}, /* Ethernet */ - {5, 5, 5, 5}, /* PMC Site 1 */ - {6, 6, 6, 6}, /* PMC Site 2 */ - {0, 0, 0, 0}, /* unused */ - {0, 0, 0, 0}, /* unused */ - {0, 0, 0, 0}, /* PCI-ISA Bridge */ - {0, 0, 0, 0}, /* unused */ - {0, 0, 0, 0}, /* unused */ - {0, 0, 0, 0}, /* unused */ - {0, 0, 0, 0}, /* unused */ - {0, 0, 0, 0}, /* unused */ - {0, 0, 0, 0}, /* unused */ - {0, 0, 0, 0}, /* unused */ - {0, 0, 0, 0}, /* unused */ - {15, 0, 0, 0}, /* M5229 IDE */ - }; - const long min_idsel = 3, max_idsel = 17, irqs_per_slot = 4; - return PCI_IRQ_TABLE_LOOKUP; - } else { - static char pci_irq_table[][4] = - /* - * PCI IDSEL/INTPIN->INTLINE - * A B C D - */ - { - {10, 11, 12, 9}, /* cPCI slot 8 */ - {11, 12, 9, 10}, /* cPCI slot 7 */ - {12, 9, 10, 11}, /* cPCI slot 6 */ - {9, 10, 11, 12}, /* cPCI slot 5 */ - {10, 11, 12, 9}, /* cPCI slot 4 */ - {11, 12, 9, 10}, /* cPCI slot 3 */ - {12, 9, 10, 11}, /* cPCI slot 2 */ - }; - const long min_idsel = 15, max_idsel = 21, irqs_per_slot = 4; - return PCI_IRQ_TABLE_LOOKUP; - } -} - -void k2_pcibios_fixup(void) -{ -#if defined(CONFIG_BLK_DEV_IDE) || defined(CONFIG_BLK_DEV_IDE_MODULE) - struct pci_dev *ide_dev; - - /* - * Enable DMA support on hdc - */ - ide_dev = pci_get_device(PCI_VENDOR_ID_AL, - PCI_DEVICE_ID_AL_M5229, NULL); - - if (ide_dev) { - - unsigned long ide_dma_base; - - ide_dma_base = pci_resource_start(ide_dev, 4); - outb(0x00, ide_dma_base + 0x2); - outb(0x20, ide_dma_base + 0xa); - pci_dev_put(ide_dev); - } -#endif -} - -void k2_pcibios_fixup_resources(struct pci_dev *dev) -{ - int i; - - if ((dev->vendor == PCI_VENDOR_ID_IBM) && - (dev->device == PCI_DEVICE_ID_IBM_CPC710_PCI64)) { - pr_debug("Fixup CPC710 resources\n"); - for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) { - dev->resource[i].start = 0; - dev->resource[i].end = 0; - } - } -} - -void k2_setup_hoses(void) -{ - struct pci_controller *hose_a, *hose_b; - - /* - * Reconfigure CPC710 memory map so - * we have some more PCI memory space. - */ - - /* Set FPHB mode */ - __raw_writel(0x808000e0, PGCHP); /* Set FPHB mode */ - - /* PCI32 mappings */ - __raw_writel(0x00000000, K2_PCI32_BAR + PIBAR); /* PCI I/O base */ - __raw_writel(0x00000000, K2_PCI32_BAR + PMBAR); /* PCI Mem base */ - __raw_writel(0xf0000000, K2_PCI32_BAR + MSIZE); /* 256MB */ - __raw_writel(0xfff00000, K2_PCI32_BAR + IOSIZE); /* 1MB */ - __raw_writel(0xc0000000, K2_PCI32_BAR + SMBAR); /* Base@0xc0000000 */ - __raw_writel(0x80000000, K2_PCI32_BAR + SIBAR); /* Base@0x80000000 */ - __raw_writel(0x000000c0, K2_PCI32_BAR + PSSIZE); /* 1GB space */ - __raw_writel(0x000000c0, K2_PCI32_BAR + PPSIZE); /* 1GB space */ - __raw_writel(0x00000000, K2_PCI32_BAR + BARPS); /* Base@0x00000000 */ - __raw_writel(0x00000000, K2_PCI32_BAR + BARPP); /* Base@0x00000000 */ - __raw_writel(0x00000080, K2_PCI32_BAR + PSBAR); /* Base@0x80 */ - __raw_writel(0x00000000, K2_PCI32_BAR + PPBAR); - - __raw_writel(0xc0000000, K2_PCI32_BAR + BPMDLK); - __raw_writel(0xd0000000, K2_PCI32_BAR + TPMDLK); - __raw_writel(0x80000000, K2_PCI32_BAR + BIODLK); - __raw_writel(0x80100000, K2_PCI32_BAR + TIODLK); - __raw_writel(0xe0008000, K2_PCI32_BAR + DLKCTRL); - __raw_writel(0xffffffff, K2_PCI32_BAR + DLKDEV); - - /* PCI64 mappings */ - __raw_writel(0x00100000, K2_PCI64_BAR + PIBAR); /* PCI I/O base */ - __raw_writel(0x10000000, K2_PCI64_BAR + PMBAR); /* PCI Mem base */ - __raw_writel(0xf0000000, K2_PCI64_BAR + MSIZE); /* 256MB */ - __raw_writel(0xfff00000, K2_PCI64_BAR + IOSIZE); /* 1MB */ - __raw_writel(0xd0000000, K2_PCI64_BAR + SMBAR); /* Base@0xd0000000 */ - __raw_writel(0x80100000, K2_PCI64_BAR + SIBAR); /* Base@0x80100000 */ - __raw_writel(0x000000c0, K2_PCI64_BAR + PSSIZE); /* 1GB space */ - __raw_writel(0x000000c0, K2_PCI64_BAR + PPSIZE); /* 1GB space */ - __raw_writel(0x00000000, K2_PCI64_BAR + BARPS); /* Base@0x00000000 */ - __raw_writel(0x00000000, K2_PCI64_BAR + BARPP); /* Base@0x00000000 */ - - /* Setup PCI32 hose */ - hose_a = pcibios_alloc_controller(); - if (!hose_a) - return; - - hose_a->first_busno = 0; - hose_a->last_busno = 0xff; - hose_a->pci_mem_offset = K2_PCI32_MEM_BASE; - - pci_init_resource(&hose_a->io_resource, - K2_PCI32_LOWER_IO, - K2_PCI32_UPPER_IO, - IORESOURCE_IO, "PCI32 host bridge"); - - pci_init_resource(&hose_a->mem_resources[0], - K2_PCI32_LOWER_MEM + K2_PCI32_MEM_BASE, - K2_PCI32_UPPER_MEM + K2_PCI32_MEM_BASE, - IORESOURCE_MEM, "PCI32 host bridge"); - - hose_a->io_space.start = K2_PCI32_LOWER_IO; - hose_a->io_space.end = K2_PCI32_UPPER_IO; - hose_a->mem_space.start = K2_PCI32_LOWER_MEM; - hose_a->mem_space.end = K2_PCI32_UPPER_MEM; - hose_a->io_base_virt = (void *)K2_ISA_IO_BASE; - - setup_indirect_pci(hose_a, K2_PCI32_CONFIG_ADDR, K2_PCI32_CONFIG_DATA); - - /* Initialize PCI32 bus registers */ - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(0, 0), - CPC710_BUS_NUMBER, hose_a->first_busno); - - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(0, 0), - CPC710_SUB_BUS_NUMBER, hose_a->last_busno); - - /* Enable PCI interrupt polling */ - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(8, 0), 0x45, 0x80); - - /* Route polled PCI interrupts */ - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(8, 0), 0x48, 0x58); - - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(8, 0), 0x49, 0x07); - - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(8, 0), 0x4a, 0x31); - - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(8, 0), 0x4b, 0xb9); - - /* route secondary IDE channel interrupt to IRQ 15 */ - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(8, 0), 0x75, 0x0f); - - /* enable IDE controller IDSEL */ - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(8, 0), 0x58, 0x48); - - /* Enable IDE function */ - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(17, 0), 0x50, 0x03); - - /* Set M5229 IDE controller to native mode */ - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(17, 0), PCI_CLASS_PROG, 0xdf); - - hose_a->last_busno = pciauto_bus_scan(hose_a, hose_a->first_busno); - - /* Write out correct max subordinate bus number for hose A */ - early_write_config_byte(hose_a, - hose_a->first_busno, - PCI_DEVFN(0, 0), - CPC710_SUB_BUS_NUMBER, hose_a->last_busno); - - /* Only setup PCI64 hose if we are in the system slot */ - if (!(readb(K2_MISC_REG) & K2_SYS_SLOT_MASK)) { - /* Setup PCI64 hose */ - hose_b = pcibios_alloc_controller(); - if (!hose_b) - return; - - hose_b->first_busno = hose_a->last_busno + 1; - hose_b->last_busno = 0xff; - - /* Reminder: quit changing the following, it is correct. */ - hose_b->pci_mem_offset = K2_PCI32_MEM_BASE; - - pci_init_resource(&hose_b->io_resource, - K2_PCI64_LOWER_IO, - K2_PCI64_UPPER_IO, - IORESOURCE_IO, "PCI64 host bridge"); - - pci_init_resource(&hose_b->mem_resources[0], - K2_PCI64_LOWER_MEM + K2_PCI32_MEM_BASE, - K2_PCI64_UPPER_MEM + K2_PCI32_MEM_BASE, - IORESOURCE_MEM, "PCI64 host bridge"); - - hose_b->io_space.start = K2_PCI64_LOWER_IO; - hose_b->io_space.end = K2_PCI64_UPPER_IO; - hose_b->mem_space.start = K2_PCI64_LOWER_MEM; - hose_b->mem_space.end = K2_PCI64_UPPER_MEM; - hose_b->io_base_virt = (void *)K2_ISA_IO_BASE; - - setup_indirect_pci(hose_b, - K2_PCI64_CONFIG_ADDR, K2_PCI64_CONFIG_DATA); - - /* Initialize PCI64 bus registers */ - early_write_config_byte(hose_b, - 0, - PCI_DEVFN(0, 0), - CPC710_SUB_BUS_NUMBER, 0xff); - - early_write_config_byte(hose_b, - 0, - PCI_DEVFN(0, 0), - CPC710_BUS_NUMBER, hose_b->first_busno); - - hose_b->last_busno = pciauto_bus_scan(hose_b, - hose_b->first_busno); - - /* Write out correct max subordinate bus number for hose B */ - early_write_config_byte(hose_b, - hose_b->first_busno, - PCI_DEVFN(0, 0), - CPC710_SUB_BUS_NUMBER, - hose_b->last_busno); - - /* Configure PCI64 PSBAR */ - early_write_config_dword(hose_b, - hose_b->first_busno, - PCI_DEVFN(0, 0), - PCI_BASE_ADDRESS_0, - K2_PCI64_SYS_MEM_BASE); - } - - /* Configure i8259 level/edge settings */ - outb(0x62, 0x4d0); - outb(0xde, 0x4d1); - -#ifdef CONFIG_CPC710_DATA_GATHERING - { - unsigned int tmp; - tmp = __raw_readl(ABCNTL); - /* Enable data gathering on both PCI interfaces */ - __raw_writel(tmp | 0x05000000, ABCNTL); - } -#endif - - ppc_md.pcibios_fixup = k2_pcibios_fixup; - ppc_md.pcibios_fixup_resources = k2_pcibios_fixup_resources; - ppc_md.pci_swizzle = common_swizzle; - ppc_md.pci_map_irq = k2_map_irq; -} - -static int k2_get_bus_speed(void) -{ - int bus_speed; - unsigned char board_id; - - board_id = *(unsigned char *)K2_BOARD_ID_REG; - - switch (K2_BUS_SPD(board_id)) { - - case 0: - default: - bus_speed = 100000000; - break; - - case 1: - bus_speed = 83333333; - break; - - case 2: - bus_speed = 75000000; - break; - - case 3: - bus_speed = 66666666; - break; - } - return bus_speed; -} - -static int k2_get_cpu_speed(void) -{ - unsigned long hid1; - int cpu_speed; - - hid1 = mfspr(SPRN_HID1) >> 28; - - if ((mfspr(SPRN_PVR) >> 16) == 8) - hid1 = cpu_7xx[hid1]; - else - hid1 = cpu_6xx[hid1]; - - cpu_speed = k2_get_bus_speed() * hid1 / 2; - return cpu_speed; -} - -static void __init k2_calibrate_decr(void) -{ - int freq, divisor = 4; - - /* determine processor bus speed */ - freq = k2_get_bus_speed(); - tb_ticks_per_jiffy = freq / HZ / divisor; - tb_to_us = mulhwu_scale_factor(freq / divisor, 1000000); -} - -static int k2_show_cpuinfo(struct seq_file *m) -{ - unsigned char k2_geo_bits, k2_system_slot; - - seq_printf(m, "vendor\t\t: SBS\n"); - seq_printf(m, "machine\t\t: K2\n"); - seq_printf(m, "cpu speed\t: %dMhz\n", k2_get_cpu_speed() / 1000000); - seq_printf(m, "bus speed\t: %dMhz\n", k2_get_bus_speed() / 1000000); - seq_printf(m, "memory type\t: SDRAM\n"); - - k2_geo_bits = readb(K2_MSIZ_GEO_REG) & K2_GEO_ADR_MASK; - k2_system_slot = !(readb(K2_MISC_REG) & K2_SYS_SLOT_MASK); - seq_printf(m, "backplane\t: %s slot board", - k2_system_slot ? "System" : "Non system"); - seq_printf(m, "with geographical address %x\n", k2_geo_bits); - - return 0; -} - -TODC_ALLOC(); - -static void __init k2_setup_arch(void) -{ - unsigned int cpu; - - /* Setup TODC access */ - TODC_INIT(TODC_TYPE_MK48T37, 0, 0, - ioremap(K2_RTC_BASE_ADDRESS, K2_RTC_SIZE), 8); - - /* init to some ~sane value until calibrate_delay() runs */ - loops_per_jiffy = 50000000 / HZ; - - /* make FLASH transactions higher priority than PCI to avoid deadlock */ - __raw_writel(__raw_readl(SIOC1) | 0x80000000, SIOC1); - - /* Set hardware to access FLASH page 2 */ - __raw_writel(1 << 29, GPOUT); - - /* Setup PCI host bridges */ - k2_setup_hoses(); - -#ifdef CONFIG_BLK_DEV_INITRD - if (initrd_start) - ROOT_DEV = Root_RAM0; - else -#endif -#ifdef CONFIG_ROOT_NFS - ROOT_DEV = Root_NFS; -#else - ROOT_DEV = Root_HDC1; -#endif - - /* Identify the system */ - printk(KERN_INFO "System Identification: SBS K2 - PowerPC 750 @ " - "%d Mhz\n", k2_get_cpu_speed() / 1000000); - printk(KERN_INFO "Port by MontaVista Software, Inc. " - "(source@mvista.com)\n"); - - /* Identify the CPU manufacturer */ - cpu = PVR_REV(mfspr(SPRN_PVR)); - printk(KERN_INFO "CPU manufacturer: %s [rev=%04x]\n", - (cpu & (1 << 15)) ? "IBM" : "Motorola", cpu); -} - -static void k2_restart(char *cmd) -{ - local_irq_disable(); - - /* Flip FLASH back to page 1 to access firmware image */ - __raw_writel(0, GPOUT); - - /* SRR0 has system reset vector, SRR1 has default MSR value */ - /* rfi restores MSR from SRR1 and sets the PC to the SRR0 value */ - mtspr(SPRN_SRR0, 0xfff00100); - mtspr(SPRN_SRR1, 0); - __asm__ __volatile__("rfi\n\t"); - - /* not reached */ - for (;;) ; -} - -static void k2_power_off(void) -{ - for (;;) ; -} - -static void k2_halt(void) -{ - k2_restart(NULL); -} - -/* - * Set BAT 3 to map PCI32 I/O space. - */ -static __inline__ void k2_set_bat(void) -{ - /* wait for all outstanding memory accesses to complete */ - mb(); - - /* setup DBATs */ - mtspr(SPRN_DBAT2U, 0x80001ffe); - mtspr(SPRN_DBAT2L, 0x8000002a); - mtspr(SPRN_DBAT3U, 0xf0001ffe); - mtspr(SPRN_DBAT3L, 0xf000002a); - - /* wait for updates */ - mb(); -} - -static unsigned long __init k2_find_end_of_memory(void) -{ - unsigned long total; - unsigned char msize = 7; /* Default to 128MB */ - - msize = K2_MEM_SIZE(readb(K2_MSIZ_GEO_REG)); - - switch (msize) { - case 2: - /* - * This will break without a lowered - * KERNELBASE or CONFIG_HIGHMEM on. - * It seems non 1GB builds exist yet, - * though. - */ - total = K2_MEM_SIZE_1GB; - break; - case 3: - case 4: - total = K2_MEM_SIZE_512MB; - break; - case 5: - case 6: - total = K2_MEM_SIZE_256MB; - break; - case 7: - total = K2_MEM_SIZE_128MB; - break; - default: - printk - ("K2: Invalid memory size detected, defaulting to 128MB\n"); - total = K2_MEM_SIZE_128MB; - break; - } - return total; -} - -static void __init k2_map_io(void) -{ - io_block_mapping(K2_PCI32_IO_BASE, - K2_PCI32_IO_BASE, 0x00200000, _PAGE_IO); - io_block_mapping(0xff000000, 0xff000000, 0x01000000, _PAGE_IO); -} - -static void __init k2_init_irq(void) -{ - int i; - - for (i = 0; i < 16; i++) - irq_desc[i].handler = &i8259_pic; - - i8259_init(0); -} - -void __init platform_init(unsigned long r3, unsigned long r4, - unsigned long r5, unsigned long r6, unsigned long r7) -{ - parse_bootinfo((struct bi_record *)(r3 + KERNELBASE)); - - k2_set_bat(); - - isa_io_base = K2_ISA_IO_BASE; - isa_mem_base = K2_ISA_MEM_BASE; - pci_dram_offset = K2_PCI32_SYS_MEM_BASE; - - ppc_md.setup_arch = k2_setup_arch; - ppc_md.show_cpuinfo = k2_show_cpuinfo; - ppc_md.init_IRQ = k2_init_irq; - ppc_md.get_irq = i8259_irq; - - ppc_md.find_end_of_memory = k2_find_end_of_memory; - ppc_md.setup_io_mappings = k2_map_io; - - ppc_md.restart = k2_restart; - ppc_md.power_off = k2_power_off; - ppc_md.halt = k2_halt; - - ppc_md.time_init = todc_time_init; - ppc_md.set_rtc_time = todc_set_rtc_time; - ppc_md.get_rtc_time = todc_get_rtc_time; - ppc_md.calibrate_decr = k2_calibrate_decr; - - ppc_md.nvram_read_val = todc_direct_read_val; - ppc_md.nvram_write_val = todc_direct_write_val; - -#ifdef CONFIG_SERIAL_TEXT_DEBUG - ppc_md.progress = gen550_progress; -#endif -} diff -L arch/ppc/platforms/k2.h -puN arch/ppc/platforms/k2.h~ppc32-remove-board-support-for-k2 /dev/null --- devel/arch/ppc/platforms/k2.h +++ /dev/null 2003-09-15 06:40:47.000000000 -0700 @@ -1,82 +0,0 @@ -/* - * arch/ppc/platforms/k2.h - * - * Definitions for SBS K2 board support - * - * Author: Matt Porter - * - * 2001 (c) MontaVista, Software, Inc. This file is licensed under - * the terms of the GNU General Public License version 2. This program - * is licensed "as is" without any warranty of any kind, whether express - * or implied. - */ - -#ifndef __PPC_PLATFORMS_K2_H -#define __PPC_PLATFORMS_K2_H - -/* - * SBS K2 definitions - */ - -#define K2_PCI64_BAR 0xff400000 -#define K2_PCI32_BAR 0xff500000 - -#define K2_PCI64_CONFIG_ADDR (K2_PCI64_BAR + 0x000f8000) -#define K2_PCI64_CONFIG_DATA (K2_PCI64_BAR + 0x000f8010) - -#define K2_PCI32_CONFIG_ADDR (K2_PCI32_BAR + 0x000f8000) -#define K2_PCI32_CONFIG_DATA (K2_PCI32_BAR + 0x000f8010) - -#define K2_PCI64_MEM_BASE 0xd0000000 -#define K2_PCI64_IO_BASE 0x80100000 - -#define K2_PCI32_MEM_BASE 0xc0000000 -#define K2_PCI32_IO_BASE 0x80000000 - -#define K2_PCI32_SYS_MEM_BASE 0x80000000 -#define K2_PCI64_SYS_MEM_BASE K2_PCI32_SYS_MEM_BASE - -#define K2_PCI32_LOWER_MEM 0x00000000 -#define K2_PCI32_UPPER_MEM 0x0fffffff -#define K2_PCI32_LOWER_IO 0x00000000 -#define K2_PCI32_UPPER_IO 0x000fffff - -#define K2_PCI64_LOWER_MEM 0x10000000 -#define K2_PCI64_UPPER_MEM 0x1fffffff -#define K2_PCI64_LOWER_IO 0x00100000 -#define K2_PCI64_UPPER_IO 0x001fffff - -#define K2_ISA_IO_BASE K2_PCI32_IO_BASE -#define K2_ISA_MEM_BASE K2_PCI32_MEM_BASE - -#define K2_BOARD_ID_REG (K2_ISA_IO_BASE + 0x800) -#define K2_MISC_REG (K2_ISA_IO_BASE + 0x804) -#define K2_MSIZ_GEO_REG (K2_ISA_IO_BASE + 0x808) -#define K2_HOT_SWAP_REG (K2_ISA_IO_BASE + 0x80c) -#define K2_PLD2_REG (K2_ISA_IO_BASE + 0x80e) -#define K2_PLD3_REG (K2_ISA_IO_BASE + 0x80f) - -#define K2_BUS_SPD(board_id) (board_id >> 2) & 3 - -#define K2_RTC_BASE_OFFSET 0x90000 -#define K2_RTC_BASE_ADDRESS (K2_PCI32_MEM_BASE + K2_RTC_BASE_OFFSET) -#define K2_RTC_SIZE 0x8000 - -#define K2_MEM_SIZE_MASK 0xe0 -#define K2_MEM_SIZE(size_reg) (size_reg & K2_MEM_SIZE_MASK) >> 5 -#define K2_MEM_SIZE_1GB 0x40000000 -#define K2_MEM_SIZE_512MB 0x20000000 -#define K2_MEM_SIZE_256MB 0x10000000 -#define K2_MEM_SIZE_128MB 0x08000000 - -#define K2_L2CACHE_MASK 0x03 /* Mask for 2 L2 Cache bits */ -#define K2_L2CACHE_512KB 0x00 /* 512KB */ -#define K2_L2CACHE_256KB 0x01 /* 256KB */ -#define K2_L2CACHE_1MB 0x02 /* 1MB */ -#define K2_L2CACHE_NONE 0x03 /* None */ - -#define K2_GEO_ADR_MASK 0x1f - -#define K2_SYS_SLOT_MASK 0x08 - -#endif /* __PPC_PLATFORMS_K2_H */ diff -puN arch/ppc/platforms/Makefile~ppc32-remove-board-support-for-k2 arch/ppc/platforms/Makefile --- devel/arch/ppc/platforms/Makefile~ppc32-remove-board-support-for-k2 2005-07-30 00:43:58.000000000 -0700 +++ devel-akpm/arch/ppc/platforms/Makefile 2005-07-30 00:43:58.000000000 -0700 @@ -27,7 +27,6 @@ obj-$(CONFIG_CPCI690) += cpci690.o obj-$(CONFIG_EV64260) += ev64260.o obj-$(CONFIG_CHESTNUT) += chestnut.o obj-$(CONFIG_GEMINI) += gemini_pci.o gemini_setup.o gemini_prom.o -obj-$(CONFIG_K2) += k2.o obj-$(CONFIG_LOPEC) += lopec.o obj-$(CONFIG_KATANA) += katana.o obj-$(CONFIG_HDPU) += hdpu.o diff -puN arch/ppc/syslib/Makefile~ppc32-remove-board-support-for-k2 arch/ppc/syslib/Makefile --- devel/arch/ppc/syslib/Makefile~ppc32-remove-board-support-for-k2 2005-07-30 00:43:58.000000000 -0700 +++ devel-akpm/arch/ppc/syslib/Makefile 2005-07-30 00:43:58.000000000 -0700 @@ -50,8 +50,6 @@ obj-$(CONFIG_EV64260) += todc_time.o pc obj-$(CONFIG_CHESTNUT) += mv64360_pic.o pci_auto.o obj-$(CONFIG_GEMINI) += open_pic.o indirect_pci.o obj-$(CONFIG_GT64260) += gt64260_pic.o -obj-$(CONFIG_K2) += i8259.o indirect_pci.o todc_time.o \ - pci_auto.o obj-$(CONFIG_LOPEC) += i8259.o pci_auto.o todc_time.o obj-$(CONFIG_HDPU) += pci_auto.o obj-$(CONFIG_LUAN) += indirect_pci.o pci_auto.o todc_time.o _