GIT 559fb51ba7e66fe298b8355fabde1275b7def35f master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6.git#chelsio --- Index: Documentation/networking/cxgb.txt =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/Documentation/networking/cxgb.txt (mode:100644) @@ -0,0 +1,352 @@ + Chelsio N210 10Gb Ethernet Network Controller + + Driver Release Notes for Linux + + Version 2.1.1 + + June 20, 2005 + +CONTENTS +======== + INTRODUCTION + FEATURES + PERFORMANCE + DRIVER MESSAGES + KNOWN ISSUES + SUPPORT + + +INTRODUCTION +============ + + This document describes the Linux driver for Chelsio 10Gb Ethernet Network + Controller. This driver supports the Chelsio N210 NIC and is backward + compatible with the Chelsio N110 model 10Gb NICs. + + +FEATURES +======== + + Adaptive Interrupts (adaptive-rx) + --------------------------------- + + This feature provides an adaptive algorithm that adjusts the interrupt + coalescing parameters, allowing the driver to dynamically adapt the latency + settings to achieve the highest performance during various types of network + load. + + The interface used to control this feature is ethtool. Please see the + ethtool manpage for additional usage information. + + By default, adaptive-rx is disabled. + To enable adaptive-rx: + + ethtool -C adaptive-rx on + + To disable adaptive-rx, use ethtool: + + ethtool -C adaptive-rx off + + After disabling adaptive-rx, the timer latency value will be set to 50us. + You may set the timer latency after disabling adaptive-rx: + + ethtool -C rx-usecs + + An example to set the timer latency value to 100us on eth0: + + ethtool -C eth0 rx-usecs 100 + + You may also provide a timer latency value while disabling adpative-rx: + + ethtool -C adaptive-rx off rx-usecs + + If adaptive-rx is disabled and a timer latency value is specified, the timer + will be set to the specified value until changed by the user or until + adaptive-rx is enabled. + + To view the status of the adaptive-rx and timer latency values: + + ethtool -c + + + TCP Segmentation Offloading (TSO) Support + ----------------------------------------- + + This feature, also known as "large send", enables a system's protocol stack + to offload portions of outbound TCP processing to a network interface card + thereby reducing system CPU utilization and enhancing performance. + + The interface used to control this feature is ethtool version 1.8 or higher. + Please see the ethtool manpage for additional usage information. + + By default, TSO is enabled. + To disable TSO: + + ethtool -K tso off + + To enable TSO: + + ethtool -K tso on + + To view the status of TSO: + + ethtool -k + + +PERFORMANCE +=========== + + The following information is provided as an example of how to change system + parameters for "performance tuning" an what value to use. You may or may not + want to change these system parameters, depending on your server/workstation + application. Doing so is not warranted in any way by Chelsio Communications, + and is done at "YOUR OWN RISK". Chelsio will not be held responsible for loss + of data or damage to equipment. + + Your distribution may have a different way of doing things, or you may prefer + a different method. These commands are shown only to provide an example of + what to do and are by no means definitive. + + Making any of the following system changes will only last until you reboot + your system. You may want to write a script that runs at boot-up which + includes the optimal settings for your system. + + Setting PCI Latency Timer: + setpci -d 1425:* 0x0c.l=0x0000F800 + + Disabling TCP timestamp: + sysctl -w net.ipv4.tcp_timestamps=0 + + Disabling SACK: + sysctl -w net.ipv4.tcp_sack=0 + + Setting large number of incoming connection requests: + sysctl -w net.ipv4.tcp_max_syn_backlog=3000 + + Setting maximum receive socket buffer size: + sysctl -w net.core.rmem_max=1024000 + + Setting maximum send socket buffer size: + sysctl -w net.core.wmem_max=1024000 + + Set smp_affinity (on a multiprocessor system) to a single CPU: + echo 1 > /proc/irq//smp_affinity + + Setting default receive socket buffer size: + sysctl -w net.core.rmem_default=524287 + + Setting default send socket buffer size: + sysctl -w net.core.wmem_default=524287 + + Setting maximum option memory buffers: + sysctl -w net.core.optmem_max=524287 + + Setting maximum backlog (# of unprocessed packets before kernel drops): + sysctl -w net.core.netdev_max_backlog=300000 + + Setting TCP read buffers (min/default/max): + sysctl -w net.ipv4.tcp_rmem="10000000 10000000 10000000" + + Setting TCP write buffers (min/pressure/max): + sysctl -w net.ipv4.tcp_wmem="10000000 10000000 10000000" + + Setting TCP buffer space (min/pressure/max): + sysctl -w net.ipv4.tcp_mem="10000000 10000000 10000000" + + TCP window size for single connections: + The receive buffer (RX_WINDOW) size must be at least as large as the + Bandwidth-Delay Product of the communication link between the sender and + receiver. Due to the variations of RTT, you may want to increase the buffer + size up to 2 times the Bandwidth-Delay Product. Reference page 289 of + "TCP/IP Illustrated, Volume 1, The Protocols" by W. Richard Stevens. + At 10Gb speeds, use the following formula: + RX_WINDOW >= 1.25MBytes * RTT(in milliseconds) + Example for RTT with 100us: RX_WINDOW = (1,250,000 * 0.1) = 125,000 + RX_WINDOW sizes of 256KB - 512KB should be sufficient. + Setting the min, max, and default receive buffer (RX_WINDOW) size: + sysctl -w net.ipv4.tcp_rmem=" " + + TCP window size for multiple connections: + The receive buffer (RX_WINDOW) size may be calculated the same as single + connections, but should be divided by the number of connections. The + smaller window prevents congestion and facilitates better pacing, + especially if/when MAC level flow control does not work well or when it is + not supported on the machine. Experimentation may be necessary to attain + the correct value. This method is provided as a starting point fot the + correct receive buffer size. + Setting the min, max, and default receive buffer (RX_WINDOW) size is + performed in the same manner as single connection. + + +DRIVER MESSAGES +=============== + + The following messages are the most common messages logged by syslog. These + may be found in /var/log/messages. + + Driver up: + Chelsio Network Driver - version 2.1.1 + + NIC detected: + eth#: Chelsio N210 1x10GBaseX NIC (rev #), PCIX 133MHz/64-bit + + Link up: + eth#: link is up at 10 Gbps, full duplex + + Link down: + eth#: link is down + + +KNOWN ISSUES +============ + + These issues have been identified during testing. The following information + is provided as a workaround to the problem. In some cases, this problem is + inherent to Linux or to a particular Linux Distribution and/or hardware + platform. + + 1. Large number of TCP retransmits on a multiprocessor (SMP) system. + + On a system with multiple CPUs, the interrupt (IRQ) for the network + controller may be bound to more than one CPU. This will cause TCP + retransmits if the packet data were to be split across different CPUs + and re-assembled in a different order than expected. + + To eliminate the TCP retransmits, set smp_affinity on the particular + interrupt to a single CPU. You can locate the interrupt (IRQ) used on + the N110/N210 by using ifconfig: + ifconfig | grep Interrupt + Set the smp_affinity to a single CPU: + echo 1 > /proc/irq//smp_affinity + + It is highly suggested that you do not run the irqbalance daemon on your + system, as this will change any smp_affinity setting you have applied. + The irqbalance daemon runs on a 10 second interval and binds interrupts + to the least loaded CPU determined by the daemon. To disable this daemon: + chkconfig --level 2345 irqbalance off + + By default, some Linux distributions enable the kernel feature, + irqbalance, which performs the same function as the daemon. To disable + this feature, add the following line to your bootloader: + noirqbalance + + Example using the Grub bootloader: + title Red Hat Enterprise Linux AS (2.4.21-27.ELsmp) + root (hd0,0) + kernel /vmlinuz-2.4.21-27.ELsmp ro root=/dev/hda3 noirqbalance + initrd /initrd-2.4.21-27.ELsmp.img + + 2. After running insmod, the driver is loaded and the incorrect network + interface is brought up without running ifup. + + When using 2.4.x kernels, including RHEL kernels, the Linux kernel + invokes a script named "hotplug". This script is primarily used to + automatically bring up USB devices when they are plugged in, however, + the script also attempts to automatically bring up a network interface + after loading the kernel module. The hotplug script does this by scanning + the ifcfg-eth# config files in /etc/sysconfig/network-scripts, looking + for HWADDR=. + + If the hotplug script does not find the HWADDRR within any of the + ifcfg-eth# files, it will bring up the device with the next available + interface name. If this interface is already configured for a different + network card, your new interface will have incorrect IP address and + network settings. + + To solve this issue, you can add the HWADDR= key to the + interface config file of your network controller. + + To disable this "hotplug" feature, you may add the driver (module name) + to the "blacklist" file located in /etc/hotplug. It has been noted that + this does not work for network devices because the net.agent script + does not use the blacklist file. Simply remove, or rename, the net.agent + script located in /etc/hotplug to disable this feature. + + 3. Transport Protocol (TP) hangs when running heavy multi-connection traffic + on an AMD Opteron system with HyperTransport PCI-X Tunnel chipset. + + If your AMD Opteron system uses the AMD-8131 HyperTransport PCI-X Tunnel + chipset, you may experience the "133-Mhz Mode Split Completion Data + Corruption" bug identified by AMD while using a 133Mhz PCI-X card on the + bus PCI-X bus. + + AMD states, "Under highly specific conditions, the AMD-8131 PCI-X Tunnel + can provide stale data via split completion cycles to a PCI-X card that + is operating at 133 Mhz", causing data corruption. + + AMD's provides three workarounds for this problem, however, Chelsio + recommends the first option for best performance with this bug: + + For 133Mhz secondary bus operation, limit the transaction length and + the number of outstanding transactions, via BIOS configuration + programming of the PCI-X card, to the following: + + Data Length (bytes): 1k + Total allowed outstanding transactions: 2 + + Please refer to AMD 8131-HT/PCI-X Errata 26310 Rev 3.08 August 2004, + section 56, "133-MHz Mode Split Completion Data Corruption" for more + details with this bug and workarounds suggested by AMD. + + It may be possible to work outside AMD's recommended PCI-X settings, try + increasing the Data Length to 2k bytes for increased performance. If you + have issues with these settings, please revert to the "safe" settings + and duplicate the problem before submitting a bug or asking for support. + + NOTE: The default setting on most systems is 8 outstanding transactions + and 2k bytes data length. + + 4. On multiprocessor systems, it has been noted that an application which + is handling 10Gb networking can switch between CPUs causing degraded + and/or unstable performance. + + If running on an SMP system and taking performance measurements, it + is suggested you either run the latest netperf-2.4.0+ or use a binding + tool such as Tim Hockin's procstate utilities (runon) + . + + Binding netserver and netperf (or other applications) to particular + CPUs will have a significant difference in performance measurements. + You may need to experiment which CPU to bind the application to in + order to achieve the best performance for your system. + + If you are developing an application designed for 10Gb networking, + please keep in mind you may want to look at kernel functions + sched_setaffinity & sched_getaffinity to bind your application. + + If you are just running user-space applications such as ftp, telnet, + etc., you may want to try the runon tool provided by Tim Hockin's + procstate utility. You could also try binding the interface to a + particular CPU: runon 0 ifup eth0 + + +SUPPORT +======= + + If you have problems with the software or hardware, please contact our + customer support team via email at support@chelsio.com or check our website + at http://www.chelsio.com + +=============================================================================== + + Chelsio Communications + 370 San Aleso Ave. + Suite 100 + Sunnyvale, CA 94085 + http://www.chelsio.com + +This program is free software; you can redistribute it and/or modify +it under the terms of the GNU General Public License, version 2, as +published by the Free Software Foundation. + +You should have received a copy of the GNU General Public License along +with this program; if not, write to the Free Software Foundation, Inc., +59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. + +THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED +WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF +MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. + + Copyright (c) 2003-2005 Chelsio Communications. All rights reserved. + +=============================================================================== Index: drivers/net/Kconfig =================================================================== --- 4f1caf9899c1859277082422b1fc37901c6097ac/drivers/net/Kconfig (mode:100644) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/Kconfig (mode:100644) @@ -2091,6 +2091,25 @@ menu "Ethernet (10000 Mbit)" depends on NETDEVICES && !UML +config CHELSIO_T1 + tristate "Chelsio 10Gb Ethernet support" + depends on PCI + help + This driver supports Chelsio N110 and N210 models 10Gb Ethernet + cards. More information about adapter features and performance + tuning is in . + + For general information about Chelsio and our products, visit + our website at . + + For customer support, please visit our customer support page at + . + + Please send feedback to . + + To compile this driver as a module, choose M here: the module + will be called cxgb. + config IXGB tristate "Intel(R) PRO/10GbE support" depends on PCI Index: drivers/net/Makefile =================================================================== --- 4f1caf9899c1859277082422b1fc37901c6097ac/drivers/net/Makefile (mode:100644) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/Makefile (mode:100644) @@ -9,6 +9,7 @@ obj-$(CONFIG_E1000) += e1000/ obj-$(CONFIG_IBM_EMAC) += ibm_emac/ obj-$(CONFIG_IXGB) += ixgb/ +obj-$(CONFIG_CHELSIO_T1) += chelsio/ obj-$(CONFIG_BONDING) += bonding/ obj-$(CONFIG_GIANFAR) += gianfar_driver.o Index: drivers/net/chelsio/Makefile =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/Makefile (mode:100644) @@ -0,0 +1,11 @@ +# +# Chelsio 10Gb NIC driver for Linux. +# + +obj-$(CONFIG_CHELSIO_T1) += cxgb.o + +EXTRA_CFLAGS += -I$(TOPDIR)/drivers/net/chelsio $(DEBUG_FLAGS) + + +cxgb-objs := cxgb2.o espi.o pm3393.o sge.o subr.o mv88x201x.o + Index: drivers/net/chelsio/common.h =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/common.h (mode:100644) @@ -0,0 +1,314 @@ +/***************************************************************************** + * * + * File: common.h * + * $Revision: 1.21 $ * + * $Date: 2005/06/22 00:43:25 $ * + * Description: * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#ifndef _CXGB_COMMON_H_ +#define _CXGB_COMMON_H_ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRV_DESCRIPTION "Chelsio 10Gb Ethernet Driver" +#define DRV_NAME "cxgb" +#define DRV_VERSION "2.1.1" +#define PFX DRV_NAME ": " + +#define CH_ERR(fmt, ...) printk(KERN_ERR PFX fmt, ## __VA_ARGS__) +#define CH_WARN(fmt, ...) printk(KERN_WARNING PFX fmt, ## __VA_ARGS__) +#define CH_ALERT(fmt, ...) printk(KERN_ALERT PFX fmt, ## __VA_ARGS__) + +#define CH_DEVICE(devid, ssid, idx) \ + { PCI_VENDOR_ID_CHELSIO, devid, PCI_ANY_ID, ssid, 0, 0, idx } + +#define SUPPORTED_PAUSE (1 << 13) +#define SUPPORTED_LOOPBACK (1 << 15) + +#define ADVERTISED_PAUSE (1 << 13) +#define ADVERTISED_ASYM_PAUSE (1 << 14) + +typedef struct adapter adapter_t; + +void t1_elmer0_ext_intr(adapter_t *adapter); +void t1_link_changed(adapter_t *adapter, int port_id, int link_status, + int speed, int duplex, int fc); + +struct t1_rx_mode { + struct net_device *dev; + u32 idx; + struct dev_mc_list *list; +}; + +#define t1_rx_mode_promisc(rm) (rm->dev->flags & IFF_PROMISC) +#define t1_rx_mode_allmulti(rm) (rm->dev->flags & IFF_ALLMULTI) +#define t1_rx_mode_mc_cnt(rm) (rm->dev->mc_count) + +static inline u8 *t1_get_next_mcaddr(struct t1_rx_mode *rm) +{ + u8 *addr = 0; + + if (rm->idx++ < rm->dev->mc_count) { + addr = rm->list->dmi_addr; + rm->list = rm->list->next; + } + return addr; +} + +#define MAX_NPORTS 4 + +#define SPEED_INVALID 0xffff +#define DUPLEX_INVALID 0xff + +enum { + CHBT_BOARD_N110, + CHBT_BOARD_N210 +}; + +enum { + CHBT_TERM_T1, + CHBT_TERM_T2 +}; + +enum { + CHBT_MAC_PM3393, +}; + +enum { + CHBT_PHY_88X2010, +}; + +enum { + PAUSE_RX = 1 << 0, + PAUSE_TX = 1 << 1, + PAUSE_AUTONEG = 1 << 2 +}; + +/* Revisions of T1 chip */ +enum { + TERM_T1A = 0, + TERM_T1B = 1, + TERM_T2 = 3 +}; + +struct sge_params { + unsigned int cmdQ_size[2]; + unsigned int freelQ_size[2]; + unsigned int large_buf_capacity; + unsigned int rx_coalesce_usecs; + unsigned int last_rx_coalesce_raw; + unsigned int default_rx_coalesce_usecs; + unsigned int sample_interval_usecs; + unsigned int coalesce_enable; + unsigned int polling; +}; + +struct chelsio_pci_params { + unsigned short speed; + unsigned char width; + unsigned char is_pcix; +}; + +struct adapter_params { + struct sge_params sge; + struct chelsio_pci_params pci; + + const struct board_info *brd_info; + + unsigned int nports; /* # of ethernet ports */ + unsigned int stats_update_period; + unsigned short chip_revision; + unsigned char chip_version; +}; + +struct link_config { + unsigned int supported; /* link capabilities */ + unsigned int advertising; /* advertised capabilities */ + unsigned short requested_speed; /* speed user has requested */ + unsigned short speed; /* actual link speed */ + unsigned char requested_duplex; /* duplex user has requested */ + unsigned char duplex; /* actual link duplex */ + unsigned char requested_fc; /* flow control user has requested */ + unsigned char fc; /* actual link flow control */ + unsigned char autoneg; /* autonegotiating? */ +}; + +struct cmac; +struct cphy; + +struct port_info { + struct net_device *dev; + struct cmac *mac; + struct cphy *phy; + struct link_config link_config; + struct net_device_stats netstats; +}; + +struct sge; +struct peespi; + +struct adapter { + u8 *regs; + struct pci_dev *pdev; + unsigned long registered_device_map; + unsigned long open_device_map; + unsigned long flags; + + const char *name; + int msg_enable; + u32 mmio_len; + + struct work_struct ext_intr_handler_task; + struct adapter_params params; + + struct vlan_group *vlan_grp; + + /* Terminator modules. */ + struct sge *sge; + struct peespi *espi; + + struct port_info port[MAX_NPORTS]; + struct work_struct stats_update_task; + struct timer_list stats_update_timer; + + struct semaphore mib_mutex; + spinlock_t tpi_lock; + spinlock_t work_lock; + /* guards async operations */ + spinlock_t async_lock ____cacheline_aligned; + u32 slow_intr_mask; +}; + +enum { /* adapter flags */ + FULL_INIT_DONE = 1 << 0, + TSO_CAPABLE = 1 << 2, + TCP_CSUM_CAPABLE = 1 << 3, + UDP_CSUM_CAPABLE = 1 << 4, + VLAN_ACCEL_CAPABLE = 1 << 5, + RX_CSUM_ENABLED = 1 << 6, +}; + +struct mdio_ops; +struct gmac; +struct gphy; + +struct board_info { + unsigned char board; + unsigned char port_number; + unsigned long caps; + unsigned char chip_term; + unsigned char chip_mac; + unsigned char chip_phy; + unsigned int clock_core; + unsigned int clock_mc3; + unsigned int clock_mc4; + unsigned int espi_nports; + unsigned int clock_cspi; + unsigned int clock_elmer0; + unsigned char mdio_mdien; + unsigned char mdio_mdiinv; + unsigned char mdio_mdc; + unsigned char mdio_phybaseaddr; + struct gmac *gmac; + struct gphy *gphy; + struct mdio_ops *mdio_ops; + const char *desc; +}; + +extern struct pci_device_id t1_pci_tbl[]; + +static inline int adapter_matches_type(const adapter_t *adapter, + int version, int revision) +{ + return adapter->params.chip_version == version && + adapter->params.chip_revision == revision; +} + +#define t1_is_T1B(adap) adapter_matches_type(adap, CHBT_TERM_T1, TERM_T1B) +#define is_T2(adap) adapter_matches_type(adap, CHBT_TERM_T2, TERM_T2) + +/* Returns true if an adapter supports VLAN acceleration and TSO */ +static inline int vlan_tso_capable(const adapter_t *adapter) +{ + return !t1_is_T1B(adapter); +} + +#define for_each_port(adapter, iter) \ + for (iter = 0; iter < (adapter)->params.nports; ++iter) + +#define board_info(adapter) ((adapter)->params.brd_info) +#define is_10G(adapter) (board_info(adapter)->caps & SUPPORTED_10000baseT_Full) + +static inline unsigned int core_ticks_per_usec(const adapter_t *adap) +{ + return board_info(adap)->clock_core / 1000000; +} + +extern int t1_tpi_write(adapter_t *adapter, u32 addr, u32 value); +extern int t1_tpi_read(adapter_t *adapter, u32 addr, u32 *value); + +extern void t1_interrupts_enable(adapter_t *adapter); +extern void t1_interrupts_disable(adapter_t *adapter); +extern void t1_interrupts_clear(adapter_t *adapter); +extern int elmer0_ext_intr_handler(adapter_t *adapter); +extern int t1_slow_intr_handler(adapter_t *adapter); + +extern int t1_link_start(struct cphy *phy, struct cmac *mac, struct link_config *lc); +extern const struct board_info *t1_get_board_info(unsigned int board_id); +extern const struct board_info *t1_get_board_info_from_ids(unsigned int devid, + unsigned short ssid); +extern int t1_seeprom_read(adapter_t *adapter, u32 addr, u32 *data); +extern int t1_get_board_rev(adapter_t *adapter, const struct board_info *bi, + struct adapter_params *p); +extern int t1_init_hw_modules(adapter_t *adapter); +extern int t1_init_sw_modules(adapter_t *adapter, const struct board_info *bi); +extern void t1_free_sw_modules(adapter_t *adapter); +extern void t1_fatal_err(adapter_t *adapter); + +extern void t1_tp_set_udp_checksum_offload(adapter_t *adapter, int enable); +extern void t1_tp_set_tcp_checksum_offload(adapter_t *adapter, int enable); +extern void t1_tp_set_ip_checksum_offload(adapter_t *adapter, int enable); + +#endif /* _CXGB_COMMON_H_ */ Index: drivers/net/chelsio/cphy.h =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/cphy.h (mode:100644) @@ -0,0 +1,148 @@ +/***************************************************************************** + * * + * File: cphy.h * + * $Revision: 1.7 $ * + * $Date: 2005/06/21 18:29:47 $ * + * Description: * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#ifndef _CXGB_CPHY_H_ +#define _CXGB_CPHY_H_ + +#include "common.h" + +struct mdio_ops { + void (*init)(adapter_t *adapter, const struct board_info *bi); + int (*read)(adapter_t *adapter, int phy_addr, int mmd_addr, + int reg_addr, unsigned int *val); + int (*write)(adapter_t *adapter, int phy_addr, int mmd_addr, + int reg_addr, unsigned int val); +}; + +/* PHY interrupt types */ +enum { + cphy_cause_link_change = 0x1, + cphy_cause_error = 0x2 +}; + +struct cphy; + +/* PHY operations */ +struct cphy_ops { + void (*destroy)(struct cphy *); + int (*reset)(struct cphy *, int wait); + + int (*interrupt_enable)(struct cphy *); + int (*interrupt_disable)(struct cphy *); + int (*interrupt_clear)(struct cphy *); + int (*interrupt_handler)(struct cphy *); + + int (*autoneg_enable)(struct cphy *); + int (*autoneg_disable)(struct cphy *); + int (*autoneg_restart)(struct cphy *); + + int (*advertise)(struct cphy *phy, unsigned int advertise_map); + int (*set_loopback)(struct cphy *, int on); + int (*set_speed_duplex)(struct cphy *phy, int speed, int duplex); + int (*get_link_status)(struct cphy *phy, int *link_ok, int *speed, + int *duplex, int *fc); +}; + +/* A PHY instance */ +struct cphy { + int addr; /* PHY address */ + adapter_t *adapter; /* associated adapter */ + struct cphy_ops *ops; /* PHY operations */ + int (*mdio_read)(adapter_t *adapter, int phy_addr, int mmd_addr, + int reg_addr, unsigned int *val); + int (*mdio_write)(adapter_t *adapter, int phy_addr, int mmd_addr, + int reg_addr, unsigned int val); + struct cphy_instance *instance; +}; + +/* Convenience MDIO read/write wrappers */ +static inline int mdio_read(struct cphy *cphy, int mmd, int reg, + unsigned int *valp) +{ + return cphy->mdio_read(cphy->adapter, cphy->addr, mmd, reg, valp); +} + +static inline int mdio_write(struct cphy *cphy, int mmd, int reg, + unsigned int val) +{ + return cphy->mdio_write(cphy->adapter, cphy->addr, mmd, reg, val); +} + +static inline int simple_mdio_read(struct cphy *cphy, int reg, + unsigned int *valp) +{ + return mdio_read(cphy, 0, reg, valp); +} + +static inline int simple_mdio_write(struct cphy *cphy, int reg, + unsigned int val) +{ + return mdio_write(cphy, 0, reg, val); +} + +/* Convenience initializer */ +static inline void cphy_init(struct cphy *phy, adapter_t *adapter, + int phy_addr, struct cphy_ops *phy_ops, + struct mdio_ops *mdio_ops) +{ + phy->adapter = adapter; + phy->addr = phy_addr; + phy->ops = phy_ops; + if (mdio_ops) { + phy->mdio_read = mdio_ops->read; + phy->mdio_write = mdio_ops->write; + } +} + +/* Operations of the PHY-instance factory */ +struct gphy { + /* Construct a PHY instance with the given PHY address */ + struct cphy *(*create)(adapter_t *adapter, int phy_addr, + struct mdio_ops *mdio_ops); + + /* + * Reset the PHY chip. This resets the whole PHY chip, not individual + * ports. + */ + int (*reset)(adapter_t *adapter); +}; + +extern struct gphy t1_mv88x201x_ops; +extern struct gphy t1_dummy_phy_ops; + +#endif /* _CXGB_CPHY_H_ */ Index: drivers/net/chelsio/cpl5_cmd.h =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/cpl5_cmd.h (mode:100644) @@ -0,0 +1,145 @@ +/***************************************************************************** + * * + * File: cpl5_cmd.h * + * $Revision: 1.6 $ * + * $Date: 2005/06/21 18:29:47 $ * + * Description: * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#ifndef _CXGB_CPL5_CMD_H_ +#define _CXGB_CPL5_CMD_H_ + +#include + +#if !defined(__LITTLE_ENDIAN_BITFIELD) && !defined(__BIG_ENDIAN_BITFIELD) +#error "Adjust your defines" +#endif + +enum CPL_opcode { + CPL_RX_PKT = 0xAD, + CPL_TX_PKT = 0xB2, + CPL_TX_PKT_LSO = 0xB6, +}; + +enum { /* TX_PKT_LSO ethernet types */ + CPL_ETH_II, + CPL_ETH_II_VLAN, + CPL_ETH_802_3, + CPL_ETH_802_3_VLAN +}; + +struct cpl_rx_data { + u32 rsvd0; + u32 len; + u32 seq; + u16 urg; + u8 rsvd1; + u8 status; +}; + +/* + * We want this header's alignment to be no more stringent than 2-byte aligned. + * All fields are u8 or u16 except for the length. However that field is not + * used so we break it into 2 16-bit parts to easily meet our alignment needs. + */ +struct cpl_tx_pkt { + u8 opcode; +#if defined(__LITTLE_ENDIAN_BITFIELD) + u8 iff:4; + u8 ip_csum_dis:1; + u8 l4_csum_dis:1; + u8 vlan_valid:1; + u8 rsvd:1; +#else + u8 rsvd:1; + u8 vlan_valid:1; + u8 l4_csum_dis:1; + u8 ip_csum_dis:1; + u8 iff:4; +#endif + u16 vlan; + u16 len_hi; + u16 len_lo; +}; + +struct cpl_tx_pkt_lso { + u8 opcode; +#if defined(__LITTLE_ENDIAN_BITFIELD) + u8 iff:4; + u8 ip_csum_dis:1; + u8 l4_csum_dis:1; + u8 vlan_valid:1; + u8 rsvd:1; +#else + u8 rsvd:1; + u8 vlan_valid:1; + u8 l4_csum_dis:1; + u8 ip_csum_dis:1; + u8 iff:4; +#endif + u16 vlan; + u32 len; + + u32 rsvd2; + u8 rsvd3; +#if defined(__LITTLE_ENDIAN_BITFIELD) + u8 tcp_hdr_words:4; + u8 ip_hdr_words:4; +#else + u8 ip_hdr_words:4; + u8 tcp_hdr_words:4; +#endif + u16 eth_type_mss; +}; + +struct cpl_rx_pkt { + u8 opcode; +#if defined(__LITTLE_ENDIAN_BITFIELD) + u8 iff:4; + u8 csum_valid:1; + u8 bad_pkt:1; + u8 vlan_valid:1; + u8 rsvd:1; +#else + u8 rsvd:1; + u8 vlan_valid:1; + u8 bad_pkt:1; + u8 csum_valid:1; + u8 iff:4; +#endif + u16 csum; + u16 vlan; + u16 len; +}; + +#endif /* _CXGB_CPL5_CMD_H_ */ Index: drivers/net/chelsio/cxgb2.c =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/cxgb2.c (mode:100644) @@ -0,0 +1,1256 @@ +/***************************************************************************** + * * + * File: cxgb2.c * + * $Revision: 1.25 $ * + * $Date: 2005/06/22 00:43:25 $ * + * Description: * + * Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#include "common.h" +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "cpl5_cmd.h" +#include "regs.h" +#include "gmac.h" +#include "cphy.h" +#include "sge.h" +#include "espi.h" + +#ifdef work_struct +#include +#define INIT_WORK INIT_TQUEUE +#define schedule_work schedule_task +#define flush_scheduled_work flush_scheduled_tasks + +static inline void schedule_mac_stats_update(struct adapter *ap, int secs) +{ + mod_timer(&ap->stats_update_timer, jiffies + secs * HZ); +} + +static inline void cancel_mac_stats_update(struct adapter *ap) +{ + del_timer_sync(&ap->stats_update_timer); + flush_scheduled_tasks(); +} + +/* + * Stats update timer for 2.4. It schedules a task to do the actual update as + * we need to access MAC statistics in process context. + */ +static void mac_stats_timer(unsigned long data) +{ + struct adapter *ap = (struct adapter *)data; + + schedule_task(&ap->stats_update_task); +} +#else +#include + +static inline void schedule_mac_stats_update(struct adapter *ap, int secs) +{ + schedule_delayed_work(&ap->stats_update_task, secs * HZ); +} + +static inline void cancel_mac_stats_update(struct adapter *ap) +{ + cancel_delayed_work(&ap->stats_update_task); +} +#endif + +#define MAX_CMDQ_ENTRIES 16384 +#define MAX_CMDQ1_ENTRIES 1024 +#define MAX_RX_BUFFERS 16384 +#define MAX_RX_JUMBO_BUFFERS 16384 +#define MAX_TX_BUFFERS_HIGH 16384U +#define MAX_TX_BUFFERS_LOW 1536U +#define MIN_FL_ENTRIES 32 + +#define PORT_MASK ((1 << MAX_NPORTS) - 1) + +#define DFLT_MSG_ENABLE (NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK | \ + NETIF_MSG_TIMER | NETIF_MSG_IFDOWN | NETIF_MSG_IFUP |\ + NETIF_MSG_RX_ERR | NETIF_MSG_TX_ERR) + +/* + * The EEPROM is actually bigger but only the first few bytes are used so we + * only report those. + */ +#define EEPROM_SIZE 32 + +MODULE_DESCRIPTION(DRV_DESCRIPTION); +MODULE_AUTHOR("Chelsio Communications"); +MODULE_LICENSE("GPL"); + +static int dflt_msg_enable = DFLT_MSG_ENABLE; + +MODULE_PARM(dflt_msg_enable, "i"); +MODULE_PARM_DESC(dflt_msg_enable, "Chelsio T1 message enable bitmap"); + + +static const char pci_speed[][4] = { + "33", "66", "100", "133" +}; + +/* + * Setup MAC to receive the types of packets we want. + */ +static void t1_set_rxmode(struct net_device *dev) +{ + struct adapter *adapter = dev->priv; + struct cmac *mac = adapter->port[dev->if_port].mac; + struct t1_rx_mode rm; + + rm.dev = dev; + rm.idx = 0; + rm.list = dev->mc_list; + mac->ops->set_rx_mode(mac, &rm); +} + +static void link_report(struct port_info *p) +{ + if (!netif_carrier_ok(p->dev)) + printk(KERN_INFO "%s: link down\n", p->dev->name); + else { + const char *s = "10Mbps"; + + switch (p->link_config.speed) { + case SPEED_10000: s = "10Gbps"; break; + case SPEED_1000: s = "1000Mbps"; break; + case SPEED_100: s = "100Mbps"; break; + } + + printk(KERN_INFO "%s: link up, %s, %s-duplex\n", + p->dev->name, s, + p->link_config.duplex == DUPLEX_FULL ? "full" : "half"); + } +} + +void t1_link_changed(struct adapter *adapter, int port_id, int link_stat, + int speed, int duplex, int pause) +{ + struct port_info *p = &adapter->port[port_id]; + + if (link_stat != netif_carrier_ok(p->dev)) { + if (link_stat) + netif_carrier_on(p->dev); + else + netif_carrier_off(p->dev); + link_report(p); + + } +} + +static void link_start(struct port_info *p) +{ + struct cmac *mac = p->mac; + + mac->ops->reset(mac); + if (mac->ops->macaddress_set) + mac->ops->macaddress_set(mac, p->dev->dev_addr); + t1_set_rxmode(p->dev); + t1_link_start(p->phy, mac, &p->link_config); + mac->ops->enable(mac, MAC_DIRECTION_RX | MAC_DIRECTION_TX); +} + +static void enable_hw_csum(struct adapter *adapter) +{ + if (adapter->flags & TSO_CAPABLE) + t1_tp_set_ip_checksum_offload(adapter, 1); /* for TSO only */ + t1_tp_set_tcp_checksum_offload(adapter, 1); +} + +/* + * Things to do upon first use of a card. + * This must run with the rtnl lock held. + */ +static int cxgb_up(struct adapter *adapter) +{ + int err = 0; + + if (!(adapter->flags & FULL_INIT_DONE)) { + err = t1_init_hw_modules(adapter); + if (err) + goto out_err; + + enable_hw_csum(adapter); + adapter->flags |= FULL_INIT_DONE; + } + + t1_interrupts_clear(adapter); + if ((err = request_irq(adapter->pdev->irq, + t1_select_intr_handler(adapter), SA_SHIRQ, + adapter->name, adapter))) { + goto out_err; + } + t1_sge_start(adapter->sge); + t1_interrupts_enable(adapter); + out_err: + return err; +} + +/* + * Release resources when all the ports have been stopped. + */ +static void cxgb_down(struct adapter *adapter) +{ + t1_sge_stop(adapter->sge); + t1_interrupts_disable(adapter); + free_irq(adapter->pdev->irq, adapter); +} + +static int cxgb_open(struct net_device *dev) +{ + int err; + struct adapter *adapter = dev->priv; + int other_ports = adapter->open_device_map & PORT_MASK; + + if (!adapter->open_device_map && (err = cxgb_up(adapter)) < 0) + return err; + + __set_bit(dev->if_port, &adapter->open_device_map); + link_start(&adapter->port[dev->if_port]); + netif_start_queue(dev); + if (!other_ports && adapter->params.stats_update_period) + schedule_mac_stats_update(adapter, + adapter->params.stats_update_period); + return 0; +} + +static int cxgb_close(struct net_device *dev) +{ + struct adapter *adapter = dev->priv; + struct port_info *p = &adapter->port[dev->if_port]; + struct cmac *mac = p->mac; + + netif_stop_queue(dev); + mac->ops->disable(mac, MAC_DIRECTION_TX | MAC_DIRECTION_RX); + netif_carrier_off(dev); + + clear_bit(dev->if_port, &adapter->open_device_map); + if (adapter->params.stats_update_period && + !(adapter->open_device_map & PORT_MASK)) { + /* Stop statistics accumulation. */ + smp_mb__after_clear_bit(); + spin_lock(&adapter->work_lock); /* sync with update task */ + spin_unlock(&adapter->work_lock); + cancel_mac_stats_update(adapter); + } + + if (!adapter->open_device_map) + cxgb_down(adapter); + return 0; +} + +static struct net_device_stats *t1_get_stats(struct net_device *dev) +{ + struct adapter *adapter = dev->priv; + struct port_info *p = &adapter->port[dev->if_port]; + struct net_device_stats *ns = &p->netstats; + const struct cmac_statistics *pstats; + + /* Do a full update of the MAC stats */ + pstats = p->mac->ops->statistics_update(p->mac, + MAC_STATS_UPDATE_FULL); + + ns->tx_packets = pstats->TxUnicastFramesOK + + pstats->TxMulticastFramesOK + pstats->TxBroadcastFramesOK; + + ns->rx_packets = pstats->RxUnicastFramesOK + + pstats->RxMulticastFramesOK + pstats->RxBroadcastFramesOK; + + ns->tx_bytes = pstats->TxOctetsOK; + ns->rx_bytes = pstats->RxOctetsOK; + + ns->tx_errors = pstats->TxLateCollisions + pstats->TxLengthErrors + + pstats->TxUnderrun + pstats->TxFramesAbortedDueToXSCollisions; + ns->rx_errors = pstats->RxDataErrors + pstats->RxJabberErrors + + pstats->RxFCSErrors + pstats->RxAlignErrors + + pstats->RxSequenceErrors + pstats->RxFrameTooLongErrors + + pstats->RxSymbolErrors + pstats->RxRuntErrors; + + ns->multicast = pstats->RxMulticastFramesOK; + ns->collisions = pstats->TxTotalCollisions; + + /* detailed rx_errors */ + ns->rx_length_errors = pstats->RxFrameTooLongErrors + + pstats->RxJabberErrors; + ns->rx_over_errors = 0; + ns->rx_crc_errors = pstats->RxFCSErrors; + ns->rx_frame_errors = pstats->RxAlignErrors; + ns->rx_fifo_errors = 0; + ns->rx_missed_errors = 0; + + /* detailed tx_errors */ + ns->tx_aborted_errors = pstats->TxFramesAbortedDueToXSCollisions; + ns->tx_carrier_errors = 0; + ns->tx_fifo_errors = pstats->TxUnderrun; + ns->tx_heartbeat_errors = 0; + ns->tx_window_errors = pstats->TxLateCollisions; + return ns; +} + +static u32 get_msglevel(struct net_device *dev) +{ + struct adapter *adapter = dev->priv; + + return adapter->msg_enable; +} + +static void set_msglevel(struct net_device *dev, u32 val) +{ + struct adapter *adapter = dev->priv; + + adapter->msg_enable = val; +} + +static char stats_strings[][ETH_GSTRING_LEN] = { + "TxOctetsOK", + "TxOctetsBad", + "TxUnicastFramesOK", + "TxMulticastFramesOK", + "TxBroadcastFramesOK", + "TxPauseFrames", + "TxFramesWithDeferredXmissions", + "TxLateCollisions", + "TxTotalCollisions", + "TxFramesAbortedDueToXSCollisions", + "TxUnderrun", + "TxLengthErrors", + "TxInternalMACXmitError", + "TxFramesWithExcessiveDeferral", + "TxFCSErrors", + + "RxOctetsOK", + "RxOctetsBad", + "RxUnicastFramesOK", + "RxMulticastFramesOK", + "RxBroadcastFramesOK", + "RxPauseFrames", + "RxFCSErrors", + "RxAlignErrors", + "RxSymbolErrors", + "RxDataErrors", + "RxSequenceErrors", + "RxRuntErrors", + "RxJabberErrors", + "RxInternalMACRcvError", + "RxInRangeLengthErrors", + "RxOutOfRangeLengthField", + "RxFrameTooLongErrors", + + "TSO", + "VLANextractions", + "VLANinsertions", + "RxCsumGood", + "TxCsumOffload", + "RxDrops" + + "respQ_empty", + "respQ_overflow", + "freelistQ_empty", + "pkt_too_big", + "pkt_mismatch", + "cmdQ_full0", + "cmdQ_full1", + "tx_ipfrags", + "tx_reg_pkts", + "tx_lso_pkts", + "tx_do_cksum", + + "espi_DIP2ParityErr", + "espi_DIP4Err", + "espi_RxDrops", + "espi_TxDrops", + "espi_RxOvfl", + "espi_ParityErr" +}; + +#define T2_REGMAP_SIZE (3 * 1024) + +static int get_regs_len(struct net_device *dev) +{ + return T2_REGMAP_SIZE; +} + +static void get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info) +{ + struct adapter *adapter = dev->priv; + + strcpy(info->driver, DRV_NAME); + strcpy(info->version, DRV_VERSION); + strcpy(info->fw_version, "N/A"); + strcpy(info->bus_info, pci_name(adapter->pdev)); +} + +static int get_stats_count(struct net_device *dev) +{ + return ARRAY_SIZE(stats_strings); +} + +static void get_strings(struct net_device *dev, u32 stringset, u8 *data) +{ + if (stringset == ETH_SS_STATS) + memcpy(data, stats_strings, sizeof(stats_strings)); +} + +static void get_stats(struct net_device *dev, struct ethtool_stats *stats, + u64 *data) +{ + struct adapter *adapter = dev->priv; + struct cmac *mac = adapter->port[dev->if_port].mac; + const struct cmac_statistics *s; + const struct sge_port_stats *ss; + const struct sge_intr_counts *t; + + s = mac->ops->statistics_update(mac, MAC_STATS_UPDATE_FULL); + ss = t1_sge_get_port_stats(adapter->sge, dev->if_port); + t = t1_sge_get_intr_counts(adapter->sge); + + *data++ = s->TxOctetsOK; + *data++ = s->TxOctetsBad; + *data++ = s->TxUnicastFramesOK; + *data++ = s->TxMulticastFramesOK; + *data++ = s->TxBroadcastFramesOK; + *data++ = s->TxPauseFrames; + *data++ = s->TxFramesWithDeferredXmissions; + *data++ = s->TxLateCollisions; + *data++ = s->TxTotalCollisions; + *data++ = s->TxFramesAbortedDueToXSCollisions; + *data++ = s->TxUnderrun; + *data++ = s->TxLengthErrors; + *data++ = s->TxInternalMACXmitError; + *data++ = s->TxFramesWithExcessiveDeferral; + *data++ = s->TxFCSErrors; + + *data++ = s->RxOctetsOK; + *data++ = s->RxOctetsBad; + *data++ = s->RxUnicastFramesOK; + *data++ = s->RxMulticastFramesOK; + *data++ = s->RxBroadcastFramesOK; + *data++ = s->RxPauseFrames; + *data++ = s->RxFCSErrors; + *data++ = s->RxAlignErrors; + *data++ = s->RxSymbolErrors; + *data++ = s->RxDataErrors; + *data++ = s->RxSequenceErrors; + *data++ = s->RxRuntErrors; + *data++ = s->RxJabberErrors; + *data++ = s->RxInternalMACRcvError; + *data++ = s->RxInRangeLengthErrors; + *data++ = s->RxOutOfRangeLengthField; + *data++ = s->RxFrameTooLongErrors; + + *data++ = ss->tso; + *data++ = ss->vlan_xtract; + *data++ = ss->vlan_insert; + *data++ = ss->rx_cso_good; + *data++ = ss->tx_cso; + *data++ = ss->rx_drops; + + *data++ = (u64)t->respQ_empty; + *data++ = (u64)t->respQ_overflow; + *data++ = (u64)t->freelistQ_empty; + *data++ = (u64)t->pkt_too_big; + *data++ = (u64)t->pkt_mismatch; + *data++ = (u64)t->cmdQ_full[0]; + *data++ = (u64)t->cmdQ_full[1]; + *data++ = (u64)t->tx_ipfrags; + *data++ = (u64)t->tx_reg_pkts; + *data++ = (u64)t->tx_lso_pkts; + *data++ = (u64)t->tx_do_cksum; +} + +static inline void reg_block_dump(struct adapter *ap, void *buf, + unsigned int start, unsigned int end) +{ + u32 *p = buf + start; + + for ( ; start <= end; start += sizeof(u32)) + *p++ = readl(ap->regs + start); +} + +static void get_regs(struct net_device *dev, struct ethtool_regs *regs, + void *buf) +{ + struct adapter *ap = dev->priv; + + /* + * Version scheme: bits 0..9: chip version, bits 10..15: chip revision + */ + regs->version = 2; + + memset(buf, 0, T2_REGMAP_SIZE); + reg_block_dump(ap, buf, 0, A_SG_RESPACCUTIMER); +} + +static int get_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct adapter *adapter = dev->priv; + struct port_info *p = &adapter->port[dev->if_port]; + + cmd->supported = p->link_config.supported; + cmd->advertising = p->link_config.advertising; + + if (netif_carrier_ok(dev)) { + cmd->speed = p->link_config.speed; + cmd->duplex = p->link_config.duplex; + } else { + cmd->speed = -1; + cmd->duplex = -1; + } + + cmd->port = (cmd->supported & SUPPORTED_TP) ? PORT_TP : PORT_FIBRE; + cmd->phy_address = p->phy->addr; + cmd->transceiver = XCVR_EXTERNAL; + cmd->autoneg = p->link_config.autoneg; + cmd->maxtxpkt = 0; + cmd->maxrxpkt = 0; + return 0; +} + +static int speed_duplex_to_caps(int speed, int duplex) +{ + int cap = 0; + + switch (speed) { + case SPEED_10: + if (duplex == DUPLEX_FULL) + cap = SUPPORTED_10baseT_Full; + else + cap = SUPPORTED_10baseT_Half; + break; + case SPEED_100: + if (duplex == DUPLEX_FULL) + cap = SUPPORTED_100baseT_Full; + else + cap = SUPPORTED_100baseT_Half; + break; + case SPEED_1000: + if (duplex == DUPLEX_FULL) + cap = SUPPORTED_1000baseT_Full; + else + cap = SUPPORTED_1000baseT_Half; + break; + case SPEED_10000: + if (duplex == DUPLEX_FULL) + cap = SUPPORTED_10000baseT_Full; + } + return cap; +} + +#define ADVERTISED_MASK (ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full | \ + ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full | \ + ADVERTISED_1000baseT_Half | ADVERTISED_1000baseT_Full | \ + ADVERTISED_10000baseT_Full) + +static int set_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct adapter *adapter = dev->priv; + struct port_info *p = &adapter->port[dev->if_port]; + struct link_config *lc = &p->link_config; + + if (!(lc->supported & SUPPORTED_Autoneg)) + return -EOPNOTSUPP; /* can't change speed/duplex */ + + if (cmd->autoneg == AUTONEG_DISABLE) { + int cap = speed_duplex_to_caps(cmd->speed, cmd->duplex); + + if (!(lc->supported & cap) || cmd->speed == SPEED_1000) + return -EINVAL; + lc->requested_speed = cmd->speed; + lc->requested_duplex = cmd->duplex; + lc->advertising = 0; + } else { + cmd->advertising &= ADVERTISED_MASK; + if (cmd->advertising & (cmd->advertising - 1)) + cmd->advertising = lc->supported; + cmd->advertising &= lc->supported; + if (!cmd->advertising) + return -EINVAL; + lc->requested_speed = SPEED_INVALID; + lc->requested_duplex = DUPLEX_INVALID; + lc->advertising = cmd->advertising | ADVERTISED_Autoneg; + } + lc->autoneg = cmd->autoneg; + if (netif_running(dev)) + t1_link_start(p->phy, p->mac, lc); + return 0; +} + +static void get_pauseparam(struct net_device *dev, + struct ethtool_pauseparam *epause) +{ + struct adapter *adapter = dev->priv; + struct port_info *p = &adapter->port[dev->if_port]; + + epause->autoneg = (p->link_config.requested_fc & PAUSE_AUTONEG) != 0; + epause->rx_pause = (p->link_config.fc & PAUSE_RX) != 0; + epause->tx_pause = (p->link_config.fc & PAUSE_TX) != 0; +} + +static int set_pauseparam(struct net_device *dev, + struct ethtool_pauseparam *epause) +{ + struct adapter *adapter = dev->priv; + struct port_info *p = &adapter->port[dev->if_port]; + struct link_config *lc = &p->link_config; + + if (epause->autoneg == AUTONEG_DISABLE) + lc->requested_fc = 0; + else if (lc->supported & SUPPORTED_Autoneg) + lc->requested_fc = PAUSE_AUTONEG; + else + return -EINVAL; + + if (epause->rx_pause) + lc->requested_fc |= PAUSE_RX; + if (epause->tx_pause) + lc->requested_fc |= PAUSE_TX; + if (lc->autoneg == AUTONEG_ENABLE) { + if (netif_running(dev)) + t1_link_start(p->phy, p->mac, lc); + } else { + lc->fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX); + if (netif_running(dev)) + p->mac->ops->set_speed_duplex_fc(p->mac, -1, -1, + lc->fc); + } + return 0; +} + +static u32 get_rx_csum(struct net_device *dev) +{ + struct adapter *adapter = dev->priv; + + return (adapter->flags & RX_CSUM_ENABLED) != 0; +} + +static int set_rx_csum(struct net_device *dev, u32 data) +{ + struct adapter *adapter = dev->priv; + + if (data) + adapter->flags |= RX_CSUM_ENABLED; + else + adapter->flags &= ~RX_CSUM_ENABLED; + return 0; +} + +static int set_tso(struct net_device *dev, u32 value) +{ + struct adapter *adapter = dev->priv; + + if (!(adapter->flags & TSO_CAPABLE)) + return value ? -EOPNOTSUPP : 0; + return ethtool_op_set_tso(dev, value); +} + +static void get_sge_param(struct net_device *dev, struct ethtool_ringparam *e) +{ + struct adapter *adapter = dev->priv; + int jumbo_fl = t1_is_T1B(adapter) ? 1 : 0; + + e->rx_max_pending = MAX_RX_BUFFERS; + e->rx_mini_max_pending = 0; + e->rx_jumbo_max_pending = MAX_RX_JUMBO_BUFFERS; + e->tx_max_pending = MAX_CMDQ_ENTRIES; + + e->rx_pending = adapter->params.sge.freelQ_size[!jumbo_fl]; + e->rx_mini_pending = 0; + e->rx_jumbo_pending = adapter->params.sge.freelQ_size[jumbo_fl]; + e->tx_pending = adapter->params.sge.cmdQ_size[0]; +} + +static int set_sge_param(struct net_device *dev, struct ethtool_ringparam *e) +{ + struct adapter *adapter = dev->priv; + int jumbo_fl = t1_is_T1B(adapter) ? 1 : 0; + + if (e->rx_pending > MAX_RX_BUFFERS || e->rx_mini_pending || + e->rx_jumbo_pending > MAX_RX_JUMBO_BUFFERS || + e->tx_pending > MAX_CMDQ_ENTRIES || + e->rx_pending < MIN_FL_ENTRIES || + e->rx_jumbo_pending < MIN_FL_ENTRIES || + e->tx_pending < (adapter->params.nports + 1) * (MAX_SKB_FRAGS + 1)) + return -EINVAL; + + if (adapter->flags & FULL_INIT_DONE) + return -EBUSY; + + adapter->params.sge.freelQ_size[!jumbo_fl] = e->rx_pending; + adapter->params.sge.freelQ_size[jumbo_fl] = e->rx_jumbo_pending; + adapter->params.sge.cmdQ_size[0] = e->tx_pending; + adapter->params.sge.cmdQ_size[1] = e->tx_pending > MAX_CMDQ1_ENTRIES ? + MAX_CMDQ1_ENTRIES : e->tx_pending; + return 0; +} + +static int set_coalesce(struct net_device *dev, struct ethtool_coalesce *c) +{ + struct adapter *adapter = dev->priv; + + /* + * If RX coalescing is requested we use NAPI, otherwise interrupts. + * This choice can be made only when all ports and the TOE are off. + */ + if (adapter->open_device_map == 0) + adapter->params.sge.polling = c->use_adaptive_rx_coalesce; + + if (adapter->params.sge.polling) { + adapter->params.sge.rx_coalesce_usecs = 0; + } else { + adapter->params.sge.rx_coalesce_usecs = c->rx_coalesce_usecs; + } + adapter->params.sge.coalesce_enable = c->use_adaptive_rx_coalesce; + adapter->params.sge.sample_interval_usecs = c->rate_sample_interval; + t1_sge_set_coalesce_params(adapter->sge, &adapter->params.sge); + return 0; +} + +static int get_coalesce(struct net_device *dev, struct ethtool_coalesce *c) +{ + struct adapter *adapter = dev->priv; + + c->rx_coalesce_usecs = adapter->params.sge.rx_coalesce_usecs; + c->rate_sample_interval = adapter->params.sge.sample_interval_usecs; + c->use_adaptive_rx_coalesce = adapter->params.sge.coalesce_enable; + return 0; +} + +static int get_eeprom_len(struct net_device *dev) +{ + return EEPROM_SIZE; +} + +#define EEPROM_MAGIC(ap) \ + (PCI_VENDOR_ID_CHELSIO | ((ap)->params.chip_version << 16)) + +static int get_eeprom(struct net_device *dev, struct ethtool_eeprom *e, + u8 *data) +{ + int i; + u8 buf[EEPROM_SIZE] __attribute__((aligned(4))); + struct adapter *adapter = dev->priv; + + e->magic = EEPROM_MAGIC(adapter); + for (i = e->offset & ~3; i < e->offset + e->len; i += sizeof(u32)) + t1_seeprom_read(adapter, i, (u32 *)&buf[i]); + memcpy(data, buf + e->offset, e->len); + return 0; +} + +static struct ethtool_ops t1_ethtool_ops = { + .get_settings = get_settings, + .set_settings = set_settings, + .get_drvinfo = get_drvinfo, + .get_msglevel = get_msglevel, + .set_msglevel = set_msglevel, + .get_ringparam = get_sge_param, + .set_ringparam = set_sge_param, + .get_coalesce = get_coalesce, + .set_coalesce = set_coalesce, + .get_eeprom_len = get_eeprom_len, + .get_eeprom = get_eeprom, + .get_pauseparam = get_pauseparam, + .set_pauseparam = set_pauseparam, + .get_rx_csum = get_rx_csum, + .set_rx_csum = set_rx_csum, + .get_tx_csum = ethtool_op_get_tx_csum, + .set_tx_csum = ethtool_op_set_tx_csum, + .get_sg = ethtool_op_get_sg, + .set_sg = ethtool_op_set_sg, + .get_link = ethtool_op_get_link, + .get_strings = get_strings, + .get_stats_count = get_stats_count, + .get_ethtool_stats = get_stats, + .get_regs_len = get_regs_len, + .get_regs = get_regs, + .get_tso = ethtool_op_get_tso, + .set_tso = set_tso, +}; + +static void cxgb_proc_cleanup(struct adapter *adapter, + struct proc_dir_entry *dir) +{ + const char *name; + name = adapter->name; + remove_proc_entry(name, dir); +} +//#define chtoe_setup_toedev(adapter) NULL +#define update_mtu_tab(adapter) +#define write_smt_entry(adapter, idx) + +static int t1_ioctl(struct net_device *dev, struct ifreq *req, int cmd) +{ + struct adapter *adapter = dev->priv; + struct mii_ioctl_data *data = (struct mii_ioctl_data *)&req->ifr_data; + + switch (cmd) { + case SIOCGMIIPHY: + data->phy_id = adapter->port[dev->if_port].phy->addr; + /* FALLTHRU */ + case SIOCGMIIREG: { + struct cphy *phy = adapter->port[dev->if_port].phy; + u32 val; + + if (!phy->mdio_read) + return -EOPNOTSUPP; + phy->mdio_read(adapter, data->phy_id, 0, data->reg_num & 0x1f, + &val); + data->val_out = val; + break; + } + case SIOCSMIIREG: { + struct cphy *phy = adapter->port[dev->if_port].phy; + + if (!capable(CAP_NET_ADMIN)) + return -EPERM; + if (!phy->mdio_write) + return -EOPNOTSUPP; + phy->mdio_write(adapter, data->phy_id, 0, data->reg_num & 0x1f, + data->val_in); + break; + } + + default: + return -EOPNOTSUPP; + } + return 0; +} + +static int t1_change_mtu(struct net_device *dev, int new_mtu) +{ + int ret; + struct adapter *adapter = dev->priv; + struct cmac *mac = adapter->port[dev->if_port].mac; + + if (!mac->ops->set_mtu) + return -EOPNOTSUPP; + if (new_mtu < 68) + return -EINVAL; + if ((ret = mac->ops->set_mtu(mac, new_mtu))) + return ret; + dev->mtu = new_mtu; + return 0; +} + +static int t1_set_mac_addr(struct net_device *dev, void *p) +{ + struct adapter *adapter = dev->priv; + struct cmac *mac = adapter->port[dev->if_port].mac; + struct sockaddr *addr = p; + + if (!mac->ops->macaddress_set) + return -EOPNOTSUPP; + + memcpy(dev->dev_addr, addr->sa_data, dev->addr_len); + mac->ops->macaddress_set(mac, dev->dev_addr); + return 0; +} + +#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) +static void vlan_rx_register(struct net_device *dev, + struct vlan_group *grp) +{ + struct adapter *adapter = dev->priv; + + spin_lock_irq(&adapter->async_lock); + adapter->vlan_grp = grp; + t1_set_vlan_accel(adapter, grp != NULL); + spin_unlock_irq(&adapter->async_lock); +} + +static void vlan_rx_kill_vid(struct net_device *dev, unsigned short vid) +{ + struct adapter *adapter = dev->priv; + + spin_lock_irq(&adapter->async_lock); + if (adapter->vlan_grp) + adapter->vlan_grp->vlan_devices[vid] = NULL; + spin_unlock_irq(&adapter->async_lock); +} +#endif + +#ifdef CONFIG_NET_POLL_CONTROLLER +static void t1_netpoll(struct net_device *dev) +{ + unsigned long flags; + struct adapter *adapter = dev->priv; + + local_irq_save(flags); + t1_select_intr_handler(adapter)(adapter->pdev->irq, adapter, NULL); + local_irq_restore(flags); +} +#endif + +/* + * Periodic accumulation of MAC statistics. This is used only if the MAC + * does not have any other way to prevent stats counter overflow. + */ +static void mac_stats_task(void *data) +{ + int i; + struct adapter *adapter = data; + + for_each_port(adapter, i) { + struct port_info *p = &adapter->port[i]; + + if (netif_running(p->dev)) + p->mac->ops->statistics_update(p->mac, + MAC_STATS_UPDATE_FAST); + } + + /* Schedule the next statistics update if any port is active. */ + spin_lock(&adapter->work_lock); + if (adapter->open_device_map & PORT_MASK) + schedule_mac_stats_update(adapter, + adapter->params.stats_update_period); + spin_unlock(&adapter->work_lock); +} + +/* + * Processes elmer0 external interrupts in process context. + */ +static void ext_intr_task(void *data) +{ + struct adapter *adapter = data; + + elmer0_ext_intr_handler(adapter); + + /* Now reenable external interrupts */ + spin_lock_irq(&adapter->async_lock); + adapter->slow_intr_mask |= F_PL_INTR_EXT; + writel(F_PL_INTR_EXT, adapter->regs + A_PL_CAUSE); + writel(adapter->slow_intr_mask | F_PL_INTR_SGE_DATA, + adapter->regs + A_PL_ENABLE); + spin_unlock_irq(&adapter->async_lock); +} + +/* + * Interrupt-context handler for elmer0 external interrupts. + */ +void t1_elmer0_ext_intr(struct adapter *adapter) +{ + /* + * Schedule a task to handle external interrupts as we require + * a process context. We disable EXT interrupts in the interim + * and let the task reenable them when it's done. + */ + adapter->slow_intr_mask &= ~F_PL_INTR_EXT; + writel(adapter->slow_intr_mask | F_PL_INTR_SGE_DATA, + adapter->regs + A_PL_ENABLE); + schedule_work(&adapter->ext_intr_handler_task); +} + +void t1_fatal_err(struct adapter *adapter) +{ + if (adapter->flags & FULL_INIT_DONE) { + t1_sge_stop(adapter->sge); + t1_interrupts_disable(adapter); + } + CH_ALERT("%s: encountered fatal error, operation suspended\n", + adapter->name); +} + +static int __devinit init_one(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + static int version_printed; + + int i, err, pci_using_dac = 0; + unsigned long mmio_start, mmio_len; + const struct board_info *bi; + struct adapter *adapter = NULL; + struct port_info *pi; + + if (!version_printed) { + printk(KERN_INFO "%s - version %s\n", DRV_DESCRIPTION, + DRV_VERSION); + ++version_printed; + } + + err = pci_enable_device(pdev); + if (err) + return err; + + if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) { + CH_ERR("%s: cannot find PCI device memory base address\n", + pci_name(pdev)); + err = -ENODEV; + goto out_disable_pdev; + } + + if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) { + pci_using_dac = 1; + + if (pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK)) { + CH_ERR("%s: unable to obtain 64-bit DMA for" + "consistent allocations\n", pci_name(pdev)); + err = -ENODEV; + goto out_disable_pdev; + } + + } else if ((err = pci_set_dma_mask(pdev, DMA_32BIT_MASK)) != 0) { + CH_ERR("%s: no usable DMA configuration\n", pci_name(pdev)); + goto out_disable_pdev; + } + + err = pci_request_regions(pdev, DRV_NAME); + if (err) { + CH_ERR("%s: cannot obtain PCI resources\n", pci_name(pdev)); + goto out_disable_pdev; + } + + pci_set_master(pdev); + + mmio_start = pci_resource_start(pdev, 0); + mmio_len = pci_resource_len(pdev, 0); + bi = t1_get_board_info(ent->driver_data); + + for (i = 0; i < bi->port_number; ++i) { + struct net_device *netdev; + + netdev = alloc_etherdev(adapter ? 0 : sizeof(*adapter)); + if (!netdev) { + err = -ENOMEM; + goto out_free_dev; + } + + SET_MODULE_OWNER(netdev); + SET_NETDEV_DEV(netdev, &pdev->dev); + + if (!adapter) { + adapter = netdev->priv; + adapter->pdev = pdev; + adapter->port[0].dev = netdev; /* so we don't leak it */ + + adapter->regs = ioremap(mmio_start, mmio_len); + if (!adapter->regs) { + CH_ERR("%s: cannot map device registers\n", + pci_name(pdev)); + err = -ENOMEM; + goto out_free_dev; + } + + if (t1_get_board_rev(adapter, bi, &adapter->params)) { + err = -ENODEV; /* Can't handle this chip rev */ + goto out_free_dev; + } + + adapter->name = pci_name(pdev); + adapter->msg_enable = dflt_msg_enable; + adapter->mmio_len = mmio_len; + + init_MUTEX(&adapter->mib_mutex); + spin_lock_init(&adapter->tpi_lock); + spin_lock_init(&adapter->work_lock); + spin_lock_init(&adapter->async_lock); + + INIT_WORK(&adapter->ext_intr_handler_task, + ext_intr_task, adapter); + INIT_WORK(&adapter->stats_update_task, mac_stats_task, + adapter); +#ifdef work_struct + init_timer(&adapter->stats_update_timer); + adapter->stats_update_timer.function = mac_stats_timer; + adapter->stats_update_timer.data = + (unsigned long)adapter; +#endif + + pci_set_drvdata(pdev, netdev); + } + + pi = &adapter->port[i]; + pi->dev = netdev; + netif_carrier_off(netdev); + netdev->irq = pdev->irq; + netdev->if_port = i; + netdev->mem_start = mmio_start; + netdev->mem_end = mmio_start + mmio_len - 1; + netdev->priv = adapter; + netdev->features |= NETIF_F_SG | NETIF_F_IP_CSUM; + netdev->features |= NETIF_F_LLTX; + + adapter->flags |= RX_CSUM_ENABLED | TCP_CSUM_CAPABLE; + if (pci_using_dac) + netdev->features |= NETIF_F_HIGHDMA; + if (vlan_tso_capable(adapter)) { +#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) + adapter->flags |= VLAN_ACCEL_CAPABLE; + netdev->features |= + NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX; + netdev->vlan_rx_register = vlan_rx_register; + netdev->vlan_rx_kill_vid = vlan_rx_kill_vid; +#endif + adapter->flags |= TSO_CAPABLE; + netdev->features |= NETIF_F_TSO; + } + + netdev->open = cxgb_open; + netdev->stop = cxgb_close; + netdev->hard_start_xmit = t1_start_xmit; + netdev->hard_header_len += (adapter->flags & TSO_CAPABLE) ? + sizeof(struct cpl_tx_pkt_lso) : + sizeof(struct cpl_tx_pkt); + netdev->get_stats = t1_get_stats; + netdev->set_multicast_list = t1_set_rxmode; + netdev->do_ioctl = t1_ioctl; + netdev->change_mtu = t1_change_mtu; + netdev->set_mac_address = t1_set_mac_addr; +#ifdef CONFIG_NET_POLL_CONTROLLER + netdev->poll_controller = t1_netpoll; +#endif + netdev->weight = 64; + + SET_ETHTOOL_OPS(netdev, &t1_ethtool_ops); + } + + if (t1_init_sw_modules(adapter, bi) < 0) { + err = -ENODEV; + goto out_free_dev; + } + + /* + * The card is now ready to go. If any errors occur during device + * registration we do not fail the whole card but rather proceed only + * with the ports we manage to register successfully. However we must + * register at least one net device. + */ + for (i = 0; i < bi->port_number; ++i) { + err = register_netdev(adapter->port[i].dev); + if (err) + CH_WARN("%s: cannot register net device %s, skipping\n", + pci_name(pdev), adapter->port[i].dev->name); + else { + /* + * Change the name we use for messages to the name of + * the first successfully registered interface. + */ + if (!adapter->registered_device_map) + adapter->name = adapter->port[i].dev->name; + + __set_bit(i, &adapter->registered_device_map); + } + } + if (!adapter->registered_device_map) { + CH_ERR("%s: could not register any net devices\n", + pci_name(pdev)); + goto out_release_adapter_res; + } + + printk(KERN_INFO "%s: %s (rev %d), %s %dMHz/%d-bit\n", adapter->name, + bi->desc, adapter->params.chip_revision, + adapter->params.pci.is_pcix ? "PCIX" : "PCI", + adapter->params.pci.speed, adapter->params.pci.width); + return 0; + + out_release_adapter_res: + t1_free_sw_modules(adapter); + out_free_dev: + if (adapter) { + if (adapter->regs) iounmap(adapter->regs); + for (i = bi->port_number - 1; i >= 0; --i) + if (adapter->port[i].dev) { + cxgb_proc_cleanup(adapter, proc_root_driver); + kfree(adapter->port[i].dev); + } + } + pci_release_regions(pdev); + out_disable_pdev: + pci_disable_device(pdev); + pci_set_drvdata(pdev, NULL); + return err; +} + +static inline void t1_sw_reset(struct pci_dev *pdev) +{ + pci_write_config_dword(pdev, A_PCICFG_PM_CSR, 3); + pci_write_config_dword(pdev, A_PCICFG_PM_CSR, 0); +} + +static void __devexit remove_one(struct pci_dev *pdev) +{ + struct net_device *dev = pci_get_drvdata(pdev); + + if (dev) { + int i; + struct adapter *adapter = dev->priv; + + for_each_port(adapter, i) + if (test_bit(i, &adapter->registered_device_map)) + unregister_netdev(adapter->port[i].dev); + + t1_free_sw_modules(adapter); + iounmap(adapter->regs); + while (--i >= 0) + if (adapter->port[i].dev) { + cxgb_proc_cleanup(adapter, proc_root_driver); + kfree(adapter->port[i].dev); + } + pci_release_regions(pdev); + pci_disable_device(pdev); + pci_set_drvdata(pdev, NULL); + t1_sw_reset(pdev); + } +} + +static struct pci_driver driver = { + .name = DRV_NAME, + .id_table = t1_pci_tbl, + .probe = init_one, + .remove = __devexit_p(remove_one), +}; + +static int __init t1_init_module(void) +{ + return pci_module_init(&driver); +} + +static void __exit t1_cleanup_module(void) +{ + pci_unregister_driver(&driver); +} + +module_init(t1_init_module); +module_exit(t1_cleanup_module); Index: drivers/net/chelsio/elmer0.h =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/elmer0.h (mode:100644) @@ -0,0 +1,151 @@ +/***************************************************************************** + * * + * File: elmer0.h * + * $Revision: 1.6 $ * + * $Date: 2005/06/21 22:49:43 $ * + * Description: * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#ifndef _CXGB_ELMER0_H_ +#define _CXGB_ELMER0_H_ + +/* ELMER0 registers */ +#define A_ELMER0_VERSION 0x100000 +#define A_ELMER0_PHY_CFG 0x100004 +#define A_ELMER0_INT_ENABLE 0x100008 +#define A_ELMER0_INT_CAUSE 0x10000c +#define A_ELMER0_GPI_CFG 0x100010 +#define A_ELMER0_GPI_STAT 0x100014 +#define A_ELMER0_GPO 0x100018 +#define A_ELMER0_PORT0_MI1_CFG 0x400000 + +#define S_MI1_MDI_ENABLE 0 +#define V_MI1_MDI_ENABLE(x) ((x) << S_MI1_MDI_ENABLE) +#define F_MI1_MDI_ENABLE V_MI1_MDI_ENABLE(1U) + +#define S_MI1_MDI_INVERT 1 +#define V_MI1_MDI_INVERT(x) ((x) << S_MI1_MDI_INVERT) +#define F_MI1_MDI_INVERT V_MI1_MDI_INVERT(1U) + +#define S_MI1_PREAMBLE_ENABLE 2 +#define V_MI1_PREAMBLE_ENABLE(x) ((x) << S_MI1_PREAMBLE_ENABLE) +#define F_MI1_PREAMBLE_ENABLE V_MI1_PREAMBLE_ENABLE(1U) + +#define S_MI1_SOF 3 +#define M_MI1_SOF 0x3 +#define V_MI1_SOF(x) ((x) << S_MI1_SOF) +#define G_MI1_SOF(x) (((x) >> S_MI1_SOF) & M_MI1_SOF) + +#define S_MI1_CLK_DIV 5 +#define M_MI1_CLK_DIV 0xff +#define V_MI1_CLK_DIV(x) ((x) << S_MI1_CLK_DIV) +#define G_MI1_CLK_DIV(x) (((x) >> S_MI1_CLK_DIV) & M_MI1_CLK_DIV) + +#define A_ELMER0_PORT0_MI1_ADDR 0x400004 + +#define S_MI1_REG_ADDR 0 +#define M_MI1_REG_ADDR 0x1f +#define V_MI1_REG_ADDR(x) ((x) << S_MI1_REG_ADDR) +#define G_MI1_REG_ADDR(x) (((x) >> S_MI1_REG_ADDR) & M_MI1_REG_ADDR) + +#define S_MI1_PHY_ADDR 5 +#define M_MI1_PHY_ADDR 0x1f +#define V_MI1_PHY_ADDR(x) ((x) << S_MI1_PHY_ADDR) +#define G_MI1_PHY_ADDR(x) (((x) >> S_MI1_PHY_ADDR) & M_MI1_PHY_ADDR) + +#define A_ELMER0_PORT0_MI1_DATA 0x400008 + +#define S_MI1_DATA 0 +#define M_MI1_DATA 0xffff +#define V_MI1_DATA(x) ((x) << S_MI1_DATA) +#define G_MI1_DATA(x) (((x) >> S_MI1_DATA) & M_MI1_DATA) + +#define A_ELMER0_PORT0_MI1_OP 0x40000c + +#define S_MI1_OP 0 +#define M_MI1_OP 0x3 +#define V_MI1_OP(x) ((x) << S_MI1_OP) +#define G_MI1_OP(x) (((x) >> S_MI1_OP) & M_MI1_OP) + +#define S_MI1_ADDR_AUTOINC 2 +#define V_MI1_ADDR_AUTOINC(x) ((x) << S_MI1_ADDR_AUTOINC) +#define F_MI1_ADDR_AUTOINC V_MI1_ADDR_AUTOINC(1U) + +#define S_MI1_OP_BUSY 31 +#define V_MI1_OP_BUSY(x) ((x) << S_MI1_OP_BUSY) +#define F_MI1_OP_BUSY V_MI1_OP_BUSY(1U) + +#define A_ELMER0_PORT1_MI1_CFG 0x500000 +#define A_ELMER0_PORT1_MI1_ADDR 0x500004 +#define A_ELMER0_PORT1_MI1_DATA 0x500008 +#define A_ELMER0_PORT1_MI1_OP 0x50000c +#define A_ELMER0_PORT2_MI1_CFG 0x600000 +#define A_ELMER0_PORT2_MI1_ADDR 0x600004 +#define A_ELMER0_PORT2_MI1_DATA 0x600008 +#define A_ELMER0_PORT2_MI1_OP 0x60000c +#define A_ELMER0_PORT3_MI1_CFG 0x700000 +#define A_ELMER0_PORT3_MI1_ADDR 0x700004 +#define A_ELMER0_PORT3_MI1_DATA 0x700008 +#define A_ELMER0_PORT3_MI1_OP 0x70000c + +/* Simple bit definition for GPI and GP0 registers. */ +#define ELMER0_GP_BIT0 0x0001 +#define ELMER0_GP_BIT1 0x0002 +#define ELMER0_GP_BIT2 0x0004 +#define ELMER0_GP_BIT3 0x0008 +#define ELMER0_GP_BIT4 0x0010 +#define ELMER0_GP_BIT5 0x0020 +#define ELMER0_GP_BIT6 0x0040 +#define ELMER0_GP_BIT7 0x0080 +#define ELMER0_GP_BIT8 0x0100 +#define ELMER0_GP_BIT9 0x0200 +#define ELMER0_GP_BIT10 0x0400 +#define ELMER0_GP_BIT11 0x0800 +#define ELMER0_GP_BIT12 0x1000 +#define ELMER0_GP_BIT13 0x2000 +#define ELMER0_GP_BIT14 0x4000 +#define ELMER0_GP_BIT15 0x8000 +#define ELMER0_GP_BIT16 0x10000 +#define ELMER0_GP_BIT17 0x20000 +#define ELMER0_GP_BIT18 0x40000 +#define ELMER0_GP_BIT19 0x80000 + +#define MI1_OP_DIRECT_WRITE 1 +#define MI1_OP_DIRECT_READ 2 + +#define MI1_OP_INDIRECT_ADDRESS 0 +#define MI1_OP_INDIRECT_WRITE 1 +#define MI1_OP_INDIRECT_READ_INC 2 +#define MI1_OP_INDIRECT_READ 3 + +#endif /* _CXGB_ELMER0_H_ */ Index: drivers/net/chelsio/espi.c =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/espi.c (mode:100644) @@ -0,0 +1,346 @@ +/***************************************************************************** + * * + * File: espi.c * + * $Revision: 1.14 $ * + * $Date: 2005/05/14 00:59:32 $ * + * Description: * + * Ethernet SPI functionality. * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#include "common.h" +#include "regs.h" +#include "espi.h" + +struct peespi { + adapter_t *adapter; + struct espi_intr_counts intr_cnt; + u32 misc_ctrl; + spinlock_t lock; +}; + +#define ESPI_INTR_MASK (F_DIP4ERR | F_RXDROP | F_TXDROP | F_RXOVERFLOW | \ + F_RAMPARITYERR | F_DIP2PARITYERR) +#define MON_MASK (V_MONITORED_PORT_NUM(3) | F_MONITORED_DIRECTION \ + | F_MONITORED_INTERFACE) + +#define TRICN_CNFG 14 +#define TRICN_CMD_READ 0x11 +#define TRICN_CMD_WRITE 0x21 +#define TRICN_CMD_ATTEMPTS 10 + +static int tricn_write(adapter_t *adapter, int bundle_addr, int module_addr, + int ch_addr, int reg_offset, u32 wr_data) +{ + int busy, attempts = TRICN_CMD_ATTEMPTS; + + writel(V_WRITE_DATA(wr_data) | + V_REGISTER_OFFSET(reg_offset) | + V_CHANNEL_ADDR(ch_addr) | V_MODULE_ADDR(module_addr) | + V_BUNDLE_ADDR(bundle_addr) | + V_SPI4_COMMAND(TRICN_CMD_WRITE), + adapter->regs + A_ESPI_CMD_ADDR); + writel(0, adapter->regs + A_ESPI_GOSTAT); + + do { + busy = readl(adapter->regs + A_ESPI_GOSTAT) & F_ESPI_CMD_BUSY; + } while (busy && --attempts); + + if (busy) + CH_ERR("%s: TRICN write timed out\n", adapter->name); + + return busy; +} + +/* 1. Deassert rx_reset_core. */ +/* 2. Program TRICN_CNFG registers. */ +/* 3. Deassert rx_reset_link */ +static int tricn_init(adapter_t *adapter) +{ + int i = 0; + int sme = 1; + int stat = 0; + int timeout = 0; + int is_ready = 0; + int dynamic_deskew = 0; + + if (dynamic_deskew) + sme = 0; + + + /* 1 */ + timeout=1000; + do { + stat = readl(adapter->regs + A_ESPI_RX_RESET); + is_ready = (stat & 0x4); + timeout--; + udelay(5); + } while (!is_ready || (timeout==0)); + writel(0x2, adapter->regs + A_ESPI_RX_RESET); + if (timeout==0) + { + CH_ERR("ESPI : ERROR : Timeout tricn_init() \n"); + t1_fatal_err(adapter); + } + + /* 2 */ + if (sme) { + tricn_write(adapter, 0, 0, 0, TRICN_CNFG, 0x81); + tricn_write(adapter, 0, 1, 0, TRICN_CNFG, 0x81); + tricn_write(adapter, 0, 2, 0, TRICN_CNFG, 0x81); + } + for (i=1; i<= 8; i++) tricn_write(adapter, 0, 0, i, TRICN_CNFG, 0xf1); + for (i=1; i<= 2; i++) tricn_write(adapter, 0, 1, i, TRICN_CNFG, 0xf1); + for (i=1; i<= 3; i++) tricn_write(adapter, 0, 2, i, TRICN_CNFG, 0xe1); + for (i=4; i<= 4; i++) tricn_write(adapter, 0, 2, i, TRICN_CNFG, 0xf1); + for (i=5; i<= 5; i++) tricn_write(adapter, 0, 2, i, TRICN_CNFG, 0xe1); + for (i=6; i<= 6; i++) tricn_write(adapter, 0, 2, i, TRICN_CNFG, 0xf1); + for (i=7; i<= 7; i++) tricn_write(adapter, 0, 2, i, TRICN_CNFG, 0x80); + for (i=8; i<= 8; i++) tricn_write(adapter, 0, 2, i, TRICN_CNFG, 0xf1); + + /* 3 */ + writel(0x3, adapter->regs + A_ESPI_RX_RESET); + + return 0; +} + +void t1_espi_intr_enable(struct peespi *espi) +{ + u32 enable, pl_intr = readl(espi->adapter->regs + A_PL_ENABLE); + + /* + * Cannot enable ESPI interrupts on T1B because HW asserts the + * interrupt incorrectly, namely the driver gets ESPI interrupts + * but no data is actually dropped (can verify this reading the ESPI + * drop registers). Also, once the ESPI interrupt is asserted it + * cannot be cleared (HW bug). + */ + enable = t1_is_T1B(espi->adapter) ? 0 : ESPI_INTR_MASK; + writel(enable, espi->adapter->regs + A_ESPI_INTR_ENABLE); + writel(pl_intr | F_PL_INTR_ESPI, espi->adapter->regs + A_PL_ENABLE); +} + +void t1_espi_intr_clear(struct peespi *espi) +{ + writel(0xffffffff, espi->adapter->regs + A_ESPI_INTR_STATUS); + writel(F_PL_INTR_ESPI, espi->adapter->regs + A_PL_CAUSE); +} + +void t1_espi_intr_disable(struct peespi *espi) +{ + u32 pl_intr = readl(espi->adapter->regs + A_PL_ENABLE); + + writel(0, espi->adapter->regs + A_ESPI_INTR_ENABLE); + writel(pl_intr & ~F_PL_INTR_ESPI, espi->adapter->regs + A_PL_ENABLE); +} + +int t1_espi_intr_handler(struct peespi *espi) +{ + u32 cnt; + u32 status = readl(espi->adapter->regs + A_ESPI_INTR_STATUS); + + if (status & F_DIP4ERR) + espi->intr_cnt.DIP4_err++; + if (status & F_RXDROP) + espi->intr_cnt.rx_drops++; + if (status & F_TXDROP) + espi->intr_cnt.tx_drops++; + if (status & F_RXOVERFLOW) + espi->intr_cnt.rx_ovflw++; + if (status & F_RAMPARITYERR) + espi->intr_cnt.parity_err++; + if (status & F_DIP2PARITYERR) { + espi->intr_cnt.DIP2_parity_err++; + + /* + * Must read the error count to clear the interrupt + * that it causes. + */ + cnt = readl(espi->adapter->regs + A_ESPI_DIP2_ERR_COUNT); + } + + /* + * For T1B we need to write 1 to clear ESPI interrupts. For T2+ we + * write the status as is. + */ + if (status && t1_is_T1B(espi->adapter)) + status = 1; + writel(status, espi->adapter->regs + A_ESPI_INTR_STATUS); + return 0; +} + +const struct espi_intr_counts *t1_espi_get_intr_counts(struct peespi *espi) +{ + return &espi->intr_cnt; +} + +static void espi_setup_for_pm3393(adapter_t *adapter) +{ + u32 wmark = t1_is_T1B(adapter) ? 0x4000 : 0x3200; + + writel(0x1f4, adapter->regs + A_ESPI_SCH_TOKEN0); + writel(0x1f4, adapter->regs + A_ESPI_SCH_TOKEN1); + writel(0x1f4, adapter->regs + A_ESPI_SCH_TOKEN2); + writel(0x1f4, adapter->regs + A_ESPI_SCH_TOKEN3); + writel(0x100, adapter->regs + A_ESPI_RX_FIFO_ALMOST_EMPTY_WATERMARK); + writel(wmark, adapter->regs + A_ESPI_RX_FIFO_ALMOST_FULL_WATERMARK); + writel(3, adapter->regs + A_ESPI_CALENDAR_LENGTH); + writel(0x08000008, adapter->regs + A_ESPI_TRAIN); + writel(V_RX_NPORTS(1) | V_TX_NPORTS(1), adapter->regs + A_PORT_CONFIG); +} + +/* T2 Init part -- */ +/* 1. Set T_ESPI_MISCCTRL_ADDR */ +/* 2. Init ESPI registers. */ +/* 3. Init TriCN Hard Macro */ +int t1_espi_init(struct peespi *espi, int mac_type, int nports) +{ + u32 cnt; + + u32 status_enable_extra = 0; + adapter_t *adapter = espi->adapter; + u32 status, burstval = 0x800100; + + /* Disable ESPI training. MACs that can handle it enable it below. */ + writel(0, adapter->regs + A_ESPI_TRAIN); + + if (is_T2(adapter)) { + writel(V_OUT_OF_SYNC_COUNT(4) | + V_DIP2_PARITY_ERR_THRES(3) | + V_DIP4_THRES(1), adapter->regs + A_ESPI_MISC_CONTROL); + if (nports == 4) { + /* T204: maxburst1 = 0x40, maxburst2 = 0x20 */ + burstval = 0x200040; + } + } + writel(burstval, adapter->regs + A_ESPI_MAXBURST1_MAXBURST2); + + switch (mac_type) { + case CHBT_MAC_PM3393: + espi_setup_for_pm3393(adapter); + break; + default: + return -1; + } + + /* + * Make sure any pending interrupts from the SPI are + * Cleared before enabling the interrupt. + */ + writel(ESPI_INTR_MASK, espi->adapter->regs + A_ESPI_INTR_ENABLE); + status = readl(espi->adapter->regs + A_ESPI_INTR_STATUS); + if (status & F_DIP2PARITYERR) { + cnt = readl(espi->adapter->regs + A_ESPI_DIP2_ERR_COUNT); + } + + /* + * For T1B we need to write 1 to clear ESPI interrupts. For T2+ we + * write the status as is. + */ + if (status && t1_is_T1B(espi->adapter)) + status = 1; + writel(status, espi->adapter->regs + A_ESPI_INTR_STATUS); + + writel(status_enable_extra | F_RXSTATUSENABLE, + adapter->regs + A_ESPI_FIFO_STATUS_ENABLE); + + if (is_T2(adapter)) { + tricn_init(adapter); + /* + * Always position the control at the 1st port egress IN + * (sop,eop) counter to reduce PIOs for T/N210 workaround. + */ + espi->misc_ctrl = (readl(adapter->regs + A_ESPI_MISC_CONTROL) + & ~MON_MASK) | (F_MONITORED_DIRECTION + | F_MONITORED_INTERFACE); + writel(espi->misc_ctrl, adapter->regs + A_ESPI_MISC_CONTROL); + spin_lock_init(&espi->lock); + } + + return 0; +} + +void t1_espi_destroy(struct peespi *espi) +{ + kfree(espi); +} + +struct peespi *t1_espi_create(adapter_t *adapter) +{ + struct peespi *espi = kmalloc(sizeof(*espi), GFP_KERNEL); + + memset(espi, 0, sizeof(*espi)); + + if (espi) + espi->adapter = adapter; + return espi; +} + +void t1_espi_set_misc_ctrl(adapter_t *adapter, u32 val) +{ + struct peespi *espi = adapter->espi; + + if (!is_T2(adapter)) + return; + spin_lock(&espi->lock); + espi->misc_ctrl = (val & ~MON_MASK) | + (espi->misc_ctrl & MON_MASK); + writel(espi->misc_ctrl, adapter->regs + A_ESPI_MISC_CONTROL); + spin_unlock(&espi->lock); +} + +u32 t1_espi_get_mon(adapter_t *adapter, u32 addr, u8 wait) +{ + u32 sel; + + struct peespi *espi = adapter->espi; + + if (!is_T2(adapter)) + return 0; + sel = V_MONITORED_PORT_NUM((addr & 0x3c) >> 2); + if (!wait) { + if (!spin_trylock(&espi->lock)) + return 0; + } + else + spin_lock(&espi->lock); + if ((sel != (espi->misc_ctrl & MON_MASK))) { + writel(((espi->misc_ctrl & ~MON_MASK) | sel), + adapter->regs + A_ESPI_MISC_CONTROL); + sel = readl(adapter->regs + A_ESPI_SCH_TOKEN3); + writel(espi->misc_ctrl, adapter->regs + A_ESPI_MISC_CONTROL); + } + else + sel = readl(adapter->regs + A_ESPI_SCH_TOKEN3); + spin_unlock(&espi->lock); + return sel; +} Index: drivers/net/chelsio/espi.h =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/espi.h (mode:100644) @@ -0,0 +1,68 @@ +/***************************************************************************** + * * + * File: espi.h * + * $Revision: 1.7 $ * + * $Date: 2005/06/21 18:29:47 $ * + * Description: * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#ifndef _CXGB_ESPI_H_ +#define _CXGB_ESPI_H_ + +#include "common.h" + +struct espi_intr_counts { + unsigned int DIP4_err; + unsigned int rx_drops; + unsigned int tx_drops; + unsigned int rx_ovflw; + unsigned int parity_err; + unsigned int DIP2_parity_err; +}; + +struct peespi; + +struct peespi *t1_espi_create(adapter_t *adapter); +void t1_espi_destroy(struct peespi *espi); +int t1_espi_init(struct peespi *espi, int mac_type, int nports); + +void t1_espi_intr_enable(struct peespi *); +void t1_espi_intr_clear(struct peespi *); +void t1_espi_intr_disable(struct peespi *); +int t1_espi_intr_handler(struct peespi *); +const struct espi_intr_counts *t1_espi_get_intr_counts(struct peespi *espi); + +void t1_espi_set_misc_ctrl(adapter_t *adapter, u32 val); +u32 t1_espi_get_mon(adapter_t *adapter, u32 addr, u8 wait); + +#endif /* _CXGB_ESPI_H_ */ Index: drivers/net/chelsio/gmac.h =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/gmac.h (mode:100644) @@ -0,0 +1,134 @@ +/***************************************************************************** + * * + * File: gmac.h * + * $Revision: 1.6 $ * + * $Date: 2005/06/21 18:29:47 $ * + * Description: * + * Generic MAC functionality. * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#ifndef _CXGB_GMAC_H_ +#define _CXGB_GMAC_H_ + +#include "common.h" + +enum { MAC_STATS_UPDATE_FAST, MAC_STATS_UPDATE_FULL }; +enum { MAC_DIRECTION_RX = 1, MAC_DIRECTION_TX = 2 }; + +struct cmac_statistics { + /* Transmit */ + u64 TxOctetsOK; + u64 TxOctetsBad; + u64 TxUnicastFramesOK; + u64 TxMulticastFramesOK; + u64 TxBroadcastFramesOK; + u64 TxPauseFrames; + u64 TxFramesWithDeferredXmissions; + u64 TxLateCollisions; + u64 TxTotalCollisions; + u64 TxFramesAbortedDueToXSCollisions; + u64 TxUnderrun; + u64 TxLengthErrors; + u64 TxInternalMACXmitError; + u64 TxFramesWithExcessiveDeferral; + u64 TxFCSErrors; + + /* Receive */ + u64 RxOctetsOK; + u64 RxOctetsBad; + u64 RxUnicastFramesOK; + u64 RxMulticastFramesOK; + u64 RxBroadcastFramesOK; + u64 RxPauseFrames; + u64 RxFCSErrors; + u64 RxAlignErrors; + u64 RxSymbolErrors; + u64 RxDataErrors; + u64 RxSequenceErrors; + u64 RxRuntErrors; + u64 RxJabberErrors; + u64 RxInternalMACRcvError; + u64 RxInRangeLengthErrors; + u64 RxOutOfRangeLengthField; + u64 RxFrameTooLongErrors; +}; + +struct cmac_ops { + void (*destroy)(struct cmac *); + int (*reset)(struct cmac *); + int (*interrupt_enable)(struct cmac *); + int (*interrupt_disable)(struct cmac *); + int (*interrupt_clear)(struct cmac *); + int (*interrupt_handler)(struct cmac *); + + int (*enable)(struct cmac *, int); + int (*disable)(struct cmac *, int); + + int (*loopback_enable)(struct cmac *); + int (*loopback_disable)(struct cmac *); + + int (*set_mtu)(struct cmac *, int mtu); + int (*set_rx_mode)(struct cmac *, struct t1_rx_mode *rm); + + int (*set_speed_duplex_fc)(struct cmac *, int speed, int duplex, int fc); + int (*get_speed_duplex_fc)(struct cmac *, int *speed, int *duplex, + int *fc); + + const struct cmac_statistics *(*statistics_update)(struct cmac *, int); + + int (*macaddress_get)(struct cmac *, u8 mac_addr[6]); + int (*macaddress_set)(struct cmac *, u8 mac_addr[6]); +}; + +typedef struct _cmac_instance cmac_instance; + +struct cmac { + struct cmac_statistics stats; + adapter_t *adapter; + struct cmac_ops *ops; + cmac_instance *instance; +}; + +struct gmac { + unsigned int stats_update_period; + struct cmac *(*create)(adapter_t *adapter, int index); + int (*reset)(adapter_t *); +}; + +extern struct gmac t1_pm3393_ops; +extern struct gmac t1_chelsio_mac_ops; +extern struct gmac t1_vsc7321_ops; +extern struct gmac t1_ixf1010_ops; +extern struct gmac t1_dummy_mac_ops; + +#endif /* _CXGB_GMAC_H_ */ Index: drivers/net/chelsio/mv88x201x.c =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/mv88x201x.c (mode:100644) @@ -0,0 +1,252 @@ +/***************************************************************************** + * * + * File: mv88x201x.c * + * $Revision: 1.12 $ * + * $Date: 2005/04/15 19:27:14 $ * + * Description: * + * Marvell PHY (mv88x201x) functionality. * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#include "cphy.h" +#include "elmer0.h" + +/* + * The 88x2010 Rev C. requires some link status registers * to be read + * twice in order to get the right values. Future * revisions will fix + * this problem and then this macro * can disappear. + */ +#define MV88x2010_LINK_STATUS_BUGS 1 + +static int led_init(struct cphy *cphy) +{ + /* Setup the LED registers so we can turn on/off. + * Writing these bits maps control to another + * register. mmd(0x1) addr(0x7) + */ + mdio_write(cphy, 0x3, 0x8304, 0xdddd); + return 0; +} + +static int led_link(struct cphy *cphy, u32 do_enable) +{ + u32 led = 0; +#define LINK_ENABLE_BIT 0x1 + + mdio_read(cphy, 0x1, 0x7, &led); + + if (do_enable & LINK_ENABLE_BIT) { + led |= LINK_ENABLE_BIT; + mdio_write(cphy, 0x1, 0x7, led); + } else { + led &= ~LINK_ENABLE_BIT; + mdio_write(cphy, 0x1, 0x7, led); + } + return 0; +} + +/* Port Reset */ +static int mv88x201x_reset(struct cphy *cphy, int wait) +{ + /* This can be done through registers. It is not required since + * a full chip reset is used. + */ + return 0; +} + +static int mv88x201x_interrupt_enable(struct cphy *cphy) +{ + u32 elmer; + + /* Enable PHY LASI interrupts. */ + mdio_write(cphy, 0x1, 0x9002, 0x1); + + /* Enable Marvell interrupts through Elmer0. */ + t1_tpi_read(cphy->adapter, A_ELMER0_INT_ENABLE, &elmer); + elmer |= ELMER0_GP_BIT6; + t1_tpi_write(cphy->adapter, A_ELMER0_INT_ENABLE, elmer); + return 0; +} + +static int mv88x201x_interrupt_disable(struct cphy *cphy) +{ + u32 elmer; + + /* Disable PHY LASI interrupts. */ + mdio_write(cphy, 0x1, 0x9002, 0x0); + + /* Disable Marvell interrupts through Elmer0. */ + t1_tpi_read(cphy->adapter, A_ELMER0_INT_ENABLE, &elmer); + elmer &= ~ELMER0_GP_BIT6; + t1_tpi_write(cphy->adapter, A_ELMER0_INT_ENABLE, elmer); + return 0; +} + +static int mv88x201x_interrupt_clear(struct cphy *cphy) +{ + u32 elmer; + u32 val; + +#ifdef MV88x2010_LINK_STATUS_BUGS + /* Required to read twice before clear takes affect. */ + mdio_read(cphy, 0x1, 0x9003, &val); + mdio_read(cphy, 0x1, 0x9004, &val); + mdio_read(cphy, 0x1, 0x9005, &val); + + /* Read this register after the others above it else + * the register doesn't clear correctly. + */ + mdio_read(cphy, 0x1, 0x1, &val); +#endif + + /* Clear link status. */ + mdio_read(cphy, 0x1, 0x1, &val); + /* Clear PHY LASI interrupts. */ + mdio_read(cphy, 0x1, 0x9005, &val); + +#ifdef MV88x2010_LINK_STATUS_BUGS + /* Do it again. */ + mdio_read(cphy, 0x1, 0x9003, &val); + mdio_read(cphy, 0x1, 0x9004, &val); +#endif + + /* Clear Marvell interrupts through Elmer0. */ + t1_tpi_read(cphy->adapter, A_ELMER0_INT_CAUSE, &elmer); + elmer |= ELMER0_GP_BIT6; + t1_tpi_write(cphy->adapter, A_ELMER0_INT_CAUSE, elmer); + return 0; +} + +static int mv88x201x_interrupt_handler(struct cphy *cphy) +{ + /* Clear interrupts */ + mv88x201x_interrupt_clear(cphy); + + /* We have only enabled link change interrupts and so + * cphy_cause must be a link change interrupt. + */ + return cphy_cause_link_change; +} + +static int mv88x201x_set_loopback(struct cphy *cphy, int on) +{ + return 0; +} + +static int mv88x201x_get_link_status(struct cphy *cphy, int *link_ok, + int *speed, int *duplex, int *fc) +{ + u32 val = 0; +#define LINK_STATUS_BIT 0x4 + + if (link_ok) { + /* Read link status. */ + mdio_read(cphy, 0x1, 0x1, &val); + val &= LINK_STATUS_BIT; + *link_ok = (val == LINK_STATUS_BIT); + /* Turn on/off Link LED */ + led_link(cphy, *link_ok); + } + if (speed) + *speed = SPEED_10000; + if (duplex) + *duplex = DUPLEX_FULL; + if (fc) + *fc = PAUSE_RX | PAUSE_TX; + return 0; +} + +static void mv88x201x_destroy(struct cphy *cphy) +{ + kfree(cphy); +} + +static struct cphy_ops mv88x201x_ops = { + .destroy = mv88x201x_destroy, + .reset = mv88x201x_reset, + .interrupt_enable = mv88x201x_interrupt_enable, + .interrupt_disable = mv88x201x_interrupt_disable, + .interrupt_clear = mv88x201x_interrupt_clear, + .interrupt_handler = mv88x201x_interrupt_handler, + .get_link_status = mv88x201x_get_link_status, + .set_loopback = mv88x201x_set_loopback, +}; + +static struct cphy *mv88x201x_phy_create(adapter_t *adapter, int phy_addr, + struct mdio_ops *mdio_ops) +{ + u32 val; + struct cphy *cphy = kmalloc(sizeof(*cphy), GFP_KERNEL); + + if (!cphy) + return NULL; + memset(cphy, 0, sizeof(*cphy)); + cphy_init(cphy, adapter, phy_addr, &mv88x201x_ops, mdio_ops); + + /* Commands the PHY to enable XFP's clock. */ + mdio_read(cphy, 0x3, 0x8300, &val); + mdio_write(cphy, 0x3, 0x8300, val | 1); + + /* Clear link status. Required because of a bug in the PHY. */ + mdio_read(cphy, 0x1, 0x8, &val); + mdio_read(cphy, 0x3, 0x8, &val); + + /* Allows for Link,Ack LED turn on/off */ + led_init(cphy); + return cphy; +} + +/* Chip Reset */ +static int mv88x201x_phy_reset(adapter_t *adapter) +{ + u32 val; + + t1_tpi_read(adapter, A_ELMER0_GPO, &val); + val &= ~4; + t1_tpi_write(adapter, A_ELMER0_GPO, val); + msleep(100); + + t1_tpi_write(adapter, A_ELMER0_GPO, val | 4); + msleep(1000); + + /* Now lets enable the Laser. Delay 100us */ + t1_tpi_read(adapter, A_ELMER0_GPO, &val); + val |= 0x8000; + t1_tpi_write(adapter, A_ELMER0_GPO, val); + udelay(100); + return 0; +} + +struct gphy t1_mv88x201x_ops = { + mv88x201x_phy_create, + mv88x201x_phy_reset +}; Index: drivers/net/chelsio/pm3393.c =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/pm3393.c (mode:100644) @@ -0,0 +1,826 @@ +/***************************************************************************** + * * + * File: pm3393.c * + * $Revision: 1.16 $ * + * $Date: 2005/05/14 00:59:32 $ * + * Description: * + * PMC/SIERRA (pm3393) MAC-PHY functionality. * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#include "common.h" +#include "regs.h" +#include "gmac.h" +#include "elmer0.h" +#include "suni1x10gexp_regs.h" + +/* 802.3ae 10Gb/s MDIO Manageable Device(MMD) + */ +enum { + MMD_RESERVED, + MMD_PMAPMD, + MMD_WIS, + MMD_PCS, + MMD_PHY_XGXS, /* XGMII Extender Sublayer */ + MMD_DTE_XGXS, +}; + +enum { + PHY_XGXS_CTRL_1, + PHY_XGXS_STATUS_1 +}; + +#define OFFSET(REG_ADDR) (REG_ADDR << 2) + +/* Max frame size PM3393 can handle. Includes Ethernet header and CRC. */ +#define MAX_FRAME_SIZE 9600 + +#define IPG 12 +#define TXXG_CONF1_VAL ((IPG << SUNI1x10GEXP_BITOFF_TXXG_IPGT) | \ + SUNI1x10GEXP_BITMSK_TXXG_32BIT_ALIGN | SUNI1x10GEXP_BITMSK_TXXG_CRCEN | \ + SUNI1x10GEXP_BITMSK_TXXG_PADEN) +#define RXXG_CONF1_VAL (SUNI1x10GEXP_BITMSK_RXXG_PUREP | 0x14 | \ + SUNI1x10GEXP_BITMSK_RXXG_FLCHK | SUNI1x10GEXP_BITMSK_RXXG_CRC_STRIP) + +/* Update statistics every 15 minutes */ +#define STATS_TICK_SECS (15 * 60) + +enum { /* RMON registers */ + RxOctetsReceivedOK = SUNI1x10GEXP_REG_MSTAT_COUNTER_1_LOW, + RxUnicastFramesReceivedOK = SUNI1x10GEXP_REG_MSTAT_COUNTER_4_LOW, + RxMulticastFramesReceivedOK = SUNI1x10GEXP_REG_MSTAT_COUNTER_5_LOW, + RxBroadcastFramesReceivedOK = SUNI1x10GEXP_REG_MSTAT_COUNTER_6_LOW, + RxPAUSEMACCtrlFramesReceived = SUNI1x10GEXP_REG_MSTAT_COUNTER_8_LOW, + RxFrameCheckSequenceErrors = SUNI1x10GEXP_REG_MSTAT_COUNTER_10_LOW, + RxFramesLostDueToInternalMACErrors = SUNI1x10GEXP_REG_MSTAT_COUNTER_11_LOW, + RxSymbolErrors = SUNI1x10GEXP_REG_MSTAT_COUNTER_12_LOW, + RxInRangeLengthErrors = SUNI1x10GEXP_REG_MSTAT_COUNTER_13_LOW, + RxFramesTooLongErrors = SUNI1x10GEXP_REG_MSTAT_COUNTER_15_LOW, + RxJabbers = SUNI1x10GEXP_REG_MSTAT_COUNTER_16_LOW, + RxFragments = SUNI1x10GEXP_REG_MSTAT_COUNTER_17_LOW, + RxUndersizedFrames = SUNI1x10GEXP_REG_MSTAT_COUNTER_18_LOW, + + TxOctetsTransmittedOK = SUNI1x10GEXP_REG_MSTAT_COUNTER_33_LOW, + TxFramesLostDueToInternalMACTransmissionError = SUNI1x10GEXP_REG_MSTAT_COUNTER_35_LOW, + TxTransmitSystemError = SUNI1x10GEXP_REG_MSTAT_COUNTER_36_LOW, + TxUnicastFramesTransmittedOK = SUNI1x10GEXP_REG_MSTAT_COUNTER_38_LOW, + TxMulticastFramesTransmittedOK = SUNI1x10GEXP_REG_MSTAT_COUNTER_40_LOW, + TxBroadcastFramesTransmittedOK = SUNI1x10GEXP_REG_MSTAT_COUNTER_42_LOW, + TxPAUSEMACCtrlFramesTransmitted = SUNI1x10GEXP_REG_MSTAT_COUNTER_43_LOW +}; + +struct _cmac_instance { + u8 enabled; + u8 fc; + u8 mac_addr[6]; +}; + +static int pmread(struct cmac *cmac, u32 reg, u32 * data32) +{ + t1_tpi_read(cmac->adapter, OFFSET(reg), data32); + return 0; +} + +static int pmwrite(struct cmac *cmac, u32 reg, u32 data32) +{ + t1_tpi_write(cmac->adapter, OFFSET(reg), data32); + return 0; +} + +/* Port reset. */ +static int pm3393_reset(struct cmac *cmac) +{ + return 0; +} + +/* + * Enable interrupts for the PM3393 + + 1. Enable PM3393 BLOCK interrupts. + 2. Enable PM3393 Master Interrupt bit(INTE) + 3. Enable ELMER's PM3393 bit. + 4. Enable Terminator external interrupt. +*/ +static int pm3393_interrupt_enable(struct cmac *cmac) +{ + u32 pl_intr; + + /* PM3393 - Enabling all hardware block interrupts. + */ + pmwrite(cmac, SUNI1x10GEXP_REG_SERDES_3125_INTERRUPT_ENABLE, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_XRF_INTERRUPT_ENABLE, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_XRF_DIAG_INTERRUPT_ENABLE, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_RXOAM_INTERRUPT_ENABLE, 0xffff); + + /* Don't interrupt on statistics overflow, we are polling */ + pmwrite(cmac, SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_0, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_1, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_2, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_3, 0); + + pmwrite(cmac, SUNI1x10GEXP_REG_IFLX_FIFO_OVERFLOW_ENABLE, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_PL4ODP_INTERRUPT_MASK, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_XTEF_INTERRUPT_ENABLE, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_TXOAM_INTERRUPT_ENABLE, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_CONFIG_3, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_PL4IO_LOCK_DETECT_MASK, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_TXXG_CONFIG_3, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_PL4IDU_INTERRUPT_MASK, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_EFLX_FIFO_OVERFLOW_ERROR_ENABLE, 0xffff); + + /* PM3393 - Global interrupt enable + */ + /* TBD XXX Disable for now until we figure out why error interrupts keep asserting. */ + pmwrite(cmac, SUNI1x10GEXP_REG_GLOBAL_INTERRUPT_ENABLE, + 0 /*SUNI1x10GEXP_BITMSK_TOP_INTE */ ); + + /* TERMINATOR - PL_INTERUPTS_EXT */ + pl_intr = readl(cmac->adapter->regs + A_PL_ENABLE); + pl_intr |= F_PL_INTR_EXT; + writel(pl_intr, cmac->adapter->regs + A_PL_ENABLE); + return 0; +} + +static int pm3393_interrupt_disable(struct cmac *cmac) +{ + u32 elmer; + + /* PM3393 - Enabling HW interrupt blocks. */ + pmwrite(cmac, SUNI1x10GEXP_REG_SERDES_3125_INTERRUPT_ENABLE, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_XRF_INTERRUPT_ENABLE, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_XRF_DIAG_INTERRUPT_ENABLE, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_RXOAM_INTERRUPT_ENABLE, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_0, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_1, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_2, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_3, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_IFLX_FIFO_OVERFLOW_ENABLE, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_PL4ODP_INTERRUPT_MASK, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_XTEF_INTERRUPT_ENABLE, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_TXOAM_INTERRUPT_ENABLE, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_CONFIG_3, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_PL4IO_LOCK_DETECT_MASK, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_TXXG_CONFIG_3, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_PL4IDU_INTERRUPT_MASK, 0); + pmwrite(cmac, SUNI1x10GEXP_REG_EFLX_FIFO_OVERFLOW_ERROR_ENABLE, 0); + + /* PM3393 - Global interrupt enable */ + pmwrite(cmac, SUNI1x10GEXP_REG_GLOBAL_INTERRUPT_ENABLE, 0); + + /* ELMER - External chip interrupts. */ + t1_tpi_read(cmac->adapter, A_ELMER0_INT_ENABLE, &elmer); + elmer &= ~ELMER0_GP_BIT1; + t1_tpi_write(cmac->adapter, A_ELMER0_INT_ENABLE, elmer); + + /* TERMINATOR - PL_INTERUPTS_EXT */ + /* DO NOT DISABLE TERMINATOR's EXTERNAL INTERRUPTS. ANOTHER CHIP + * COULD WANT THEM ENABLED. We disable PM3393 at the ELMER level. + */ + + return 0; +} + +static int pm3393_interrupt_clear(struct cmac *cmac) +{ + u32 elmer; + u32 pl_intr; + u32 val32; + + /* PM3393 - Clearing HW interrupt blocks. Note, this assumes + * bit WCIMODE=0 for a clear-on-read. + */ + pmread(cmac, SUNI1x10GEXP_REG_SERDES_3125_INTERRUPT_STATUS, &val32); + pmread(cmac, SUNI1x10GEXP_REG_XRF_INTERRUPT_STATUS, &val32); + pmread(cmac, SUNI1x10GEXP_REG_XRF_DIAG_INTERRUPT_STATUS, &val32); + pmread(cmac, SUNI1x10GEXP_REG_RXOAM_INTERRUPT_STATUS, &val32); + pmread(cmac, SUNI1x10GEXP_REG_PL4ODP_INTERRUPT, &val32); + pmread(cmac, SUNI1x10GEXP_REG_XTEF_INTERRUPT_STATUS, &val32); + pmread(cmac, SUNI1x10GEXP_REG_IFLX_FIFO_OVERFLOW_INTERRUPT, &val32); + pmread(cmac, SUNI1x10GEXP_REG_TXOAM_INTERRUPT_STATUS, &val32); + pmread(cmac, SUNI1x10GEXP_REG_RXXG_INTERRUPT, &val32); + pmread(cmac, SUNI1x10GEXP_REG_TXXG_INTERRUPT, &val32); + pmread(cmac, SUNI1x10GEXP_REG_PL4IDU_INTERRUPT, &val32); + pmread(cmac, SUNI1x10GEXP_REG_EFLX_FIFO_OVERFLOW_ERROR_INDICATION, + &val32); + pmread(cmac, SUNI1x10GEXP_REG_PL4IO_LOCK_DETECT_STATUS, &val32); + pmread(cmac, SUNI1x10GEXP_REG_PL4IO_LOCK_DETECT_CHANGE, &val32); + + /* PM3393 - Global interrupt status + */ + pmread(cmac, SUNI1x10GEXP_REG_MASTER_INTERRUPT_STATUS, &val32); + + /* ELMER - External chip interrupts. + */ + t1_tpi_read(cmac->adapter, A_ELMER0_INT_CAUSE, &elmer); + elmer |= ELMER0_GP_BIT1; + t1_tpi_write(cmac->adapter, A_ELMER0_INT_CAUSE, elmer); + + /* TERMINATOR - PL_INTERUPTS_EXT + */ + pl_intr = readl(cmac->adapter->regs + A_PL_CAUSE); + pl_intr |= F_PL_INTR_EXT; + writel(pl_intr, cmac->adapter->regs + A_PL_CAUSE); + + return 0; +} + +/* Interrupt handler */ +static int pm3393_interrupt_handler(struct cmac *cmac) +{ + u32 master_intr_status; +/* + 1. Read master interrupt register. + 2. Read BLOCK's interrupt status registers. + 3. Handle BLOCK interrupts. +*/ + /* Read the master interrupt status register. */ + pmread(cmac, SUNI1x10GEXP_REG_MASTER_INTERRUPT_STATUS, + &master_intr_status); + + /* TBD XXX Lets just clear everything for now */ + pm3393_interrupt_clear(cmac); + + return 0; +} + +static int pm3393_enable(struct cmac *cmac, int which) +{ + if (which & MAC_DIRECTION_RX) + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_CONFIG_1, + (RXXG_CONF1_VAL | SUNI1x10GEXP_BITMSK_RXXG_RXEN)); + + if (which & MAC_DIRECTION_TX) { + u32 val = TXXG_CONF1_VAL | SUNI1x10GEXP_BITMSK_TXXG_TXEN0; + + if (cmac->instance->fc & PAUSE_RX) + val |= SUNI1x10GEXP_BITMSK_TXXG_FCRX; + if (cmac->instance->fc & PAUSE_TX) + val |= SUNI1x10GEXP_BITMSK_TXXG_FCTX; + pmwrite(cmac, SUNI1x10GEXP_REG_TXXG_CONFIG_1, val); + } + + cmac->instance->enabled |= which; + return 0; +} + +static int pm3393_enable_port(struct cmac *cmac, int which) +{ + /* Clear port statistics */ + pmwrite(cmac, SUNI1x10GEXP_REG_MSTAT_CONTROL, + SUNI1x10GEXP_BITMSK_MSTAT_CLEAR); + udelay(2); + memset(&cmac->stats, 0, sizeof(struct cmac_statistics)); + + pm3393_enable(cmac, which); + + /* + * XXX This should be done by the PHY and preferrably not at all. + * The PHY doesn't give us link status indication on its own so have + * the link management code query it instead. + */ + { + extern void link_changed(adapter_t *adapter, int port_id); + + link_changed(cmac->adapter, 0); + } + return 0; +} + +static int pm3393_disable(struct cmac *cmac, int which) +{ + if (which & MAC_DIRECTION_RX) + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_CONFIG_1, RXXG_CONF1_VAL); + if (which & MAC_DIRECTION_TX) + pmwrite(cmac, SUNI1x10GEXP_REG_TXXG_CONFIG_1, TXXG_CONF1_VAL); + + /* + * The disable is graceful. Give the PM3393 time. Can't wait very + * long here, we may be holding locks. + */ + udelay(20); + + cmac->instance->enabled &= ~which; + return 0; +} + +static int pm3393_loopback_enable(struct cmac *cmac) +{ + return 0; +} + +static int pm3393_loopback_disable(struct cmac *cmac) +{ + return 0; +} + +static int pm3393_set_mtu(struct cmac *cmac, int mtu) +{ + int enabled = cmac->instance->enabled; + + /* MAX_FRAME_SIZE includes header + FCS, mtu doesn't */ + mtu += 14 + 4; + if (mtu > MAX_FRAME_SIZE) + return -EINVAL; + + /* Disable Rx/Tx MAC before configuring it. */ + if (enabled) + pm3393_disable(cmac, MAC_DIRECTION_RX | MAC_DIRECTION_TX); + + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_MAX_FRAME_LENGTH, mtu); + pmwrite(cmac, SUNI1x10GEXP_REG_TXXG_MAX_FRAME_SIZE, mtu); + + if (enabled) + pm3393_enable(cmac, enabled); + return 0; +} + +static u32 calc_crc(u8 *b, int len) +{ + int i; + u32 crc = (u32)~0; + + /* calculate crc one bit at a time */ + while (len--) { + crc ^= *b++; + for (i = 0; i < 8; i++) { + if (crc & 0x1) + crc = (crc >> 1) ^ 0xedb88320; + else + crc = (crc >> 1); + } + } + + /* reverse bits */ + crc = ((crc >> 4) & 0x0f0f0f0f) | ((crc << 4) & 0xf0f0f0f0); + crc = ((crc >> 2) & 0x33333333) | ((crc << 2) & 0xcccccccc); + crc = ((crc >> 1) & 0x55555555) | ((crc << 1) & 0xaaaaaaaa); + /* swap bytes */ + crc = (crc >> 16) | (crc << 16); + crc = (crc >> 8 & 0x00ff00ff) | (crc << 8 & 0xff00ff00); + + return crc; +} + +static int pm3393_set_rx_mode(struct cmac *cmac, struct t1_rx_mode *rm) +{ + int enabled = cmac->instance->enabled & MAC_DIRECTION_RX; + u32 rx_mode; + + /* Disable MAC RX before reconfiguring it */ + if (enabled) + pm3393_disable(cmac, MAC_DIRECTION_RX); + + pmread(cmac, SUNI1x10GEXP_REG_RXXG_ADDRESS_FILTER_CONTROL_2, &rx_mode); + rx_mode &= ~(SUNI1x10GEXP_BITMSK_RXXG_PMODE | + SUNI1x10GEXP_BITMSK_RXXG_MHASH_EN); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_ADDRESS_FILTER_CONTROL_2, + (u16)rx_mode); + + if (t1_rx_mode_promisc(rm)) { + /* Promiscuous mode. */ + rx_mode |= SUNI1x10GEXP_BITMSK_RXXG_PMODE; + } + if (t1_rx_mode_allmulti(rm)) { + /* Accept all multicast. */ + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_LOW, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_MIDLOW, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_MIDHIGH, 0xffff); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_HIGH, 0xffff); + rx_mode |= SUNI1x10GEXP_BITMSK_RXXG_MHASH_EN; + } else if (t1_rx_mode_mc_cnt(rm)) { + /* Accept one or more multicast(s). */ + u8 *addr; + int bit; + u16 mc_filter[4] = { 0, }; + + while ((addr = t1_get_next_mcaddr(rm))) { + bit = (calc_crc(addr, ETH_ALEN) >> 23) & 0x3f; /* bit[23:28] */ + mc_filter[bit >> 4] |= 1 << (bit & 0xf); + } + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_LOW, mc_filter[0]); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_MIDLOW, mc_filter[1]); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_MIDHIGH, mc_filter[2]); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_HIGH, mc_filter[3]); + rx_mode |= SUNI1x10GEXP_BITMSK_RXXG_MHASH_EN; + } + + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_ADDRESS_FILTER_CONTROL_2, (u16)rx_mode); + + if (enabled) + pm3393_enable(cmac, MAC_DIRECTION_RX); + + return 0; +} + +static int pm3393_get_speed_duplex_fc(struct cmac *cmac, int *speed, + int *duplex, int *fc) +{ + if (speed) + *speed = SPEED_10000; + if (duplex) + *duplex = DUPLEX_FULL; + if (fc) + *fc = cmac->instance->fc; + return 0; +} + +static int pm3393_set_speed_duplex_fc(struct cmac *cmac, int speed, int duplex, + int fc) +{ + if (speed >= 0 && speed != SPEED_10000) + return -1; + if (duplex >= 0 && duplex != DUPLEX_FULL) + return -1; + if (fc & ~(PAUSE_TX | PAUSE_RX)) + return -1; + + if (fc != cmac->instance->fc) { + cmac->instance->fc = (u8) fc; + if (cmac->instance->enabled & MAC_DIRECTION_TX) + pm3393_enable(cmac, MAC_DIRECTION_TX); + } + return 0; +} + +#define RMON_UPDATE(mac, name, stat_name) \ + { \ + t1_tpi_read((mac)->adapter, OFFSET(name), &val0); \ + t1_tpi_read((mac)->adapter, OFFSET(((name)+1)), &val1); \ + t1_tpi_read((mac)->adapter, OFFSET(((name)+2)), &val2); \ + (mac)->stats.stat_name = ((u64)val0 & 0xffff) | \ + (((u64)val1 & 0xffff) << 16) | \ + (((u64)val2 & 0xff) << 32) | \ + ((mac)->stats.stat_name & \ + (~(u64)0 << 40)); \ + if (ro & \ + ((name - SUNI1x10GEXP_REG_MSTAT_COUNTER_0_LOW) >> 2)) \ + (mac)->stats.stat_name += ((u64)1 << 40); \ + } + +static const struct cmac_statistics *pm3393_update_statistics(struct cmac *mac, + int flag) +{ + u64 ro; + u32 val0, val1, val2, val3; + + /* Snap the counters */ + pmwrite(mac, SUNI1x10GEXP_REG_MSTAT_CONTROL, + SUNI1x10GEXP_BITMSK_MSTAT_SNAP); + + /* Counter rollover, clear on read */ + pmread(mac, SUNI1x10GEXP_REG_MSTAT_COUNTER_ROLLOVER_0, &val0); + pmread(mac, SUNI1x10GEXP_REG_MSTAT_COUNTER_ROLLOVER_1, &val1); + pmread(mac, SUNI1x10GEXP_REG_MSTAT_COUNTER_ROLLOVER_2, &val2); + pmread(mac, SUNI1x10GEXP_REG_MSTAT_COUNTER_ROLLOVER_3, &val3); + ro = ((u64)val0 & 0xffff) | (((u64)val1 & 0xffff) << 16) | + (((u64)val2 & 0xffff) << 32) | (((u64)val3 & 0xffff) << 48); + + /* Rx stats */ + RMON_UPDATE(mac, RxOctetsReceivedOK, RxOctetsOK); + RMON_UPDATE(mac, RxUnicastFramesReceivedOK, RxUnicastFramesOK); + RMON_UPDATE(mac, RxMulticastFramesReceivedOK, RxMulticastFramesOK); + RMON_UPDATE(mac, RxBroadcastFramesReceivedOK, RxBroadcastFramesOK); + RMON_UPDATE(mac, RxPAUSEMACCtrlFramesReceived, RxPauseFrames); + RMON_UPDATE(mac, RxFrameCheckSequenceErrors, RxFCSErrors); + RMON_UPDATE(mac, RxFramesLostDueToInternalMACErrors, + RxInternalMACRcvError); + RMON_UPDATE(mac, RxSymbolErrors, RxSymbolErrors); + RMON_UPDATE(mac, RxInRangeLengthErrors, RxInRangeLengthErrors); + RMON_UPDATE(mac, RxFramesTooLongErrors , RxFrameTooLongErrors); + RMON_UPDATE(mac, RxJabbers, RxJabberErrors); + RMON_UPDATE(mac, RxFragments, RxRuntErrors); + RMON_UPDATE(mac, RxUndersizedFrames, RxRuntErrors); + + /* Tx stats */ + RMON_UPDATE(mac, TxOctetsTransmittedOK, TxOctetsOK); + RMON_UPDATE(mac, TxFramesLostDueToInternalMACTransmissionError, + TxInternalMACXmitError); + RMON_UPDATE(mac, TxTransmitSystemError, TxFCSErrors); + RMON_UPDATE(mac, TxUnicastFramesTransmittedOK, TxUnicastFramesOK); + RMON_UPDATE(mac, TxMulticastFramesTransmittedOK, TxMulticastFramesOK); + RMON_UPDATE(mac, TxBroadcastFramesTransmittedOK, TxBroadcastFramesOK); + RMON_UPDATE(mac, TxPAUSEMACCtrlFramesTransmitted, TxPauseFrames); + + return &mac->stats; +} + +static int pm3393_macaddress_get(struct cmac *cmac, u8 mac_addr[6]) +{ + memcpy(mac_addr, cmac->instance->mac_addr, 6); + return 0; +} + +static int pm3393_macaddress_set(struct cmac *cmac, u8 ma[6]) +{ + u32 val, lo, mid, hi, enabled = cmac->instance->enabled; + + /* + * MAC addr: 00:07:43:00:13:09 + * + * ma[5] = 0x09 + * ma[4] = 0x13 + * ma[3] = 0x00 + * ma[2] = 0x43 + * ma[1] = 0x07 + * ma[0] = 0x00 + * + * The PM3393 requires byte swapping and reverse order entry + * when programming MAC addresses: + * + * low_bits[15:0] = ma[1]:ma[0] + * mid_bits[31:16] = ma[3]:ma[2] + * high_bits[47:32] = ma[5]:ma[4] + */ + + /* Store local copy */ + memcpy(cmac->instance->mac_addr, ma, 6); + + lo = ((u32) ma[1] << 8) | (u32) ma[0]; + mid = ((u32) ma[3] << 8) | (u32) ma[2]; + hi = ((u32) ma[5] << 8) | (u32) ma[4]; + + /* Disable Rx/Tx MAC before configuring it. */ + if (enabled) + pm3393_disable(cmac, MAC_DIRECTION_RX | MAC_DIRECTION_TX); + + /* Set RXXG Station Address */ + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_SA_15_0, lo); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_SA_31_16, mid); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_SA_47_32, hi); + + /* Set TXXG Station Address */ + pmwrite(cmac, SUNI1x10GEXP_REG_TXXG_SA_15_0, lo); + pmwrite(cmac, SUNI1x10GEXP_REG_TXXG_SA_31_16, mid); + pmwrite(cmac, SUNI1x10GEXP_REG_TXXG_SA_47_32, hi); + + /* Setup Exact Match Filter 1 with our MAC address + * + * Must disable exact match filter before configuring it. + */ + pmread(cmac, SUNI1x10GEXP_REG_RXXG_ADDRESS_FILTER_CONTROL_0, &val); + val &= 0xff0f; + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_ADDRESS_FILTER_CONTROL_0, val); + + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_EXACT_MATCH_ADDR_1_LOW, lo); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_EXACT_MATCH_ADDR_1_MID, mid); + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_EXACT_MATCH_ADDR_1_HIGH, hi); + + val |= 0x0090; + pmwrite(cmac, SUNI1x10GEXP_REG_RXXG_ADDRESS_FILTER_CONTROL_0, val); + + if (enabled) + pm3393_enable(cmac, enabled); + return 0; +} + +static void pm3393_destroy(struct cmac *cmac) +{ + kfree(cmac); +} + +static struct cmac_ops pm3393_ops = { + .destroy = pm3393_destroy, + .reset = pm3393_reset, + .interrupt_enable = pm3393_interrupt_enable, + .interrupt_disable = pm3393_interrupt_disable, + .interrupt_clear = pm3393_interrupt_clear, + .interrupt_handler = pm3393_interrupt_handler, + .enable = pm3393_enable_port, + .disable = pm3393_disable, + .loopback_enable = pm3393_loopback_enable, + .loopback_disable = pm3393_loopback_disable, + .set_mtu = pm3393_set_mtu, + .set_rx_mode = pm3393_set_rx_mode, + .get_speed_duplex_fc = pm3393_get_speed_duplex_fc, + .set_speed_duplex_fc = pm3393_set_speed_duplex_fc, + .statistics_update = pm3393_update_statistics, + .macaddress_get = pm3393_macaddress_get, + .macaddress_set = pm3393_macaddress_set +}; + +static struct cmac *pm3393_mac_create(adapter_t *adapter, int index) +{ + struct cmac *cmac; + + cmac = kmalloc(sizeof(*cmac) + sizeof(cmac_instance), GFP_KERNEL); + if (!cmac) + return NULL; + memset(cmac, 0, sizeof(*cmac)); + + cmac->ops = &pm3393_ops; + cmac->instance = (cmac_instance *) (cmac + 1); + cmac->adapter = adapter; + cmac->instance->fc = PAUSE_TX | PAUSE_RX; + + t1_tpi_write(adapter, OFFSET(0x0001), 0x00008000); + t1_tpi_write(adapter, OFFSET(0x0001), 0x00000000); + t1_tpi_write(adapter, OFFSET(0x2308), 0x00009800); + t1_tpi_write(adapter, OFFSET(0x2305), 0x00001001); /* PL4IO Enable */ + t1_tpi_write(adapter, OFFSET(0x2320), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x2321), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x2322), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x2323), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x2324), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x2325), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x2326), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x2327), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x2328), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x2329), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x232a), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x232b), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x232c), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x232d), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x232e), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x232f), 0x00008800); + t1_tpi_write(adapter, OFFSET(0x230d), 0x00009c00); + t1_tpi_write(adapter, OFFSET(0x2304), 0x00000202); /* PL4IO Calendar Repetitions */ + + t1_tpi_write(adapter, OFFSET(0x3200), 0x00008080); /* EFLX Enable */ + t1_tpi_write(adapter, OFFSET(0x3210), 0x00000000); /* EFLX Channel Deprovision */ + t1_tpi_write(adapter, OFFSET(0x3203), 0x00000000); /* EFLX Low Limit */ + t1_tpi_write(adapter, OFFSET(0x3204), 0x00000040); /* EFLX High Limit */ + t1_tpi_write(adapter, OFFSET(0x3205), 0x000002cc); /* EFLX Almost Full */ + t1_tpi_write(adapter, OFFSET(0x3206), 0x00000199); /* EFLX Almost Empty */ + t1_tpi_write(adapter, OFFSET(0x3207), 0x00000240); /* EFLX Cut Through Threshold */ + t1_tpi_write(adapter, OFFSET(0x3202), 0x00000000); /* EFLX Indirect Register Update */ + t1_tpi_write(adapter, OFFSET(0x3210), 0x00000001); /* EFLX Channel Provision */ + t1_tpi_write(adapter, OFFSET(0x3208), 0x0000ffff); /* EFLX Undocumented */ + t1_tpi_write(adapter, OFFSET(0x320a), 0x0000ffff); /* EFLX Undocumented */ + t1_tpi_write(adapter, OFFSET(0x320c), 0x0000ffff); /* EFLX enable overflow interrupt The other bit are undocumented */ + t1_tpi_write(adapter, OFFSET(0x320e), 0x0000ffff); /* EFLX Undocumented */ + + t1_tpi_write(adapter, OFFSET(0x2200), 0x0000c000); /* IFLX Configuration - enable */ + t1_tpi_write(adapter, OFFSET(0x2201), 0x00000000); /* IFLX Channel Deprovision */ + t1_tpi_write(adapter, OFFSET(0x220e), 0x00000000); /* IFLX Low Limit */ + t1_tpi_write(adapter, OFFSET(0x220f), 0x00000100); /* IFLX High Limit */ + t1_tpi_write(adapter, OFFSET(0x2210), 0x00000c00); /* IFLX Almost Full Limit */ + t1_tpi_write(adapter, OFFSET(0x2211), 0x00000599); /* IFLX Almost Empty Limit */ + t1_tpi_write(adapter, OFFSET(0x220d), 0x00000000); /* IFLX Indirect Register Update */ + t1_tpi_write(adapter, OFFSET(0x2201), 0x00000001); /* IFLX Channel Provision */ + t1_tpi_write(adapter, OFFSET(0x2203), 0x0000ffff); /* IFLX Undocumented */ + t1_tpi_write(adapter, OFFSET(0x2205), 0x0000ffff); /* IFLX Undocumented */ + t1_tpi_write(adapter, OFFSET(0x2209), 0x0000ffff); /* IFLX Enable overflow interrupt. The other bit are undocumented */ + + t1_tpi_write(adapter, OFFSET(0x2241), 0xfffffffe); /* PL4MOS Undocumented */ + t1_tpi_write(adapter, OFFSET(0x2242), 0x0000ffff); /* PL4MOS Undocumented */ + t1_tpi_write(adapter, OFFSET(0x2243), 0x00000008); /* PL4MOS Starving Burst Size */ + t1_tpi_write(adapter, OFFSET(0x2244), 0x00000008); /* PL4MOS Hungry Burst Size */ + t1_tpi_write(adapter, OFFSET(0x2245), 0x00000008); /* PL4MOS Transfer Size */ + t1_tpi_write(adapter, OFFSET(0x2240), 0x00000005); /* PL4MOS Disable */ + + t1_tpi_write(adapter, OFFSET(0x2280), 0x00002103); /* PL4ODP Training Repeat and SOP rule */ + t1_tpi_write(adapter, OFFSET(0x2284), 0x00000000); /* PL4ODP MAX_T setting */ + + t1_tpi_write(adapter, OFFSET(0x3280), 0x00000087); /* PL4IDU Enable data forward, port state machine. Set ALLOW_NON_ZERO_OLB */ + t1_tpi_write(adapter, OFFSET(0x3282), 0x0000001f); /* PL4IDU Enable Dip4 check error interrupts */ + + t1_tpi_write(adapter, OFFSET(0x3040), 0x0c32); /* # TXXG Config */ + /* For T1 use timer based Mac flow control. */ + t1_tpi_write(adapter, OFFSET(0x304d), 0x8000); + t1_tpi_write(adapter, OFFSET(0x2040), 0x059c); /* # RXXG Config */ + t1_tpi_write(adapter, OFFSET(0x2049), 0x0001); /* # RXXG Cut Through */ + t1_tpi_write(adapter, OFFSET(0x2070), 0x0000); /* # Disable promiscuous mode */ + + /* Setup Exact Match Filter 0 to allow broadcast packets. + */ + t1_tpi_write(adapter, OFFSET(0x206e), 0x0000); /* # Disable Match Enable bit */ + t1_tpi_write(adapter, OFFSET(0x204a), 0xffff); /* # low addr */ + t1_tpi_write(adapter, OFFSET(0x204b), 0xffff); /* # mid addr */ + t1_tpi_write(adapter, OFFSET(0x204c), 0xffff); /* # high addr */ + t1_tpi_write(adapter, OFFSET(0x206e), 0x0009); /* # Enable Match Enable bit */ + + t1_tpi_write(adapter, OFFSET(0x0003), 0x0000); /* # NO SOP/ PAD_EN setup */ + t1_tpi_write(adapter, OFFSET(0x0100), 0x0ff0); /* # RXEQB disabled */ + t1_tpi_write(adapter, OFFSET(0x0101), 0x0f0f); /* # No Preemphasis */ + + return cmac; +} + +static int pm3393_mac_reset(adapter_t * adapter) +{ + u32 val; + u32 x; + u32 is_pl4_reset_finished; + u32 is_pl4_outof_lock; + u32 is_xaui_mabc_pll_locked; + u32 successful_reset; + int i; + + /* The following steps are required to properly reset + * the PM3393. This information is provided in the + * PM3393 datasheet (Issue 2: November 2002) + * section 13.1 -- Device Reset. + * + * The PM3393 has three types of components that are + * individually reset: + * + * DRESETB - Digital circuitry + * PL4_ARESETB - PL4 analog circuitry + * XAUI_ARESETB - XAUI bus analog circuitry + * + * Steps to reset PM3393 using RSTB pin: + * + * 1. Assert RSTB pin low ( write 0 ) + * 2. Wait at least 1ms to initiate a complete initialization of device. + * 3. Wait until all external clocks and REFSEL are stable. + * 4. Wait minimum of 1ms. (after external clocks and REFEL are stable) + * 5. De-assert RSTB ( write 1 ) + * 6. Wait until internal timers to expires after ~14ms. + * - Allows analog clock synthesizer(PL4CSU) to stabilize to + * selected reference frequency before allowing the digital + * portion of the device to operate. + * 7. Wait at least 200us for XAUI interface to stabilize. + * 8. Verify the PM3393 came out of reset successfully. + * Set successful reset flag if everything worked else try again + * a few more times. + */ + + successful_reset = 0; + for (i = 0; i < 3 && !successful_reset; i++) { + /* 1 */ + t1_tpi_read(adapter, A_ELMER0_GPO, &val); + val &= ~1; + t1_tpi_write(adapter, A_ELMER0_GPO, val); + + /* 2 */ + msleep(1); + + /* 3 */ + msleep(1); + + /* 4 */ + msleep(2 /*1 extra ms for safety */ ); + + /* 5 */ + val |= 1; + t1_tpi_write(adapter, A_ELMER0_GPO, val); + + /* 6 */ + msleep(15 /*1 extra ms for safety */ ); + + /* 7 */ + msleep(1); + + /* 8 */ + + /* Has PL4 analog block come out of reset correctly? */ + t1_tpi_read(adapter, OFFSET(SUNI1x10GEXP_REG_DEVICE_STATUS), &val); + is_pl4_reset_finished = (val & SUNI1x10GEXP_BITMSK_TOP_EXPIRED); + + /* TBD XXX SUNI1x10GEXP_BITMSK_TOP_PL4_IS_DOOL gets locked later in the init sequence + * figure out why? */ + + /* Have all PL4 block clocks locked? */ + x = (SUNI1x10GEXP_BITMSK_TOP_PL4_ID_DOOL + /*| SUNI1x10GEXP_BITMSK_TOP_PL4_IS_DOOL */ | + SUNI1x10GEXP_BITMSK_TOP_PL4_ID_ROOL | + SUNI1x10GEXP_BITMSK_TOP_PL4_IS_ROOL | + SUNI1x10GEXP_BITMSK_TOP_PL4_OUT_ROOL); + is_pl4_outof_lock = (val & x); + + /* ??? If this fails, might be able to software reset the XAUI part + * and try to recover... thus saving us from doing another HW reset */ + /* Has the XAUI MABC PLL circuitry stablized? */ + is_xaui_mabc_pll_locked = + (val & SUNI1x10GEXP_BITMSK_TOP_SXRA_EXPIRED); + + successful_reset = (is_pl4_reset_finished && !is_pl4_outof_lock + && is_xaui_mabc_pll_locked); + } + return successful_reset ? 0 : 1; +} + +struct gmac t1_pm3393_ops = { + STATS_TICK_SECS, + pm3393_mac_create, + pm3393_mac_reset +}; Index: drivers/net/chelsio/regs.h =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/regs.h (mode:100644) @@ -0,0 +1,468 @@ +/***************************************************************************** + * * + * File: regs.h * + * $Revision: 1.8 $ * + * $Date: 2005/06/21 18:29:48 $ * + * Description: * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#ifndef _CXGB_REGS_H_ +#define _CXGB_REGS_H_ + +/* SGE registers */ +#define A_SG_CONTROL 0x0 + +#define S_CMDQ0_ENABLE 0 +#define V_CMDQ0_ENABLE(x) ((x) << S_CMDQ0_ENABLE) +#define F_CMDQ0_ENABLE V_CMDQ0_ENABLE(1U) + +#define S_CMDQ1_ENABLE 1 +#define V_CMDQ1_ENABLE(x) ((x) << S_CMDQ1_ENABLE) +#define F_CMDQ1_ENABLE V_CMDQ1_ENABLE(1U) + +#define S_FL0_ENABLE 2 +#define V_FL0_ENABLE(x) ((x) << S_FL0_ENABLE) +#define F_FL0_ENABLE V_FL0_ENABLE(1U) + +#define S_FL1_ENABLE 3 +#define V_FL1_ENABLE(x) ((x) << S_FL1_ENABLE) +#define F_FL1_ENABLE V_FL1_ENABLE(1U) + +#define S_CPL_ENABLE 4 +#define V_CPL_ENABLE(x) ((x) << S_CPL_ENABLE) +#define F_CPL_ENABLE V_CPL_ENABLE(1U) + +#define S_RESPONSE_QUEUE_ENABLE 5 +#define V_RESPONSE_QUEUE_ENABLE(x) ((x) << S_RESPONSE_QUEUE_ENABLE) +#define F_RESPONSE_QUEUE_ENABLE V_RESPONSE_QUEUE_ENABLE(1U) + +#define S_CMDQ_PRIORITY 6 +#define M_CMDQ_PRIORITY 0x3 +#define V_CMDQ_PRIORITY(x) ((x) << S_CMDQ_PRIORITY) +#define G_CMDQ_PRIORITY(x) (((x) >> S_CMDQ_PRIORITY) & M_CMDQ_PRIORITY) + +#define S_DISABLE_CMDQ1_GTS 9 +#define V_DISABLE_CMDQ1_GTS(x) ((x) << S_DISABLE_CMDQ1_GTS) +#define F_DISABLE_CMDQ1_GTS V_DISABLE_CMDQ1_GTS(1U) + +#define S_DISABLE_FL0_GTS 10 +#define V_DISABLE_FL0_GTS(x) ((x) << S_DISABLE_FL0_GTS) +#define F_DISABLE_FL0_GTS V_DISABLE_FL0_GTS(1U) + +#define S_DISABLE_FL1_GTS 11 +#define V_DISABLE_FL1_GTS(x) ((x) << S_DISABLE_FL1_GTS) +#define F_DISABLE_FL1_GTS V_DISABLE_FL1_GTS(1U) + +#define S_ENABLE_BIG_ENDIAN 12 +#define V_ENABLE_BIG_ENDIAN(x) ((x) << S_ENABLE_BIG_ENDIAN) +#define F_ENABLE_BIG_ENDIAN V_ENABLE_BIG_ENDIAN(1U) + +#define S_ISCSI_COALESCE 14 +#define V_ISCSI_COALESCE(x) ((x) << S_ISCSI_COALESCE) +#define F_ISCSI_COALESCE V_ISCSI_COALESCE(1U) + +#define S_RX_PKT_OFFSET 15 +#define V_RX_PKT_OFFSET(x) ((x) << S_RX_PKT_OFFSET) + +#define S_VLAN_XTRACT 18 +#define V_VLAN_XTRACT(x) ((x) << S_VLAN_XTRACT) +#define F_VLAN_XTRACT V_VLAN_XTRACT(1U) + +#define A_SG_DOORBELL 0x4 +#define A_SG_CMD0BASELWR 0x8 +#define A_SG_CMD0BASEUPR 0xc +#define A_SG_CMD1BASELWR 0x10 +#define A_SG_CMD1BASEUPR 0x14 +#define A_SG_FL0BASELWR 0x18 +#define A_SG_FL0BASEUPR 0x1c +#define A_SG_FL1BASELWR 0x20 +#define A_SG_FL1BASEUPR 0x24 +#define A_SG_CMD0SIZE 0x28 +#define A_SG_FL0SIZE 0x2c +#define A_SG_RSPSIZE 0x30 +#define A_SG_RSPBASELWR 0x34 +#define A_SG_RSPBASEUPR 0x38 +#define A_SG_FLTHRESHOLD 0x3c +#define A_SG_RSPQUEUECREDIT 0x40 +#define A_SG_SLEEPING 0x48 +#define A_SG_INTRTIMER 0x4c +#define A_SG_CMD1SIZE 0xb0 +#define A_SG_FL1SIZE 0xb4 +#define A_SG_INT_ENABLE 0xb8 + +#define S_RESPQ_EXHAUSTED 0 +#define V_RESPQ_EXHAUSTED(x) ((x) << S_RESPQ_EXHAUSTED) +#define F_RESPQ_EXHAUSTED V_RESPQ_EXHAUSTED(1U) + +#define S_RESPQ_OVERFLOW 1 +#define V_RESPQ_OVERFLOW(x) ((x) << S_RESPQ_OVERFLOW) +#define F_RESPQ_OVERFLOW V_RESPQ_OVERFLOW(1U) + +#define S_FL_EXHAUSTED 2 +#define V_FL_EXHAUSTED(x) ((x) << S_FL_EXHAUSTED) +#define F_FL_EXHAUSTED V_FL_EXHAUSTED(1U) + +#define S_PACKET_TOO_BIG 3 +#define V_PACKET_TOO_BIG(x) ((x) << S_PACKET_TOO_BIG) +#define F_PACKET_TOO_BIG V_PACKET_TOO_BIG(1U) + +#define S_PACKET_MISMATCH 4 +#define V_PACKET_MISMATCH(x) ((x) << S_PACKET_MISMATCH) +#define F_PACKET_MISMATCH V_PACKET_MISMATCH(1U) + +#define A_SG_INT_CAUSE 0xbc +#define A_SG_RESPACCUTIMER 0xc0 + +/* MC3 registers */ + +#define S_READY 1 +#define V_READY(x) ((x) << S_READY) +#define F_READY V_READY(1U) + +/* MC4 registers */ + +#define A_MC4_CFG 0x180 +#define S_MC4_SLOW 25 +#define V_MC4_SLOW(x) ((x) << S_MC4_SLOW) +#define F_MC4_SLOW V_MC4_SLOW(1U) + +/* TPI registers */ + +#define A_TPI_ADDR 0x280 +#define A_TPI_WR_DATA 0x284 +#define A_TPI_RD_DATA 0x288 +#define A_TPI_CSR 0x28c + +#define S_TPIWR 0 +#define V_TPIWR(x) ((x) << S_TPIWR) +#define F_TPIWR V_TPIWR(1U) + +#define S_TPIRDY 1 +#define V_TPIRDY(x) ((x) << S_TPIRDY) +#define F_TPIRDY V_TPIRDY(1U) + +#define A_TPI_PAR 0x29c + +#define S_TPIPAR 0 +#define M_TPIPAR 0x7f +#define V_TPIPAR(x) ((x) << S_TPIPAR) +#define G_TPIPAR(x) (((x) >> S_TPIPAR) & M_TPIPAR) + +/* TP registers */ + +#define A_TP_IN_CONFIG 0x300 + +#define S_TP_IN_CSPI_CPL 3 +#define V_TP_IN_CSPI_CPL(x) ((x) << S_TP_IN_CSPI_CPL) +#define F_TP_IN_CSPI_CPL V_TP_IN_CSPI_CPL(1U) + +#define S_TP_IN_CSPI_CHECK_IP_CSUM 5 +#define V_TP_IN_CSPI_CHECK_IP_CSUM(x) ((x) << S_TP_IN_CSPI_CHECK_IP_CSUM) +#define F_TP_IN_CSPI_CHECK_IP_CSUM V_TP_IN_CSPI_CHECK_IP_CSUM(1U) + +#define S_TP_IN_CSPI_CHECK_TCP_CSUM 6 +#define V_TP_IN_CSPI_CHECK_TCP_CSUM(x) ((x) << S_TP_IN_CSPI_CHECK_TCP_CSUM) +#define F_TP_IN_CSPI_CHECK_TCP_CSUM V_TP_IN_CSPI_CHECK_TCP_CSUM(1U) + +#define S_TP_IN_ESPI_ETHERNET 8 +#define V_TP_IN_ESPI_ETHERNET(x) ((x) << S_TP_IN_ESPI_ETHERNET) +#define F_TP_IN_ESPI_ETHERNET V_TP_IN_ESPI_ETHERNET(1U) + +#define S_TP_IN_ESPI_CHECK_IP_CSUM 12 +#define V_TP_IN_ESPI_CHECK_IP_CSUM(x) ((x) << S_TP_IN_ESPI_CHECK_IP_CSUM) +#define F_TP_IN_ESPI_CHECK_IP_CSUM V_TP_IN_ESPI_CHECK_IP_CSUM(1U) + +#define S_TP_IN_ESPI_CHECK_TCP_CSUM 13 +#define V_TP_IN_ESPI_CHECK_TCP_CSUM(x) ((x) << S_TP_IN_ESPI_CHECK_TCP_CSUM) +#define F_TP_IN_ESPI_CHECK_TCP_CSUM V_TP_IN_ESPI_CHECK_TCP_CSUM(1U) + +#define S_OFFLOAD_DISABLE 14 +#define V_OFFLOAD_DISABLE(x) ((x) << S_OFFLOAD_DISABLE) +#define F_OFFLOAD_DISABLE V_OFFLOAD_DISABLE(1U) + +#define A_TP_OUT_CONFIG 0x304 + +#define S_TP_OUT_CSPI_CPL 2 +#define V_TP_OUT_CSPI_CPL(x) ((x) << S_TP_OUT_CSPI_CPL) +#define F_TP_OUT_CSPI_CPL V_TP_OUT_CSPI_CPL(1U) + +#define S_TP_OUT_ESPI_ETHERNET 6 +#define V_TP_OUT_ESPI_ETHERNET(x) ((x) << S_TP_OUT_ESPI_ETHERNET) +#define F_TP_OUT_ESPI_ETHERNET V_TP_OUT_ESPI_ETHERNET(1U) + +#define S_TP_OUT_ESPI_GENERATE_IP_CSUM 10 +#define V_TP_OUT_ESPI_GENERATE_IP_CSUM(x) ((x) << S_TP_OUT_ESPI_GENERATE_IP_CSUM) +#define F_TP_OUT_ESPI_GENERATE_IP_CSUM V_TP_OUT_ESPI_GENERATE_IP_CSUM(1U) + +#define S_TP_OUT_ESPI_GENERATE_TCP_CSUM 11 +#define V_TP_OUT_ESPI_GENERATE_TCP_CSUM(x) ((x) << S_TP_OUT_ESPI_GENERATE_TCP_CSUM) +#define F_TP_OUT_ESPI_GENERATE_TCP_CSUM V_TP_OUT_ESPI_GENERATE_TCP_CSUM(1U) + +#define A_TP_GLOBAL_CONFIG 0x308 + +#define S_IP_TTL 0 +#define M_IP_TTL 0xff +#define V_IP_TTL(x) ((x) << S_IP_TTL) + +#define S_TCP_CSUM 11 +#define V_TCP_CSUM(x) ((x) << S_TCP_CSUM) +#define F_TCP_CSUM V_TCP_CSUM(1U) + +#define S_UDP_CSUM 12 +#define V_UDP_CSUM(x) ((x) << S_UDP_CSUM) +#define F_UDP_CSUM V_UDP_CSUM(1U) + +#define S_IP_CSUM 13 +#define V_IP_CSUM(x) ((x) << S_IP_CSUM) +#define F_IP_CSUM V_IP_CSUM(1U) + +#define S_PATH_MTU 15 +#define V_PATH_MTU(x) ((x) << S_PATH_MTU) +#define F_PATH_MTU V_PATH_MTU(1U) + +#define S_5TUPLE_LOOKUP 17 +#define V_5TUPLE_LOOKUP(x) ((x) << S_5TUPLE_LOOKUP) + +#define S_SYN_COOKIE_PARAMETER 26 +#define V_SYN_COOKIE_PARAMETER(x) ((x) << S_SYN_COOKIE_PARAMETER) + +#define A_TP_PC_CONFIG 0x348 +#define S_DIS_TX_FILL_WIN_PUSH 12 +#define V_DIS_TX_FILL_WIN_PUSH(x) ((x) << S_DIS_TX_FILL_WIN_PUSH) +#define F_DIS_TX_FILL_WIN_PUSH V_DIS_TX_FILL_WIN_PUSH(1U) + +#define S_TP_PC_REV 30 +#define M_TP_PC_REV 0x3 +#define G_TP_PC_REV(x) (((x) >> S_TP_PC_REV) & M_TP_PC_REV) +#define A_TP_RESET 0x44c +#define S_TP_RESET 0 +#define V_TP_RESET(x) ((x) << S_TP_RESET) +#define F_TP_RESET V_TP_RESET(1U) + +#define A_TP_INT_ENABLE 0x470 +#define A_TP_INT_CAUSE 0x474 +#define A_TP_TX_DROP_CONFIG 0x4b8 + +#define S_ENABLE_TX_DROP 31 +#define V_ENABLE_TX_DROP(x) ((x) << S_ENABLE_TX_DROP) +#define F_ENABLE_TX_DROP V_ENABLE_TX_DROP(1U) + +#define S_ENABLE_TX_ERROR 30 +#define V_ENABLE_TX_ERROR(x) ((x) << S_ENABLE_TX_ERROR) +#define F_ENABLE_TX_ERROR V_ENABLE_TX_ERROR(1U) + +#define S_DROP_TICKS_CNT 4 +#define V_DROP_TICKS_CNT(x) ((x) << S_DROP_TICKS_CNT) + +#define S_NUM_PKTS_DROPPED 0 +#define V_NUM_PKTS_DROPPED(x) ((x) << S_NUM_PKTS_DROPPED) + +/* CSPI registers */ + +#define S_DIP4ERR 0 +#define V_DIP4ERR(x) ((x) << S_DIP4ERR) +#define F_DIP4ERR V_DIP4ERR(1U) + +#define S_RXDROP 1 +#define V_RXDROP(x) ((x) << S_RXDROP) +#define F_RXDROP V_RXDROP(1U) + +#define S_TXDROP 2 +#define V_TXDROP(x) ((x) << S_TXDROP) +#define F_TXDROP V_TXDROP(1U) + +#define S_RXOVERFLOW 3 +#define V_RXOVERFLOW(x) ((x) << S_RXOVERFLOW) +#define F_RXOVERFLOW V_RXOVERFLOW(1U) + +#define S_RAMPARITYERR 4 +#define V_RAMPARITYERR(x) ((x) << S_RAMPARITYERR) +#define F_RAMPARITYERR V_RAMPARITYERR(1U) + +/* ESPI registers */ + +#define A_ESPI_SCH_TOKEN0 0x880 +#define A_ESPI_SCH_TOKEN1 0x884 +#define A_ESPI_SCH_TOKEN2 0x888 +#define A_ESPI_SCH_TOKEN3 0x88c +#define A_ESPI_RX_FIFO_ALMOST_EMPTY_WATERMARK 0x890 +#define A_ESPI_RX_FIFO_ALMOST_FULL_WATERMARK 0x894 +#define A_ESPI_CALENDAR_LENGTH 0x898 +#define A_PORT_CONFIG 0x89c + +#define S_RX_NPORTS 0 +#define V_RX_NPORTS(x) ((x) << S_RX_NPORTS) + +#define S_TX_NPORTS 8 +#define V_TX_NPORTS(x) ((x) << S_TX_NPORTS) + +#define A_ESPI_FIFO_STATUS_ENABLE 0x8a0 + +#define S_RXSTATUSENABLE 0 +#define V_RXSTATUSENABLE(x) ((x) << S_RXSTATUSENABLE) +#define F_RXSTATUSENABLE V_RXSTATUSENABLE(1U) + +#define S_INTEL1010MODE 4 +#define V_INTEL1010MODE(x) ((x) << S_INTEL1010MODE) +#define F_INTEL1010MODE V_INTEL1010MODE(1U) + +#define A_ESPI_MAXBURST1_MAXBURST2 0x8a8 +#define A_ESPI_TRAIN 0x8ac +#define A_ESPI_INTR_STATUS 0x8c8 + +#define S_DIP2PARITYERR 5 +#define V_DIP2PARITYERR(x) ((x) << S_DIP2PARITYERR) +#define F_DIP2PARITYERR V_DIP2PARITYERR(1U) + +#define A_ESPI_INTR_ENABLE 0x8cc +#define A_RX_DROP_THRESHOLD 0x8d0 +#define A_ESPI_RX_RESET 0x8ec +#define A_ESPI_MISC_CONTROL 0x8f0 + +#define S_OUT_OF_SYNC_COUNT 0 +#define V_OUT_OF_SYNC_COUNT(x) ((x) << S_OUT_OF_SYNC_COUNT) + +#define S_DIP2_PARITY_ERR_THRES 5 +#define V_DIP2_PARITY_ERR_THRES(x) ((x) << S_DIP2_PARITY_ERR_THRES) + +#define S_DIP4_THRES 9 +#define V_DIP4_THRES(x) ((x) << S_DIP4_THRES) + +#define S_MONITORED_PORT_NUM 25 +#define V_MONITORED_PORT_NUM(x) ((x) << S_MONITORED_PORT_NUM) + +#define S_MONITORED_DIRECTION 27 +#define V_MONITORED_DIRECTION(x) ((x) << S_MONITORED_DIRECTION) +#define F_MONITORED_DIRECTION V_MONITORED_DIRECTION(1U) + +#define S_MONITORED_INTERFACE 28 +#define V_MONITORED_INTERFACE(x) ((x) << S_MONITORED_INTERFACE) +#define F_MONITORED_INTERFACE V_MONITORED_INTERFACE(1U) + +#define A_ESPI_DIP2_ERR_COUNT 0x8f4 +#define A_ESPI_CMD_ADDR 0x8f8 + +#define S_WRITE_DATA 0 +#define V_WRITE_DATA(x) ((x) << S_WRITE_DATA) + +#define S_REGISTER_OFFSET 8 +#define V_REGISTER_OFFSET(x) ((x) << S_REGISTER_OFFSET) + +#define S_CHANNEL_ADDR 12 +#define V_CHANNEL_ADDR(x) ((x) << S_CHANNEL_ADDR) + +#define S_MODULE_ADDR 16 +#define V_MODULE_ADDR(x) ((x) << S_MODULE_ADDR) + +#define S_BUNDLE_ADDR 20 +#define V_BUNDLE_ADDR(x) ((x) << S_BUNDLE_ADDR) + +#define S_SPI4_COMMAND 24 +#define V_SPI4_COMMAND(x) ((x) << S_SPI4_COMMAND) + +#define A_ESPI_GOSTAT 0x8fc +#define S_ESPI_CMD_BUSY 8 +#define V_ESPI_CMD_BUSY(x) ((x) << S_ESPI_CMD_BUSY) +#define F_ESPI_CMD_BUSY V_ESPI_CMD_BUSY(1U) + +/* PL registers */ + +#define A_PL_ENABLE 0xa00 + +#define S_PL_INTR_SGE_ERR 0 +#define V_PL_INTR_SGE_ERR(x) ((x) << S_PL_INTR_SGE_ERR) +#define F_PL_INTR_SGE_ERR V_PL_INTR_SGE_ERR(1U) + +#define S_PL_INTR_SGE_DATA 1 +#define V_PL_INTR_SGE_DATA(x) ((x) << S_PL_INTR_SGE_DATA) +#define F_PL_INTR_SGE_DATA V_PL_INTR_SGE_DATA(1U) + +#define S_PL_INTR_TP 6 +#define V_PL_INTR_TP(x) ((x) << S_PL_INTR_TP) +#define F_PL_INTR_TP V_PL_INTR_TP(1U) + +#define S_PL_INTR_ESPI 8 +#define V_PL_INTR_ESPI(x) ((x) << S_PL_INTR_ESPI) +#define F_PL_INTR_ESPI V_PL_INTR_ESPI(1U) + +#define S_PL_INTR_PCIX 10 +#define V_PL_INTR_PCIX(x) ((x) << S_PL_INTR_PCIX) +#define F_PL_INTR_PCIX V_PL_INTR_PCIX(1U) + +#define S_PL_INTR_EXT 11 +#define V_PL_INTR_EXT(x) ((x) << S_PL_INTR_EXT) +#define F_PL_INTR_EXT V_PL_INTR_EXT(1U) + +#define A_PL_CAUSE 0xa04 + +/* MC5 registers */ + +#define A_MC5_CONFIG 0xc04 + +#define S_TCAM_RESET 1 +#define V_TCAM_RESET(x) ((x) << S_TCAM_RESET) +#define F_TCAM_RESET V_TCAM_RESET(1U) + +#define S_M_BUS_ENABLE 5 +#define V_M_BUS_ENABLE(x) ((x) << S_M_BUS_ENABLE) +#define F_M_BUS_ENABLE V_M_BUS_ENABLE(1U) + +/* PCICFG registers */ + +#define A_PCICFG_PM_CSR 0x44 +#define A_PCICFG_VPD_ADDR 0x4a + +#define S_VPD_OP_FLAG 15 +#define V_VPD_OP_FLAG(x) ((x) << S_VPD_OP_FLAG) +#define F_VPD_OP_FLAG V_VPD_OP_FLAG(1U) + +#define A_PCICFG_VPD_DATA 0x4c + +#define A_PCICFG_INTR_ENABLE 0xf4 +#define A_PCICFG_INTR_CAUSE 0xf8 + +#define A_PCICFG_MODE 0xfc + +#define S_PCI_MODE_64BIT 0 +#define V_PCI_MODE_64BIT(x) ((x) << S_PCI_MODE_64BIT) +#define F_PCI_MODE_64BIT V_PCI_MODE_64BIT(1U) + +#define S_PCI_MODE_PCIX 5 +#define V_PCI_MODE_PCIX(x) ((x) << S_PCI_MODE_PCIX) +#define F_PCI_MODE_PCIX V_PCI_MODE_PCIX(1U) + +#define S_PCI_MODE_CLK 6 +#define M_PCI_MODE_CLK 0x3 +#define G_PCI_MODE_CLK(x) (((x) >> S_PCI_MODE_CLK) & M_PCI_MODE_CLK) + +#endif /* _CXGB_REGS_H_ */ Index: drivers/net/chelsio/sge.c =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/sge.c (mode:100644) @@ -0,0 +1,1684 @@ +/***************************************************************************** + * * + * File: sge.c * + * $Revision: 1.26 $ * + * $Date: 2005/06/21 18:29:48 $ * + * Description: * + * DMA engine. * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#include "common.h" + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "cpl5_cmd.h" +#include "sge.h" +#include "regs.h" +#include "espi.h" + + +#ifdef NETIF_F_TSO +#include +#endif + +#define SGE_CMDQ_N 2 +#define SGE_FREELQ_N 2 +#define SGE_CMDQ0_E_N 1024 +#define SGE_CMDQ1_E_N 128 +#define SGE_FREEL_SIZE 4096 +#define SGE_JUMBO_FREEL_SIZE 512 +#define SGE_FREEL_REFILL_THRESH 16 +#define SGE_RESPQ_E_N 1024 +#define SGE_INTRTIMER_NRES 1000 +#define SGE_RX_COPY_THRES 256 +#define SGE_RX_SM_BUF_SIZE 1536 + +# define SGE_RX_DROP_THRES 2 + +#define SGE_RESPQ_REPLENISH_THRES (SGE_RESPQ_E_N / 4) + +/* + * Period of the TX buffer reclaim timer. This timer does not need to run + * frequently as TX buffers are usually reclaimed by new TX packets. + */ +#define TX_RECLAIM_PERIOD (HZ / 4) + +#ifndef NET_IP_ALIGN +# define NET_IP_ALIGN 2 +#endif + +#define M_CMD_LEN 0x7fffffff +#define V_CMD_LEN(v) (v) +#define G_CMD_LEN(v) ((v) & M_CMD_LEN) +#define V_CMD_GEN1(v) ((v) << 31) +#define V_CMD_GEN2(v) (v) +#define F_CMD_DATAVALID (1 << 1) +#define F_CMD_SOP (1 << 2) +#define V_CMD_EOP(v) ((v) << 3) + +/* + * Command queue, receive buffer list, and response queue descriptors. + */ +#if defined(__BIG_ENDIAN_BITFIELD) +struct cmdQ_e { + u32 addr_lo; + u32 len_gen; + u32 flags; + u32 addr_hi; +}; + +struct freelQ_e { + u32 addr_lo; + u32 len_gen; + u32 gen2; + u32 addr_hi; +}; + +struct respQ_e { + u32 Qsleeping : 4; + u32 Cmdq1CreditReturn : 5; + u32 Cmdq1DmaComplete : 5; + u32 Cmdq0CreditReturn : 5; + u32 Cmdq0DmaComplete : 5; + u32 FreelistQid : 2; + u32 CreditValid : 1; + u32 DataValid : 1; + u32 Offload : 1; + u32 Eop : 1; + u32 Sop : 1; + u32 GenerationBit : 1; + u32 BufferLength; +}; +#elif defined(__LITTLE_ENDIAN_BITFIELD) +struct cmdQ_e { + u32 len_gen; + u32 addr_lo; + u32 addr_hi; + u32 flags; +}; + +struct freelQ_e { + u32 len_gen; + u32 addr_lo; + u32 addr_hi; + u32 gen2; +}; + +struct respQ_e { + u32 BufferLength; + u32 GenerationBit : 1; + u32 Sop : 1; + u32 Eop : 1; + u32 Offload : 1; + u32 DataValid : 1; + u32 CreditValid : 1; + u32 FreelistQid : 2; + u32 Cmdq0DmaComplete : 5; + u32 Cmdq0CreditReturn : 5; + u32 Cmdq1DmaComplete : 5; + u32 Cmdq1CreditReturn : 5; + u32 Qsleeping : 4; +} ; +#endif + +/* + * SW Context Command and Freelist Queue Descriptors + */ +struct cmdQ_ce { + struct sk_buff *skb; + DECLARE_PCI_UNMAP_ADDR(dma_addr); + DECLARE_PCI_UNMAP_LEN(dma_len); +}; + +struct freelQ_ce { + struct sk_buff *skb; + DECLARE_PCI_UNMAP_ADDR(dma_addr); + DECLARE_PCI_UNMAP_LEN(dma_len); +}; + +/* + * SW command, freelist and response rings + */ +struct cmdQ { + unsigned long status; /* HW DMA fetch status */ + unsigned int in_use; /* # of in-use command descriptors */ + unsigned int size; /* # of descriptors */ + unsigned int processed; /* total # of descs HW has processed */ + unsigned int cleaned; /* total # of descs SW has reclaimed */ + unsigned int stop_thres; /* SW TX queue suspend threshold */ + u16 pidx; /* producer index (SW) */ + u16 cidx; /* consumer index (HW) */ + u8 genbit; /* current generation (=valid) bit */ + u8 sop; /* is next entry start of packet? */ + struct cmdQ_e *entries; /* HW command descriptor Q */ + struct cmdQ_ce *centries; /* SW command context descriptor Q */ + spinlock_t lock; /* Lock to protect cmdQ enqueuing */ + dma_addr_t dma_addr; /* DMA addr HW command descriptor Q */ +}; + +struct freelQ { + unsigned int credits; /* # of available RX buffers */ + unsigned int size; /* free list capacity */ + u16 pidx; /* producer index (SW) */ + u16 cidx; /* consumer index (HW) */ + u16 rx_buffer_size; /* Buffer size on this free list */ + u16 dma_offset; /* DMA offset to align IP headers */ + u16 recycleq_idx; /* skb recycle q to use */ + u8 genbit; /* current generation (=valid) bit */ + struct freelQ_e *entries; /* HW freelist descriptor Q */ + struct freelQ_ce *centries; /* SW freelist context descriptor Q */ + dma_addr_t dma_addr; /* DMA addr HW freelist descriptor Q */ +}; + +struct respQ { + unsigned int credits; /* credits to be returned to SGE */ + unsigned int size; /* # of response Q descriptors */ + u16 cidx; /* consumer index (SW) */ + u8 genbit; /* current generation(=valid) bit */ + struct respQ_e *entries; /* HW response descriptor Q */ + dma_addr_t dma_addr; /* DMA addr HW response descriptor Q */ +}; + +/* Bit flags for cmdQ.status */ +enum { + CMDQ_STAT_RUNNING = 1, /* fetch engine is running */ + CMDQ_STAT_LAST_PKT_DB = 2 /* last packet rung the doorbell */ +}; + +/* + * Main SGE data structure + * + * Interrupts are handled by a single CPU and it is likely that on a MP system + * the application is migrated to another CPU. In that scenario, we try to + * seperate the RX(in irq context) and TX state in order to decrease memory + * contention. + */ +struct sge { + struct adapter *adapter; /* adapter backpointer */ + struct net_device *netdev; /* netdevice backpointer */ + struct freelQ freelQ[SGE_FREELQ_N]; /* buffer free lists */ + struct respQ respQ; /* response Q */ + unsigned long stopped_tx_queues; /* bitmap of suspended Tx queues */ + unsigned int rx_pkt_pad; /* RX padding for L2 packets */ + unsigned int jumbo_fl; /* jumbo freelist Q index */ + unsigned int intrtimer_nres; /* no-resource interrupt timer */ + unsigned int fixed_intrtimer;/* non-adaptive interrupt timer */ + struct timer_list tx_reclaim_timer; /* reclaims TX buffers */ + struct timer_list espibug_timer; + unsigned int espibug_timeout; + struct sk_buff *espibug_skb; + u32 sge_control; /* shadow value of sge control reg */ + struct sge_intr_counts stats; + struct sge_port_stats port_stats[MAX_NPORTS]; + struct cmdQ cmdQ[SGE_CMDQ_N] ____cacheline_aligned_in_smp; +}; + +/* + * PIO to indicate that memory mapped Q contains valid descriptor(s). + */ +static inline void doorbell_pio(struct adapter *adapter, u32 val) +{ + wmb(); + writel(val, adapter->regs + A_SG_DOORBELL); +} + +/* + * Frees all RX buffers on the freelist Q. The caller must make sure that + * the SGE is turned off before calling this function. + */ +static void free_freelQ_buffers(struct pci_dev *pdev, struct freelQ *q) +{ + unsigned int cidx = q->cidx; + + while (q->credits--) { + struct freelQ_ce *ce = &q->centries[cidx]; + + pci_unmap_single(pdev, pci_unmap_addr(ce, dma_addr), + pci_unmap_len(ce, dma_len), + PCI_DMA_FROMDEVICE); + dev_kfree_skb(ce->skb); + ce->skb = NULL; + if (++cidx == q->size) + cidx = 0; + } +} + +/* + * Free RX free list and response queue resources. + */ +static void free_rx_resources(struct sge *sge) +{ + struct pci_dev *pdev = sge->adapter->pdev; + unsigned int size, i; + + if (sge->respQ.entries) { + size = sizeof(struct respQ_e) * sge->respQ.size; + pci_free_consistent(pdev, size, sge->respQ.entries, + sge->respQ.dma_addr); + } + + for (i = 0; i < SGE_FREELQ_N; i++) { + struct freelQ *q = &sge->freelQ[i]; + + if (q->centries) { + free_freelQ_buffers(pdev, q); + kfree(q->centries); + } + if (q->entries) { + size = sizeof(struct freelQ_e) * q->size; + pci_free_consistent(pdev, size, q->entries, + q->dma_addr); + } + } +} + +/* + * Allocates basic RX resources, consisting of memory mapped freelist Qs and a + * response queue. + */ +static int alloc_rx_resources(struct sge *sge, struct sge_params *p) +{ + struct pci_dev *pdev = sge->adapter->pdev; + unsigned int size, i; + + for (i = 0; i < SGE_FREELQ_N; i++) { + struct freelQ *q = &sge->freelQ[i]; + + q->genbit = 1; + q->size = p->freelQ_size[i]; + q->dma_offset = sge->rx_pkt_pad ? 0 : NET_IP_ALIGN; + size = sizeof(struct freelQ_e) * q->size; + q->entries = (struct freelQ_e *) + pci_alloc_consistent(pdev, size, &q->dma_addr); + if (!q->entries) + goto err_no_mem; + memset(q->entries, 0, size); + size = sizeof(struct freelQ_ce) * q->size; + q->centries = kmalloc(size, GFP_KERNEL); + if (!q->centries) + goto err_no_mem; + memset(q->centries, 0, size); + } + + /* + * Calculate the buffer sizes for the two free lists. FL0 accommodates + * regular sized Ethernet frames, FL1 is sized not to exceed 16K, + * including all the sk_buff overhead. + * + * Note: For T2 FL0 and FL1 are reversed. + */ + sge->freelQ[!sge->jumbo_fl].rx_buffer_size = SGE_RX_SM_BUF_SIZE + + sizeof(struct cpl_rx_data) + + sge->freelQ[!sge->jumbo_fl].dma_offset; + sge->freelQ[sge->jumbo_fl].rx_buffer_size = (16 * 1024) - + SKB_DATA_ALIGN(sizeof(struct skb_shared_info)); + + /* + * Setup which skb recycle Q should be used when recycling buffers from + * each free list. + */ + sge->freelQ[!sge->jumbo_fl].recycleq_idx = 0; + sge->freelQ[sge->jumbo_fl].recycleq_idx = 1; + + sge->respQ.genbit = 1; + sge->respQ.size = SGE_RESPQ_E_N; + sge->respQ.credits = 0; + size = sizeof(struct respQ_e) * sge->respQ.size; + sge->respQ.entries = (struct respQ_e *) + pci_alloc_consistent(pdev, size, &sge->respQ.dma_addr); + if (!sge->respQ.entries) + goto err_no_mem; + memset(sge->respQ.entries, 0, size); + return 0; + +err_no_mem: + free_rx_resources(sge); + return -ENOMEM; +} + +/* + * Reclaims n TX descriptors and frees the buffers associated with them. + */ +static void free_cmdQ_buffers(struct sge *sge, struct cmdQ *q, unsigned int n) +{ + struct cmdQ_ce *ce; + struct pci_dev *pdev = sge->adapter->pdev; + unsigned int cidx = q->cidx; + + q->in_use -= n; + ce = &q->centries[cidx]; + while (n--) { + if (q->sop) + pci_unmap_single(pdev, pci_unmap_addr(ce, dma_addr), + pci_unmap_len(ce, dma_len), + PCI_DMA_TODEVICE); + else + pci_unmap_page(pdev, pci_unmap_addr(ce, dma_addr), + pci_unmap_len(ce, dma_len), + PCI_DMA_TODEVICE); + q->sop = 0; + if (ce->skb) { + dev_kfree_skb(ce->skb); + q->sop = 1; + } + ce++; + if (++cidx == q->size) { + cidx = 0; + ce = q->centries; + } + } + q->cidx = cidx; +} + +/* + * Free TX resources. + * + * Assumes that SGE is stopped and all interrupts are disabled. + */ +static void free_tx_resources(struct sge *sge) +{ + struct pci_dev *pdev = sge->adapter->pdev; + unsigned int size, i; + + for (i = 0; i < SGE_CMDQ_N; i++) { + struct cmdQ *q = &sge->cmdQ[i]; + + if (q->centries) { + if (q->in_use) + free_cmdQ_buffers(sge, q, q->in_use); + kfree(q->centries); + } + if (q->entries) { + size = sizeof(struct cmdQ_e) * q->size; + pci_free_consistent(pdev, size, q->entries, + q->dma_addr); + } + } +} + +/* + * Allocates basic TX resources, consisting of memory mapped command Qs. + */ +static int alloc_tx_resources(struct sge *sge, struct sge_params *p) +{ + struct pci_dev *pdev = sge->adapter->pdev; + unsigned int size, i; + + for (i = 0; i < SGE_CMDQ_N; i++) { + struct cmdQ *q = &sge->cmdQ[i]; + + q->genbit = 1; + q->sop = 1; + q->size = p->cmdQ_size[i]; + q->in_use = 0; + q->status = 0; + q->processed = q->cleaned = 0; + q->stop_thres = 0; + spin_lock_init(&q->lock); + size = sizeof(struct cmdQ_e) * q->size; + q->entries = (struct cmdQ_e *) + pci_alloc_consistent(pdev, size, &q->dma_addr); + if (!q->entries) + goto err_no_mem; + memset(q->entries, 0, size); + size = sizeof(struct cmdQ_ce) * q->size; + q->centries = kmalloc(size, GFP_KERNEL); + if (!q->centries) + goto err_no_mem; + memset(q->centries, 0, size); + } + + /* + * CommandQ 0 handles Ethernet and TOE packets, while queue 1 is TOE + * only. For queue 0 set the stop threshold so we can handle one more + * packet from each port, plus reserve an additional 24 entries for + * Ethernet packets only. Queue 1 never suspends nor do we reserve + * space for Ethernet packets. + */ + sge->cmdQ[0].stop_thres = sge->adapter->params.nports * + (MAX_SKB_FRAGS + 1); + return 0; + +err_no_mem: + free_tx_resources(sge); + return -ENOMEM; +} + +static inline void setup_ring_params(struct adapter *adapter, u64 addr, + u32 size, int base_reg_lo, + int base_reg_hi, int size_reg) +{ + writel((u32)addr, adapter->regs + base_reg_lo); + writel(addr >> 32, adapter->regs + base_reg_hi); + writel(size, adapter->regs + size_reg); +} + +/* + * Enable/disable VLAN acceleration. + */ +void t1_set_vlan_accel(struct adapter *adapter, int on_off) +{ + struct sge *sge = adapter->sge; + + sge->sge_control &= ~F_VLAN_XTRACT; + if (on_off) + sge->sge_control |= F_VLAN_XTRACT; + if (adapter->open_device_map) { + writel(sge->sge_control, adapter->regs + A_SG_CONTROL); + readl(adapter->regs + A_SG_CONTROL); /* flush */ + } +} + +/* + * Programs the various SGE registers. However, the engine is not yet enabled, + * but sge->sge_control is setup and ready to go. + */ +static void configure_sge(struct sge *sge, struct sge_params *p) +{ + struct adapter *ap = sge->adapter; + + writel(0, ap->regs + A_SG_CONTROL); + setup_ring_params(ap, sge->cmdQ[0].dma_addr, sge->cmdQ[0].size, + A_SG_CMD0BASELWR, A_SG_CMD0BASEUPR, A_SG_CMD0SIZE); + setup_ring_params(ap, sge->cmdQ[1].dma_addr, sge->cmdQ[1].size, + A_SG_CMD1BASELWR, A_SG_CMD1BASEUPR, A_SG_CMD1SIZE); + setup_ring_params(ap, sge->freelQ[0].dma_addr, + sge->freelQ[0].size, A_SG_FL0BASELWR, + A_SG_FL0BASEUPR, A_SG_FL0SIZE); + setup_ring_params(ap, sge->freelQ[1].dma_addr, + sge->freelQ[1].size, A_SG_FL1BASELWR, + A_SG_FL1BASEUPR, A_SG_FL1SIZE); + + /* The threshold comparison uses <. */ + writel(SGE_RX_SM_BUF_SIZE + 1, ap->regs + A_SG_FLTHRESHOLD); + + setup_ring_params(ap, sge->respQ.dma_addr, sge->respQ.size, + A_SG_RSPBASELWR, A_SG_RSPBASEUPR, A_SG_RSPSIZE); + writel((u32)sge->respQ.size - 1, ap->regs + A_SG_RSPQUEUECREDIT); + + sge->sge_control = F_CMDQ0_ENABLE | F_CMDQ1_ENABLE | F_FL0_ENABLE | + F_FL1_ENABLE | F_CPL_ENABLE | F_RESPONSE_QUEUE_ENABLE | + V_CMDQ_PRIORITY(2) | F_DISABLE_CMDQ1_GTS | F_ISCSI_COALESCE | + F_DISABLE_FL0_GTS | F_DISABLE_FL1_GTS | + V_RX_PKT_OFFSET(sge->rx_pkt_pad); + +#if defined(__BIG_ENDIAN_BITFIELD) + sge->sge_control |= F_ENABLE_BIG_ENDIAN; +#endif + + /* Initialize no-resource timer */ + sge->intrtimer_nres = SGE_INTRTIMER_NRES * core_ticks_per_usec(ap); + + t1_sge_set_coalesce_params(sge, p); +} + +/* + * Return the payload capacity of the jumbo free-list buffers. + */ +static inline unsigned int jumbo_payload_capacity(const struct sge *sge) +{ + return sge->freelQ[sge->jumbo_fl].rx_buffer_size - + sge->freelQ[sge->jumbo_fl].dma_offset - + sizeof(struct cpl_rx_data); +} + +/* + * Frees all SGE related resources and the sge structure itself + */ +void t1_sge_destroy(struct sge *sge) +{ + if (sge->espibug_skb) + kfree_skb(sge->espibug_skb); + + free_tx_resources(sge); + free_rx_resources(sge); + kfree(sge); +} + +/* + * Allocates new RX buffers on the freelist Q (and tracks them on the freelist + * context Q) until the Q is full or alloc_skb fails. + * + * It is possible that the generation bits already match, indicating that the + * buffer is already valid and nothing needs to be done. This happens when we + * copied a received buffer into a new sk_buff during the interrupt processing. + * + * If the SGE doesn't automatically align packets properly (!sge->rx_pkt_pad), + * we specify a RX_OFFSET in order to make sure that the IP header is 4B + * aligned. + */ +static void refill_free_list(struct sge *sge, struct freelQ *q) +{ + struct pci_dev *pdev = sge->adapter->pdev; + struct freelQ_ce *ce = &q->centries[q->pidx]; + struct freelQ_e *e = &q->entries[q->pidx]; + unsigned int dma_len = q->rx_buffer_size - q->dma_offset; + + + while (q->credits < q->size) { + struct sk_buff *skb; + dma_addr_t mapping; + + skb = alloc_skb(q->rx_buffer_size, GFP_ATOMIC); + if (!skb) + break; + + skb_reserve(skb, q->dma_offset); + mapping = pci_map_single(pdev, skb->data, dma_len, + PCI_DMA_FROMDEVICE); + ce->skb = skb; + pci_unmap_addr_set(ce, dma_addr, mapping); + pci_unmap_len_set(ce, dma_len, dma_len); + e->addr_lo = (u32)mapping; + e->addr_hi = (u64)mapping >> 32; + e->len_gen = V_CMD_LEN(dma_len) | V_CMD_GEN1(q->genbit); + wmb(); + e->gen2 = V_CMD_GEN2(q->genbit); + + e++; + ce++; + if (++q->pidx == q->size) { + q->pidx = 0; + q->genbit ^= 1; + ce = q->centries; + e = q->entries; + } + q->credits++; + } + +} + +/* + * Calls refill_free_list for both free lists. If we cannot fill at least 1/4 + * of both rings, we go into 'few interrupt mode' in order to give the system + * time to free up resources. + */ +static void freelQs_empty(struct sge *sge) +{ + struct adapter *adapter = sge->adapter; + u32 irq_reg = readl(adapter->regs + A_SG_INT_ENABLE); + u32 irqholdoff_reg; + + refill_free_list(sge, &sge->freelQ[0]); + refill_free_list(sge, &sge->freelQ[1]); + + if (sge->freelQ[0].credits > (sge->freelQ[0].size >> 2) && + sge->freelQ[1].credits > (sge->freelQ[1].size >> 2)) { + irq_reg |= F_FL_EXHAUSTED; + irqholdoff_reg = sge->fixed_intrtimer; + } else { + /* Clear the F_FL_EXHAUSTED interrupts for now */ + irq_reg &= ~F_FL_EXHAUSTED; + irqholdoff_reg = sge->intrtimer_nres; + } + writel(irqholdoff_reg, adapter->regs + A_SG_INTRTIMER); + writel(irq_reg, adapter->regs + A_SG_INT_ENABLE); + + /* We reenable the Qs to force a freelist GTS interrupt later */ + doorbell_pio(adapter, F_FL0_ENABLE | F_FL1_ENABLE); +} + +#define SGE_PL_INTR_MASK (F_PL_INTR_SGE_ERR | F_PL_INTR_SGE_DATA) +#define SGE_INT_FATAL (F_RESPQ_OVERFLOW | F_PACKET_TOO_BIG | F_PACKET_MISMATCH) +#define SGE_INT_ENABLE (F_RESPQ_EXHAUSTED | F_RESPQ_OVERFLOW | \ + F_FL_EXHAUSTED | F_PACKET_TOO_BIG | F_PACKET_MISMATCH) + +/* + * Disable SGE Interrupts + */ +void t1_sge_intr_disable(struct sge *sge) +{ + u32 val = readl(sge->adapter->regs + A_PL_ENABLE); + + writel(val & ~SGE_PL_INTR_MASK, sge->adapter->regs + A_PL_ENABLE); + writel(0, sge->adapter->regs + A_SG_INT_ENABLE); +} + +/* + * Enable SGE interrupts. + */ +void t1_sge_intr_enable(struct sge *sge) +{ + u32 en = SGE_INT_ENABLE; + u32 val = readl(sge->adapter->regs + A_PL_ENABLE); + + if (sge->adapter->flags & TSO_CAPABLE) + en &= ~F_PACKET_TOO_BIG; + writel(en, sge->adapter->regs + A_SG_INT_ENABLE); + writel(val | SGE_PL_INTR_MASK, sge->adapter->regs + A_PL_ENABLE); +} + +/* + * Clear SGE interrupts. + */ +void t1_sge_intr_clear(struct sge *sge) +{ + writel(SGE_PL_INTR_MASK, sge->adapter->regs + A_PL_CAUSE); + writel(0xffffffff, sge->adapter->regs + A_SG_INT_CAUSE); +} + +/* + * SGE 'Error' interrupt handler + */ +int t1_sge_intr_error_handler(struct sge *sge) +{ + struct adapter *adapter = sge->adapter; + u32 cause = readl(adapter->regs + A_SG_INT_CAUSE); + + if (adapter->flags & TSO_CAPABLE) + cause &= ~F_PACKET_TOO_BIG; + if (cause & F_RESPQ_EXHAUSTED) + sge->stats.respQ_empty++; + if (cause & F_RESPQ_OVERFLOW) { + sge->stats.respQ_overflow++; + CH_ALERT("%s: SGE response queue overflow\n", + adapter->name); + } + if (cause & F_FL_EXHAUSTED) { + sge->stats.freelistQ_empty++; + freelQs_empty(sge); + } + if (cause & F_PACKET_TOO_BIG) { + sge->stats.pkt_too_big++; + CH_ALERT("%s: SGE max packet size exceeded\n", + adapter->name); + } + if (cause & F_PACKET_MISMATCH) { + sge->stats.pkt_mismatch++; + CH_ALERT("%s: SGE packet mismatch\n", adapter->name); + } + if (cause & SGE_INT_FATAL) + t1_fatal_err(adapter); + + writel(cause, adapter->regs + A_SG_INT_CAUSE); + return 0; +} + +const struct sge_intr_counts *t1_sge_get_intr_counts(struct sge *sge) +{ + return &sge->stats; +} + +const struct sge_port_stats *t1_sge_get_port_stats(struct sge *sge, int port) +{ + return &sge->port_stats[port]; +} + +/** + * recycle_fl_buf - recycle a free list buffer + * @fl: the free list + * @idx: index of buffer to recycle + * + * Recycles the specified buffer on the given free list by adding it at + * the next available slot on the list. + */ +static void recycle_fl_buf(struct freelQ *fl, int idx) +{ + struct freelQ_e *from = &fl->entries[idx]; + struct freelQ_e *to = &fl->entries[fl->pidx]; + + fl->centries[fl->pidx] = fl->centries[idx]; + to->addr_lo = from->addr_lo; + to->addr_hi = from->addr_hi; + to->len_gen = G_CMD_LEN(from->len_gen) | V_CMD_GEN1(fl->genbit); + wmb(); + to->gen2 = V_CMD_GEN2(fl->genbit); + fl->credits++; + + if (++fl->pidx == fl->size) { + fl->pidx = 0; + fl->genbit ^= 1; + } +} + +/** + * get_packet - return the next ingress packet buffer + * @pdev: the PCI device that received the packet + * @fl: the SGE free list holding the packet + * @len: the actual packet length, excluding any SGE padding + * @dma_pad: padding at beginning of buffer left by SGE DMA + * @skb_pad: padding to be used if the packet is copied + * @copy_thres: length threshold under which a packet should be copied + * @drop_thres: # of remaining buffers before we start dropping packets + * + * Get the next packet from a free list and complete setup of the + * sk_buff. If the packet is small we make a copy and recycle the + * original buffer, otherwise we use the original buffer itself. If a + * positive drop threshold is supplied packets are dropped and their + * buffers recycled if (a) the number of remaining buffers is under the + * threshold and the packet is too big to copy, or (b) the packet should + * be copied but there is no memory for the copy. + */ +static inline struct sk_buff *get_packet(struct pci_dev *pdev, + struct freelQ *fl, unsigned int len, + int dma_pad, int skb_pad, + unsigned int copy_thres, + unsigned int drop_thres) +{ + struct sk_buff *skb; + struct freelQ_ce *ce = &fl->centries[fl->cidx]; + + if (len < copy_thres) { + skb = alloc_skb(len + skb_pad, GFP_ATOMIC); + if (likely(skb != NULL)) { + skb_reserve(skb, skb_pad); + skb_put(skb, len); + pci_dma_sync_single_for_cpu(pdev, + pci_unmap_addr(ce, dma_addr), + pci_unmap_len(ce, dma_len), + PCI_DMA_FROMDEVICE); + memcpy(skb->data, ce->skb->data + dma_pad, len); + pci_dma_sync_single_for_device(pdev, + pci_unmap_addr(ce, dma_addr), + pci_unmap_len(ce, dma_len), + PCI_DMA_FROMDEVICE); + } else if (!drop_thres) + goto use_orig_buf; + + recycle_fl_buf(fl, fl->cidx); + return skb; + } + + if (fl->credits < drop_thres) { + recycle_fl_buf(fl, fl->cidx); + return NULL; + } + +use_orig_buf: + pci_unmap_single(pdev, pci_unmap_addr(ce, dma_addr), + pci_unmap_len(ce, dma_len), PCI_DMA_FROMDEVICE); + skb = ce->skb; + skb_reserve(skb, dma_pad); + skb_put(skb, len); + return skb; +} + +/** + * unexpected_offload - handle an unexpected offload packet + * @adapter: the adapter + * @fl: the free list that received the packet + * + * Called when we receive an unexpected offload packet (e.g., the TOE + * function is disabled or the card is a NIC). Prints a message and + * recycles the buffer. + */ +static void unexpected_offload(struct adapter *adapter, struct freelQ *fl) +{ + struct freelQ_ce *ce = &fl->centries[fl->cidx]; + struct sk_buff *skb = ce->skb; + + pci_dma_sync_single_for_cpu(adapter->pdev, pci_unmap_addr(ce, dma_addr), + pci_unmap_len(ce, dma_len), PCI_DMA_FROMDEVICE); + CH_ERR("%s: unexpected offload packet, cmd %u\n", + adapter->name, *skb->data); + recycle_fl_buf(fl, fl->cidx); +} + +/* + * Write the command descriptors to transmit the given skb starting at + * descriptor pidx with the given generation. + */ +static inline void write_tx_descs(struct adapter *adapter, struct sk_buff *skb, + unsigned int pidx, unsigned int gen, + struct cmdQ *q) +{ + dma_addr_t mapping; + struct cmdQ_e *e, *e1; + struct cmdQ_ce *ce; + unsigned int i, flags, nfrags = skb_shinfo(skb)->nr_frags; + + mapping = pci_map_single(adapter->pdev, skb->data, + skb->len - skb->data_len, PCI_DMA_TODEVICE); + ce = &q->centries[pidx]; + ce->skb = NULL; + pci_unmap_addr_set(ce, dma_addr, mapping); + pci_unmap_len_set(ce, dma_len, skb->len - skb->data_len); + + flags = F_CMD_DATAVALID | F_CMD_SOP | V_CMD_EOP(nfrags == 0) | + V_CMD_GEN2(gen); + e = &q->entries[pidx]; + e->addr_lo = (u32)mapping; + e->addr_hi = (u64)mapping >> 32; + e->len_gen = V_CMD_LEN(skb->len - skb->data_len) | V_CMD_GEN1(gen); + for (e1 = e, i = 0; nfrags--; i++) { + skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; + + ce++; + e1++; + if (++pidx == q->size) { + pidx = 0; + gen ^= 1; + ce = q->centries; + e1 = q->entries; + } + + mapping = pci_map_page(adapter->pdev, frag->page, + frag->page_offset, frag->size, + PCI_DMA_TODEVICE); + ce->skb = NULL; + pci_unmap_addr_set(ce, dma_addr, mapping); + pci_unmap_len_set(ce, dma_len, frag->size); + + e1->addr_lo = (u32)mapping; + e1->addr_hi = (u64)mapping >> 32; + e1->len_gen = V_CMD_LEN(frag->size) | V_CMD_GEN1(gen); + e1->flags = F_CMD_DATAVALID | V_CMD_EOP(nfrags == 0) | + V_CMD_GEN2(gen); + } + + ce->skb = skb; + wmb(); + e->flags = flags; +} + +/* + * Clean up completed Tx buffers. + */ +static inline void reclaim_completed_tx(struct sge *sge, struct cmdQ *q) +{ + unsigned int reclaim = q->processed - q->cleaned; + + if (reclaim) { + free_cmdQ_buffers(sge, q, reclaim); + q->cleaned += reclaim; + } +} + +#ifndef SET_ETHTOOL_OPS +# define __netif_rx_complete(dev) netif_rx_complete(dev) +#endif + +/* + * We cannot use the standard netif_rx_schedule_prep() because we have multiple + * ports plus the TOE all multiplexing onto a single response queue, therefore + * accepting new responses cannot depend on the state of any particular port. + * So define our own equivalent that omits the netif_running() test. + */ +static inline int napi_schedule_prep(struct net_device *dev) +{ + return !test_and_set_bit(__LINK_STATE_RX_SCHED, &dev->state); +} + + +/** + * sge_rx - process an ingress ethernet packet + * @sge: the sge structure + * @fl: the free list that contains the packet buffer + * @len: the packet length + * + * Process an ingress ethernet pakcet and deliver it to the stack. + */ +static int sge_rx(struct sge *sge, struct freelQ *fl, unsigned int len) +{ + struct sk_buff *skb; + struct cpl_rx_pkt *p; + struct adapter *adapter = sge->adapter; + + sge->stats.ethernet_pkts++; + skb = get_packet(adapter->pdev, fl, len - sge->rx_pkt_pad, + sge->rx_pkt_pad, 2, SGE_RX_COPY_THRES, + SGE_RX_DROP_THRES); + if (!skb) { + sge->port_stats[0].rx_drops++; /* charge only port 0 for now */ + return 0; + } + + p = (struct cpl_rx_pkt *)skb->data; + skb_pull(skb, sizeof(*p)); + skb->dev = adapter->port[p->iff].dev; + skb->dev->last_rx = jiffies; + skb->protocol = eth_type_trans(skb, skb->dev); + if ((adapter->flags & RX_CSUM_ENABLED) && p->csum == 0xffff && + skb->protocol == htons(ETH_P_IP) && + (skb->data[9] == IPPROTO_TCP || skb->data[9] == IPPROTO_UDP)) { + sge->port_stats[p->iff].rx_cso_good++; + skb->ip_summed = CHECKSUM_UNNECESSARY; + } else + skb->ip_summed = CHECKSUM_NONE; + + if (unlikely(adapter->vlan_grp && p->vlan_valid)) { + sge->port_stats[p->iff].vlan_xtract++; + if (adapter->params.sge.polling) + vlan_hwaccel_receive_skb(skb, adapter->vlan_grp, + ntohs(p->vlan)); + else + vlan_hwaccel_rx(skb, adapter->vlan_grp, + ntohs(p->vlan)); + } else if (adapter->params.sge.polling) + netif_receive_skb(skb); + else + netif_rx(skb); + return 0; +} + +/* + * Returns true if a command queue has enough available descriptors that + * we can resume Tx operation after temporarily disabling its packet queue. + */ +static inline int enough_free_Tx_descs(const struct cmdQ *q) +{ + unsigned int r = q->processed - q->cleaned; + + return q->in_use - r < (q->size >> 1); +} + +/* + * Called when sufficient space has become available in the SGE command queues + * after the Tx packet schedulers have been suspended to restart the Tx path. + */ +static void restart_tx_queues(struct sge *sge) +{ + struct adapter *adap = sge->adapter; + + if (enough_free_Tx_descs(&sge->cmdQ[0])) { + int i; + + for_each_port(adap, i) { + struct net_device *nd = adap->port[i].dev; + + if (test_and_clear_bit(nd->if_port, + &sge->stopped_tx_queues) && + netif_running(nd)) { + sge->stats.cmdQ_restarted[3]++; + netif_wake_queue(nd); + } + } + } +} + +/* + * update_tx_info is called from the interrupt handler/NAPI to return cmdQ0 + * information. + */ +static unsigned int update_tx_info(struct adapter *adapter, + unsigned int flags, + unsigned int pr0) +{ + struct sge *sge = adapter->sge; + struct cmdQ *cmdq = &sge->cmdQ[0]; + + cmdq->processed += pr0; + + if (flags & F_CMDQ0_ENABLE) { + clear_bit(CMDQ_STAT_RUNNING, &cmdq->status); + + if (cmdq->cleaned + cmdq->in_use != cmdq->processed && + !test_and_set_bit(CMDQ_STAT_LAST_PKT_DB, &cmdq->status)) { + set_bit(CMDQ_STAT_RUNNING, &cmdq->status); + writel(F_CMDQ0_ENABLE, adapter->regs + A_SG_DOORBELL); + } + flags &= ~F_CMDQ0_ENABLE; + } + + if (unlikely(sge->stopped_tx_queues != 0)) + restart_tx_queues(sge); + + return flags; +} + +/* + * Process SGE responses, up to the supplied budget. Returns the number of + * responses processed. A negative budget is effectively unlimited. + */ +static int process_responses(struct adapter *adapter, int budget) +{ + struct sge *sge = adapter->sge; + struct respQ *q = &sge->respQ; + struct respQ_e *e = &q->entries[q->cidx]; + int budget_left = budget; + unsigned int flags = 0; + unsigned int cmdq_processed[SGE_CMDQ_N] = {0, 0}; + + + while (likely(budget_left && e->GenerationBit == q->genbit)) { + flags |= e->Qsleeping; + + cmdq_processed[0] += e->Cmdq0CreditReturn; + cmdq_processed[1] += e->Cmdq1CreditReturn; + + /* We batch updates to the TX side to avoid cacheline + * ping-pong of TX state information on MP where the sender + * might run on a different CPU than this function... + */ + if (unlikely(flags & F_CMDQ0_ENABLE || cmdq_processed[0] > 64)) { + flags = update_tx_info(adapter, flags, cmdq_processed[0]); + cmdq_processed[0] = 0; + } + if (unlikely(cmdq_processed[1] > 16)) { + sge->cmdQ[1].processed += cmdq_processed[1]; + cmdq_processed[1] = 0; + } + if (likely(e->DataValid)) { + struct freelQ *fl = &sge->freelQ[e->FreelistQid]; + + if (unlikely(!e->Sop || !e->Eop)) + BUG(); + if (unlikely(e->Offload)) + unexpected_offload(adapter, fl); + else + sge_rx(sge, fl, e->BufferLength); + + /* + * Note: this depends on each packet consuming a + * single free-list buffer; cf. the BUG above. + */ + if (++fl->cidx == fl->size) + fl->cidx = 0; + if (unlikely(--fl->credits < + fl->size - SGE_FREEL_REFILL_THRESH)) + refill_free_list(sge, fl); + } else + sge->stats.pure_rsps++; + + e++; + if (unlikely(++q->cidx == q->size)) { + q->cidx = 0; + q->genbit ^= 1; + e = q->entries; + } + prefetch(e); + + if (++q->credits > SGE_RESPQ_REPLENISH_THRES) { + writel(q->credits, adapter->regs + A_SG_RSPQUEUECREDIT); + q->credits = 0; + } + --budget_left; + } + + flags = update_tx_info(adapter, flags, cmdq_processed[0]); + sge->cmdQ[1].processed += cmdq_processed[1]; + + budget -= budget_left; + return budget; +} + +/* + * A simpler version of process_responses() that handles only pure (i.e., + * non data-carrying) responses. Such respones are too light-weight to justify + * calling a softirq when using NAPI, so we handle them specially in hard + * interrupt context. The function is called with a pointer to a response, + * which the caller must ensure is a valid pure response. Returns 1 if it + * encounters a valid data-carrying response, 0 otherwise. + */ +static int process_pure_responses(struct adapter *adapter, struct respQ_e *e) +{ + struct sge *sge = adapter->sge; + struct respQ *q = &sge->respQ; + unsigned int flags = 0; + unsigned int cmdq_processed[SGE_CMDQ_N] = {0, 0}; + + do { + flags |= e->Qsleeping; + + cmdq_processed[0] += e->Cmdq0CreditReturn; + cmdq_processed[1] += e->Cmdq1CreditReturn; + + e++; + if (unlikely(++q->cidx == q->size)) { + q->cidx = 0; + q->genbit ^= 1; + e = q->entries; + } + prefetch(e); + + if (++q->credits > SGE_RESPQ_REPLENISH_THRES) { + writel(q->credits, adapter->regs + A_SG_RSPQUEUECREDIT); + q->credits = 0; + } + sge->stats.pure_rsps++; + } while (e->GenerationBit == q->genbit && !e->DataValid); + + flags = update_tx_info(adapter, flags, cmdq_processed[0]); + sge->cmdQ[1].processed += cmdq_processed[1]; + + return e->GenerationBit == q->genbit; +} + +/* + * Handler for new data events when using NAPI. This does not need any locking + * or protection from interrupts as data interrupts are off at this point and + * other adapter interrupts do not interfere. + */ +static int t1_poll(struct net_device *dev, int *budget) +{ + struct adapter *adapter = dev->priv; + int effective_budget = min(*budget, dev->quota); + + int work_done = process_responses(adapter, effective_budget); + *budget -= work_done; + dev->quota -= work_done; + + if (work_done >= effective_budget) + return 1; + + __netif_rx_complete(dev); + + /* + * Because we don't atomically flush the following write it is + * possible that in very rare cases it can reach the device in a way + * that races with a new response being written plus an error interrupt + * causing the NAPI interrupt handler below to return unhandled status + * to the OS. To protect against this would require flushing the write + * and doing both the write and the flush with interrupts off. Way too + * expensive and unjustifiable given the rarity of the race. + */ + writel(adapter->sge->respQ.cidx, adapter->regs + A_SG_SLEEPING); + return 0; +} + +/* + * Returns true if the device is already scheduled for polling. + */ +static inline int napi_is_scheduled(struct net_device *dev) +{ + return test_bit(__LINK_STATE_RX_SCHED, &dev->state); +} + +/* + * NAPI version of the main interrupt handler. + */ +static irqreturn_t t1_interrupt_napi(int irq, void *data, struct pt_regs *regs) +{ + int handled; + struct adapter *adapter = data; + struct sge *sge = adapter->sge; + struct respQ *q = &adapter->sge->respQ; + + /* + * Clear the SGE_DATA interrupt first thing. Normally the NAPI + * handler has control of the response queue and the interrupt handler + * can look at the queue reliably only once it knows NAPI is off. + * We can't wait that long to clear the SGE_DATA interrupt because we + * could race with t1_poll rearming the SGE interrupt, so we need to + * clear the interrupt speculatively and really early on. + */ + writel(F_PL_INTR_SGE_DATA, adapter->regs + A_PL_CAUSE); + + spin_lock(&adapter->async_lock); + if (!napi_is_scheduled(sge->netdev)) { + struct respQ_e *e = &q->entries[q->cidx]; + + if (e->GenerationBit == q->genbit) { + if (e->DataValid || + process_pure_responses(adapter, e)) { + if (likely(napi_schedule_prep(sge->netdev))) + __netif_rx_schedule(sge->netdev); + else + printk(KERN_CRIT + "NAPI schedule failure!\n"); + } else + writel(q->cidx, adapter->regs + A_SG_SLEEPING); + handled = 1; + goto unlock; + } else + writel(q->cidx, adapter->regs + A_SG_SLEEPING); + } else + if (readl(adapter->regs + A_PL_CAUSE) & F_PL_INTR_SGE_DATA) + printk(KERN_ERR "data interrupt while NAPI running\n"); + + handled = t1_slow_intr_handler(adapter); + if (!handled) + sge->stats.unhandled_irqs++; + unlock: + spin_unlock(&adapter->async_lock); + return IRQ_RETVAL(handled != 0); +} + +/* + * Main interrupt handler, optimized assuming that we took a 'DATA' + * interrupt. + * + * 1. Clear the interrupt + * 2. Loop while we find valid descriptors and process them; accumulate + * information that can be processed after the loop + * 3. Tell the SGE at which index we stopped processing descriptors + * 4. Bookkeeping; free TX buffers, ring doorbell if there are any + * outstanding TX buffers waiting, replenish RX buffers, potentially + * reenable upper layers if they were turned off due to lack of TX + * resources which are available again. + * 5. If we took an interrupt, but no valid respQ descriptors was found we + * let the slow_intr_handler run and do error handling. + */ +static irqreturn_t t1_interrupt(int irq, void *cookie, struct pt_regs *regs) +{ + int work_done; + struct respQ_e *e; + struct adapter *adapter = cookie; + struct respQ *Q = &adapter->sge->respQ; + + spin_lock(&adapter->async_lock); + e = &Q->entries[Q->cidx]; + prefetch(e); + + writel(F_PL_INTR_SGE_DATA, adapter->regs + A_PL_CAUSE); + + if (likely(e->GenerationBit == Q->genbit)) + work_done = process_responses(adapter, -1); + else + work_done = t1_slow_intr_handler(adapter); + + /* + * The unconditional clearing of the PL_CAUSE above may have raced + * with DMA completion and the corresponding generation of a response + * to cause us to miss the resulting data interrupt. The next write + * is also unconditional to recover the missed interrupt and render + * this race harmless. + */ + writel(Q->cidx, adapter->regs + A_SG_SLEEPING); + + if (!work_done) + adapter->sge->stats.unhandled_irqs++; + spin_unlock(&adapter->async_lock); + return IRQ_RETVAL(work_done != 0); +} + +intr_handler_t t1_select_intr_handler(adapter_t *adapter) +{ + return adapter->params.sge.polling ? t1_interrupt_napi : t1_interrupt; +} + +/* + * Enqueues the sk_buff onto the cmdQ[qid] and has hardware fetch it. + * + * The code figures out how many entries the sk_buff will require in the + * cmdQ and updates the cmdQ data structure with the state once the enqueue + * has complete. Then, it doesn't access the global structure anymore, but + * uses the corresponding fields on the stack. In conjuction with a spinlock + * around that code, we can make the function reentrant without holding the + * lock when we actually enqueue (which might be expensive, especially on + * architectures with IO MMUs). + * + * This runs with softirqs disabled. + */ +unsigned int t1_sge_tx(struct sk_buff *skb, struct adapter *adapter, + unsigned int qid, struct net_device *dev) +{ + struct sge *sge = adapter->sge; + struct cmdQ *q = &sge->cmdQ[qid]; + unsigned int credits, pidx, genbit, count; + + spin_lock(&q->lock); + reclaim_completed_tx(sge, q); + + pidx = q->pidx; + credits = q->size - q->in_use; + count = 1 + skb_shinfo(skb)->nr_frags; + + { /* Ethernet packet */ + if (unlikely(credits < count)) { + netif_stop_queue(dev); + set_bit(dev->if_port, &sge->stopped_tx_queues); + sge->stats.cmdQ_full[3]++; + spin_unlock(&q->lock); + CH_ERR("%s: Tx ring full while queue awake!\n", + adapter->name); + return 1; + } + if (unlikely(credits - count < q->stop_thres)) { + sge->stats.cmdQ_full[3]++; + netif_stop_queue(dev); + set_bit(dev->if_port, &sge->stopped_tx_queues); + } + } + q->in_use += count; + genbit = q->genbit; + q->pidx += count; + if (q->pidx >= q->size) { + q->pidx -= q->size; + q->genbit ^= 1; + } + spin_unlock(&q->lock); + + write_tx_descs(adapter, skb, pidx, genbit, q); + + /* + * We always ring the doorbell for cmdQ1. For cmdQ0, we only ring + * the doorbell if the Q is asleep. There is a natural race, where + * the hardware is going to sleep just after we checked, however, + * then the interrupt handler will detect the outstanding TX packet + * and ring the doorbell for us. + */ + if (qid) + doorbell_pio(adapter, F_CMDQ1_ENABLE); + else { + clear_bit(CMDQ_STAT_LAST_PKT_DB, &q->status); + if (test_and_set_bit(CMDQ_STAT_RUNNING, &q->status) == 0) { + set_bit(CMDQ_STAT_LAST_PKT_DB, &q->status); + writel(F_CMDQ0_ENABLE, adapter->regs + A_SG_DOORBELL); + } + } + return 0; +} + +#define MK_ETH_TYPE_MSS(type, mss) (((mss) & 0x3FFF) | ((type) << 14)) + +/* + * eth_hdr_len - return the length of an Ethernet header + * @data: pointer to the start of the Ethernet header + * + * Returns the length of an Ethernet header, including optional VLAN tag. + */ +static inline int eth_hdr_len(const void *data) +{ + const struct ethhdr *e = data; + + return e->h_proto == htons(ETH_P_8021Q) ? VLAN_ETH_HLEN : ETH_HLEN; +} + +/* + * Adds the CPL header to the sk_buff and passes it to t1_sge_tx. + */ +int t1_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct adapter *adapter = dev->priv; + struct sge_port_stats *st = &adapter->sge->port_stats[dev->if_port]; + struct sge *sge = adapter->sge; + struct cpl_tx_pkt *cpl; + +#ifdef NETIF_F_TSO + if (skb_shinfo(skb)->tso_size) { + int eth_type; + struct cpl_tx_pkt_lso *hdr; + + st->tso++; + + eth_type = skb->nh.raw - skb->data == ETH_HLEN ? + CPL_ETH_II : CPL_ETH_II_VLAN; + + hdr = (struct cpl_tx_pkt_lso *)skb_push(skb, sizeof(*hdr)); + hdr->opcode = CPL_TX_PKT_LSO; + hdr->ip_csum_dis = hdr->l4_csum_dis = 0; + hdr->ip_hdr_words = skb->nh.iph->ihl; + hdr->tcp_hdr_words = skb->h.th->doff; + hdr->eth_type_mss = htons(MK_ETH_TYPE_MSS(eth_type, + skb_shinfo(skb)->tso_size)); + hdr->len = htonl(skb->len - sizeof(*hdr)); + cpl = (struct cpl_tx_pkt *)hdr; + sge->stats.tx_lso_pkts++; + } else +#endif + { + /* + * Packets shorter than ETH_HLEN can break the MAC, drop them + * early. Also, we may get oversized packets because some + * parts of the kernel don't handle our unusual hard_header_len + * right, drop those too. + */ + if (unlikely(skb->len < ETH_HLEN || + skb->len > dev->mtu + eth_hdr_len(skb->data))) { + dev_kfree_skb_any(skb); + return NET_XMIT_SUCCESS; + } + + /* + * We are using a non-standard hard_header_len and some kernel + * components, such as pktgen, do not handle it right. + * Complain when this happens but try to fix things up. + */ + if (unlikely(skb_headroom(skb) < + dev->hard_header_len - ETH_HLEN)) { + struct sk_buff *orig_skb = skb; + + if (net_ratelimit()) + printk(KERN_ERR "%s: inadequate headroom in " + "Tx packet\n", dev->name); + skb = skb_realloc_headroom(skb, sizeof(*cpl)); + dev_kfree_skb_any(orig_skb); + if (!skb) + return -ENOMEM; + } + + if (!(adapter->flags & UDP_CSUM_CAPABLE) && + skb->ip_summed == CHECKSUM_HW && + skb->nh.iph->protocol == IPPROTO_UDP) + if (unlikely(skb_checksum_help(skb, 0))) { + dev_kfree_skb_any(skb); + return -ENOMEM; + } + + /* Hmmm, assuming to catch the gratious arp... and we'll use + * it to flush out stuck espi packets... + */ + if (unlikely(!adapter->sge->espibug_skb)) { + if (skb->protocol == htons(ETH_P_ARP) && + skb->nh.arph->ar_op == htons(ARPOP_REQUEST)) { + adapter->sge->espibug_skb = skb; + /* We want to re-use this skb later. We + * simply bump the reference count and it + * will not be freed... + */ + skb = skb_get(skb); + } + } + + cpl = (struct cpl_tx_pkt *)__skb_push(skb, sizeof(*cpl)); + cpl->opcode = CPL_TX_PKT; + cpl->ip_csum_dis = 1; /* SW calculates IP csum */ + cpl->l4_csum_dis = skb->ip_summed == CHECKSUM_HW ? 0 : 1; + /* the length field isn't used so don't bother setting it */ + + st->tx_cso += (skb->ip_summed == CHECKSUM_HW); + sge->stats.tx_do_cksum += (skb->ip_summed == CHECKSUM_HW); + sge->stats.tx_reg_pkts++; + } + cpl->iff = dev->if_port; + +#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) + if (adapter->vlan_grp && vlan_tx_tag_present(skb)) { + cpl->vlan_valid = 1; + cpl->vlan = htons(vlan_tx_tag_get(skb)); + st->vlan_insert++; + } else +#endif + cpl->vlan_valid = 0; + + dev->trans_start = jiffies; + return t1_sge_tx(skb, adapter, 0, dev); +} + +/* + * Callback for the Tx buffer reclaim timer. Runs with softirqs disabled. + */ +static void sge_tx_reclaim_cb(unsigned long data) +{ + int i; + struct sge *sge = (struct sge *)data; + + for (i = 0; i < SGE_CMDQ_N; ++i) { + struct cmdQ *q = &sge->cmdQ[i]; + + if (!spin_trylock(&q->lock)) + continue; + + reclaim_completed_tx(sge, q); + if (i == 0 && q->in_use) /* flush pending credits */ + writel(F_CMDQ0_ENABLE, + sge->adapter->regs + A_SG_DOORBELL); + + spin_unlock(&q->lock); + } + mod_timer(&sge->tx_reclaim_timer, jiffies + TX_RECLAIM_PERIOD); +} + +/* + * Propagate changes of the SGE coalescing parameters to the HW. + */ +int t1_sge_set_coalesce_params(struct sge *sge, struct sge_params *p) +{ + sge->netdev->poll = t1_poll; + sge->fixed_intrtimer = p->rx_coalesce_usecs * + core_ticks_per_usec(sge->adapter); + writel(sge->fixed_intrtimer, sge->adapter->regs + A_SG_INTRTIMER); + return 0; +} + +/* + * Allocates both RX and TX resources and configures the SGE. However, + * the hardware is not enabled yet. + */ +int t1_sge_configure(struct sge *sge, struct sge_params *p) +{ + if (alloc_rx_resources(sge, p)) + return -ENOMEM; + if (alloc_tx_resources(sge, p)) { + free_rx_resources(sge); + return -ENOMEM; + } + configure_sge(sge, p); + + /* + * Now that we have sized the free lists calculate the payload + * capacity of the large buffers. Other parts of the driver use + * this to set the max offload coalescing size so that RX packets + * do not overflow our large buffers. + */ + p->large_buf_capacity = jumbo_payload_capacity(sge); + return 0; +} + +/* + * Disables the DMA engine. + */ +void t1_sge_stop(struct sge *sge) +{ + writel(0, sge->adapter->regs + A_SG_CONTROL); + (void) readl(sge->adapter->regs + A_SG_CONTROL); /* flush */ + if (is_T2(sge->adapter)) + del_timer_sync(&sge->espibug_timer); + del_timer_sync(&sge->tx_reclaim_timer); +} + +/* + * Enables the DMA engine. + */ +void t1_sge_start(struct sge *sge) +{ + refill_free_list(sge, &sge->freelQ[0]); + refill_free_list(sge, &sge->freelQ[1]); + + writel(sge->sge_control, sge->adapter->regs + A_SG_CONTROL); + doorbell_pio(sge->adapter, F_FL0_ENABLE | F_FL1_ENABLE); + (void) readl(sge->adapter->regs + A_SG_CONTROL); /* flush */ + + mod_timer(&sge->tx_reclaim_timer, jiffies + TX_RECLAIM_PERIOD); + + if (is_T2(sge->adapter)) + mod_timer(&sge->espibug_timer, jiffies + sge->espibug_timeout); +} + +/* + * Callback for the T2 ESPI 'stuck packet feature' workaorund + */ +static void espibug_workaround(void *data) +{ + struct adapter *adapter = (struct adapter *)data; + struct sge *sge = adapter->sge; + + if (netif_running(adapter->port[0].dev)) { + struct sk_buff *skb = sge->espibug_skb; + + u32 seop = t1_espi_get_mon(adapter, 0x930, 0); + + if ((seop & 0xfff0fff) == 0xfff && skb) { + if (!skb->cb[0]) { + u8 ch_mac_addr[ETH_ALEN] = + {0x0, 0x7, 0x43, 0x0, 0x0, 0x0}; + memcpy(skb->data + sizeof(struct cpl_tx_pkt), + ch_mac_addr, ETH_ALEN); + memcpy(skb->data + skb->len - 10, ch_mac_addr, + ETH_ALEN); + skb->cb[0] = 0xff; + } + + /* bump the reference count to avoid freeing of the + * skb once the DMA has completed. + */ + skb = skb_get(skb); + t1_sge_tx(skb, adapter, 0, adapter->port[0].dev); + } + } + mod_timer(&sge->espibug_timer, jiffies + sge->espibug_timeout); +} + +/* + * Creates a t1_sge structure and returns suggested resource parameters. + */ +struct sge * __devinit t1_sge_create(struct adapter *adapter, + struct sge_params *p) +{ + struct sge *sge = kmalloc(sizeof(*sge), GFP_KERNEL); + + if (!sge) + return NULL; + memset(sge, 0, sizeof(*sge)); + + sge->adapter = adapter; + sge->netdev = adapter->port[0].dev; + sge->rx_pkt_pad = t1_is_T1B(adapter) ? 0 : 2; + sge->jumbo_fl = t1_is_T1B(adapter) ? 1 : 0; + + init_timer(&sge->tx_reclaim_timer); + sge->tx_reclaim_timer.data = (unsigned long)sge; + sge->tx_reclaim_timer.function = sge_tx_reclaim_cb; + + if (is_T2(sge->adapter)) { + init_timer(&sge->espibug_timer); + sge->espibug_timer.function = (void *)&espibug_workaround; + sge->espibug_timer.data = (unsigned long)sge->adapter; + sge->espibug_timeout = 1; + } + + + p->cmdQ_size[0] = SGE_CMDQ0_E_N; + p->cmdQ_size[1] = SGE_CMDQ1_E_N; + p->freelQ_size[!sge->jumbo_fl] = SGE_FREEL_SIZE; + p->freelQ_size[sge->jumbo_fl] = SGE_JUMBO_FREEL_SIZE; + p->rx_coalesce_usecs = 50; + p->coalesce_enable = 0; + p->sample_interval_usecs = 0; + p->polling = 0; + + return sge; +} Index: drivers/net/chelsio/sge.h =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/sge.h (mode:100644) @@ -0,0 +1,105 @@ +/***************************************************************************** + * * + * File: sge.h * + * $Revision: 1.11 $ * + * $Date: 2005/06/21 22:10:55 $ * + * Description: * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#ifndef _CXGB_SGE_H_ +#define _CXGB_SGE_H_ + +#include +#include +#include + +#ifndef IRQ_RETVAL +#define IRQ_RETVAL(x) +typedef void irqreturn_t; +#endif + +typedef irqreturn_t (*intr_handler_t)(int, void *, struct pt_regs *); + +struct sge_intr_counts { + unsigned int respQ_empty; /* # times respQ empty */ + unsigned int respQ_overflow; /* # respQ overflow (fatal) */ + unsigned int freelistQ_empty; /* # times freelist empty */ + unsigned int pkt_too_big; /* packet too large (fatal) */ + unsigned int pkt_mismatch; + unsigned int cmdQ_full[3]; /* not HW IRQ, host cmdQ[] full */ + unsigned int cmdQ_restarted[3];/* # of times cmdQ X was restarted */ + unsigned int ethernet_pkts; /* # of Ethernet packets received */ + unsigned int offload_pkts; /* # of offload packets received */ + unsigned int offload_bundles; /* # of offload pkt bundles delivered */ + unsigned int pure_rsps; /* # of non-payload responses */ + unsigned int unhandled_irqs; /* # of unhandled interrupts */ + unsigned int tx_ipfrags; + unsigned int tx_reg_pkts; + unsigned int tx_lso_pkts; + unsigned int tx_do_cksum; +}; + +struct sge_port_stats { + unsigned long rx_cso_good; /* # of successful RX csum offloads */ + unsigned long tx_cso; /* # of TX checksum offloads */ + unsigned long vlan_xtract; /* # of VLAN tag extractions */ + unsigned long vlan_insert; /* # of VLAN tag extractions */ + unsigned long tso; /* # of TSO requests */ + unsigned long rx_drops; /* # of packets dropped due to no mem */ +}; + +struct sk_buff; +struct net_device; +struct adapter; +struct sge_params; +struct sge; + +struct sge *t1_sge_create(struct adapter *, struct sge_params *); +int t1_sge_configure(struct sge *, struct sge_params *); +int t1_sge_set_coalesce_params(struct sge *, struct sge_params *); +void t1_sge_destroy(struct sge *); +intr_handler_t t1_select_intr_handler(adapter_t *adapter); +unsigned int t1_sge_tx(struct sk_buff *skb, struct adapter *adapter, + unsigned int qid, struct net_device *netdev); +int t1_start_xmit(struct sk_buff *skb, struct net_device *dev); +void t1_set_vlan_accel(struct adapter *adapter, int on_off); +void t1_sge_start(struct sge *); +void t1_sge_stop(struct sge *); +int t1_sge_intr_error_handler(struct sge *); +void t1_sge_intr_enable(struct sge *); +void t1_sge_intr_disable(struct sge *); +void t1_sge_intr_clear(struct sge *); +const struct sge_intr_counts *t1_sge_get_intr_counts(struct sge *sge); +const struct sge_port_stats *t1_sge_get_port_stats(struct sge *sge, int port); + +#endif /* _CXGB_SGE_H_ */ Index: drivers/net/chelsio/subr.c =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/subr.c (mode:100644) @@ -0,0 +1,812 @@ +/***************************************************************************** + * * + * File: subr.c * + * $Revision: 1.27 $ * + * $Date: 2005/06/22 01:08:36 $ * + * Description: * + * Various subroutines (intr,pio,etc.) used by Chelsio 10G Ethernet driver. * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Copyright (c) 2003 - 2005 Chelsio Communications, Inc. * + * All rights reserved. * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: Dimitrios Michailidis * + * Tina Yang * + * Felix Marti * + * Scott Bardone * + * Kurt Ottaway * + * Frank DiMambro * + * * + * History: * + * * + ****************************************************************************/ + +#include "common.h" +#include "elmer0.h" +#include "regs.h" +#include "gmac.h" +#include "cphy.h" +#include "sge.h" +#include "espi.h" + +/** + * t1_wait_op_done - wait until an operation is completed + * @adapter: the adapter performing the operation + * @reg: the register to check for completion + * @mask: a single-bit field within @reg that indicates completion + * @polarity: the value of the field when the operation is completed + * @attempts: number of check iterations + * @delay: delay in usecs between iterations + * + * Wait until an operation is completed by checking a bit in a register + * up to @attempts times. Returns %0 if the operation completes and %1 + * otherwise. + */ +static int t1_wait_op_done(adapter_t *adapter, int reg, u32 mask, int polarity, + int attempts, int delay) +{ + while (1) { + u32 val = readl(adapter->regs + reg) & mask; + + if (!!val == polarity) + return 0; + if (--attempts == 0) + return 1; + if (delay) + udelay(delay); + } +} + +#define TPI_ATTEMPTS 50 + +/* + * Write a register over the TPI interface (unlocked and locked versions). + */ +static int __t1_tpi_write(adapter_t *adapter, u32 addr, u32 value) +{ + int tpi_busy; + + writel(addr, adapter->regs + A_TPI_ADDR); + writel(value, adapter->regs + A_TPI_WR_DATA); + writel(F_TPIWR, adapter->regs + A_TPI_CSR); + + tpi_busy = t1_wait_op_done(adapter, A_TPI_CSR, F_TPIRDY, 1, + TPI_ATTEMPTS, 3); + if (tpi_busy) + CH_ALERT("%s: TPI write to 0x%x failed\n", + adapter->name, addr); + return tpi_busy; +} + +int t1_tpi_write(adapter_t *adapter, u32 addr, u32 value) +{ + int ret; + + spin_lock(&(adapter)->tpi_lock); + ret = __t1_tpi_write(adapter, addr, value); + spin_unlock(&(adapter)->tpi_lock); + return ret; +} + +/* + * Read a register over the TPI interface (unlocked and locked versions). + */ +static int __t1_tpi_read(adapter_t *adapter, u32 addr, u32 *valp) +{ + int tpi_busy; + + writel(addr, adapter->regs + A_TPI_ADDR); + writel(0, adapter->regs + A_TPI_CSR); + + tpi_busy = t1_wait_op_done(adapter, A_TPI_CSR, F_TPIRDY, 1, + TPI_ATTEMPTS, 3); + if (tpi_busy) + CH_ALERT("%s: TPI read from 0x%x failed\n", + adapter->name, addr); + else + *valp = readl(adapter->regs + A_TPI_RD_DATA); + return tpi_busy; +} + +int t1_tpi_read(adapter_t *adapter, u32 addr, u32 *valp) +{ + int ret; + + spin_lock(&(adapter)->tpi_lock); + ret = __t1_tpi_read(adapter, addr, valp); + spin_unlock(&(adapter)->tpi_lock); + return ret; +} + +/* + * Called when a port's link settings change to propagate the new values to the + * associated PHY and MAC. After performing the common tasks it invokes an + * OS-specific handler. + */ +/* static */ void link_changed(adapter_t *adapter, int port_id) +{ + int link_ok, speed, duplex, fc; + struct cphy *phy = adapter->port[port_id].phy; + struct link_config *lc = &adapter->port[port_id].link_config; + + phy->ops->get_link_status(phy, &link_ok, &speed, &duplex, &fc); + + lc->speed = speed < 0 ? SPEED_INVALID : speed; + lc->duplex = duplex < 0 ? DUPLEX_INVALID : duplex; + if (!(lc->requested_fc & PAUSE_AUTONEG)) + fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX); + + if (link_ok && speed >= 0 && lc->autoneg == AUTONEG_ENABLE) { + /* Set MAC speed, duplex, and flow control to match PHY. */ + struct cmac *mac = adapter->port[port_id].mac; + + mac->ops->set_speed_duplex_fc(mac, speed, duplex, fc); + lc->fc = (unsigned char)fc; + } + t1_link_changed(adapter, port_id, link_ok, speed, duplex, fc); +} + +static int t1_pci_intr_handler(adapter_t *adapter) +{ + u32 pcix_cause; + + pci_read_config_dword(adapter->pdev, A_PCICFG_INTR_CAUSE, &pcix_cause); + + if (pcix_cause) { + pci_write_config_dword(adapter->pdev, A_PCICFG_INTR_CAUSE, + pcix_cause); + t1_fatal_err(adapter); /* PCI errors are fatal */ + } + return 0; +} + + +/* + * Wait until Elmer's MI1 interface is ready for new operations. + */ +static int mi1_wait_until_ready(adapter_t *adapter, int mi1_reg) +{ + int attempts = 100, busy; + + do { + u32 val; + + __t1_tpi_read(adapter, mi1_reg, &val); + busy = val & F_MI1_OP_BUSY; + if (busy) + udelay(10); + } while (busy && --attempts); + if (busy) + CH_ALERT("%s: MDIO operation timed out\n", + adapter->name); + return busy; +} + +/* + * MI1 MDIO initialization. + */ +static void mi1_mdio_init(adapter_t *adapter, const struct board_info *bi) +{ + u32 clkdiv = bi->clock_elmer0 / (2 * bi->mdio_mdc) - 1; + u32 val = F_MI1_PREAMBLE_ENABLE | V_MI1_MDI_INVERT(bi->mdio_mdiinv) | + V_MI1_MDI_ENABLE(bi->mdio_mdien) | V_MI1_CLK_DIV(clkdiv); + + if (!(bi->caps & SUPPORTED_10000baseT_Full)) + val |= V_MI1_SOF(1); + t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_CFG, val); +} + +static int mi1_mdio_ext_read(adapter_t *adapter, int phy_addr, int mmd_addr, + int reg_addr, unsigned int *valp) +{ + u32 addr = V_MI1_REG_ADDR(mmd_addr) | V_MI1_PHY_ADDR(phy_addr); + + spin_lock(&(adapter)->tpi_lock); + + /* Write the address we want. */ + __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_ADDR, addr); + __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_DATA, reg_addr); + __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_OP, + MI1_OP_INDIRECT_ADDRESS); + mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP); + + /* Write the operation we want. */ + __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_OP, MI1_OP_INDIRECT_READ); + mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP); + + /* Read the data. */ + __t1_tpi_read(adapter, A_ELMER0_PORT0_MI1_DATA, valp); + spin_unlock(&(adapter)->tpi_lock); + return 0; +} + +static int mi1_mdio_ext_write(adapter_t *adapter, int phy_addr, int mmd_addr, + int reg_addr, unsigned int val) +{ + u32 addr = V_MI1_REG_ADDR(mmd_addr) | V_MI1_PHY_ADDR(phy_addr); + + spin_lock(&(adapter)->tpi_lock); + + /* Write the address we want. */ + __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_ADDR, addr); + __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_DATA, reg_addr); + __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_OP, + MI1_OP_INDIRECT_ADDRESS); + mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP); + + /* Write the data. */ + __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_DATA, val); + __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_OP, MI1_OP_INDIRECT_WRITE); + mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP); + spin_unlock(&(adapter)->tpi_lock); + return 0; +} + +static struct mdio_ops mi1_mdio_ext_ops = { + mi1_mdio_init, + mi1_mdio_ext_read, + mi1_mdio_ext_write +}; + +enum { + CH_BRD_N110_1F, + CH_BRD_N210_1F, +}; + +static struct board_info t1_board[] = { + +{ CHBT_BOARD_N110, 1/*ports#*/, + SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE /*caps*/, CHBT_TERM_T1, + CHBT_MAC_PM3393, CHBT_PHY_88X2010, + 125000000/*clk-core*/, 0/*clk-mc3*/, 0/*clk-mc4*/, + 1/*espi-ports*/, 0/*clk-cspi*/, 44/*clk-elmer0*/, 0/*mdien*/, + 0/*mdiinv*/, 1/*mdc*/, 0/*phybaseaddr*/, &t1_pm3393_ops, + &t1_mv88x201x_ops, &mi1_mdio_ext_ops, + "Chelsio N110 1x10GBaseX NIC" }, + +{ CHBT_BOARD_N210, 1/*ports#*/, + SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE /*caps*/, CHBT_TERM_T2, + CHBT_MAC_PM3393, CHBT_PHY_88X2010, + 125000000/*clk-core*/, 0/*clk-mc3*/, 0/*clk-mc4*/, + 1/*espi-ports*/, 0/*clk-cspi*/, 44/*clk-elmer0*/, 0/*mdien*/, + 0/*mdiinv*/, 1/*mdc*/, 0/*phybaseaddr*/, &t1_pm3393_ops, + &t1_mv88x201x_ops, &mi1_mdio_ext_ops, + "Chelsio N210 1x10GBaseX NIC" }, + +}; + +struct pci_device_id t1_pci_tbl[] = { + CH_DEVICE(7, 0, CH_BRD_N110_1F), + CH_DEVICE(10, 1, CH_BRD_N210_1F), + { 0, } +}; + +MODULE_DEVICE_TABLE(pci, t1_pci_tbl); + +/* + * Return the board_info structure with a given index. Out-of-range indices + * return NULL. + */ +const struct board_info *t1_get_board_info(unsigned int board_id) +{ + return board_id < ARRAY_SIZE(t1_board) ? &t1_board[board_id] : NULL; +} + +struct chelsio_vpd_t { + u32 format_version; + u8 serial_number[16]; + u8 mac_base_address[6]; + u8 pad[2]; /* make multiple-of-4 size requirement explicit */ +}; + +#define EEPROMSIZE (8 * 1024) +#define EEPROM_MAX_POLL 4 + +/* + * Read SEEPROM. A zero is written to the flag register when the addres is + * written to the Control register. The hardware device will set the flag to a + * one when 4B have been transferred to the Data register. + */ +int t1_seeprom_read(adapter_t *adapter, u32 addr, u32 *data) +{ + int i = EEPROM_MAX_POLL; + u16 val; + + if (addr >= EEPROMSIZE || (addr & 3)) + return -EINVAL; + + pci_write_config_word(adapter->pdev, A_PCICFG_VPD_ADDR, (u16)addr); + do { + udelay(50); + pci_read_config_word(adapter->pdev, A_PCICFG_VPD_ADDR, &val); + } while (!(val & F_VPD_OP_FLAG) && --i); + + if (!(val & F_VPD_OP_FLAG)) { + CH_ERR("%s: reading EEPROM address 0x%x failed\n", + adapter->name, addr); + return -EIO; + } + pci_read_config_dword(adapter->pdev, A_PCICFG_VPD_DATA, data); + *data = le32_to_cpu(*data); + return 0; +} + +static int t1_eeprom_vpd_get(adapter_t *adapter, struct chelsio_vpd_t *vpd) +{ + int addr, ret = 0; + + for (addr = 0; !ret && addr < sizeof(*vpd); addr += sizeof(u32)) + ret = t1_seeprom_read(adapter, addr, + (u32 *)((u8 *)vpd + addr)); + + return ret; +} + +/* + * Read a port's MAC address from the VPD ROM. + */ +static int vpd_macaddress_get(adapter_t *adapter, int index, u8 mac_addr[]) +{ + struct chelsio_vpd_t vpd; + + if (t1_eeprom_vpd_get(adapter, &vpd)) + return 1; + memcpy(mac_addr, vpd.mac_base_address, 5); + mac_addr[5] = vpd.mac_base_address[5] + index; + return 0; +} + +/* + * Set up the MAC/PHY according to the requested link settings. + * + * If the PHY can auto-negotiate first decide what to advertise, then + * enable/disable auto-negotiation as desired and reset. + * + * If the PHY does not auto-negotiate we just reset it. + * + * If auto-negotiation is off set the MAC to the proper speed/duplex/FC, + * otherwise do it later based on the outcome of auto-negotiation. + */ +int t1_link_start(struct cphy *phy, struct cmac *mac, struct link_config *lc) +{ + unsigned int fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX); + + if (lc->supported & SUPPORTED_Autoneg) { + lc->advertising &= ~(ADVERTISED_ASYM_PAUSE | ADVERTISED_PAUSE); + if (fc) { + lc->advertising |= ADVERTISED_ASYM_PAUSE; + if (fc == (PAUSE_RX | PAUSE_TX)) + lc->advertising |= ADVERTISED_PAUSE; + } + phy->ops->advertise(phy, lc->advertising); + + if (lc->autoneg == AUTONEG_DISABLE) { + lc->speed = lc->requested_speed; + lc->duplex = lc->requested_duplex; + lc->fc = (unsigned char)fc; + mac->ops->set_speed_duplex_fc(mac, lc->speed, + lc->duplex, fc); + /* Also disables autoneg */ + phy->ops->set_speed_duplex(phy, lc->speed, lc->duplex); + phy->ops->reset(phy, 0); + } else + phy->ops->autoneg_enable(phy); /* also resets PHY */ + } else { + mac->ops->set_speed_duplex_fc(mac, -1, -1, fc); + lc->fc = (unsigned char)fc; + phy->ops->reset(phy, 0); + } + return 0; +} + +/* + * External interrupt handler for boards using elmer0. + */ +int elmer0_ext_intr_handler(adapter_t *adapter) +{ + struct cphy *phy; + int phy_cause; + u32 cause; + + t1_tpi_read(adapter, A_ELMER0_INT_CAUSE, &cause); + + switch (board_info(adapter)->board) { + case CHBT_BOARD_N210: + case CHBT_BOARD_N110: + if (cause & ELMER0_GP_BIT6) { /* Marvell 88x2010 interrupt */ + phy = adapter->port[0].phy; + phy_cause = phy->ops->interrupt_handler(phy); + if (phy_cause & cphy_cause_link_change) + link_changed(adapter, 0); + } + break; + } + t1_tpi_write(adapter, A_ELMER0_INT_CAUSE, cause); + return 0; +} + +/* Enables all interrupts. */ +void t1_interrupts_enable(adapter_t *adapter) +{ + unsigned int i; + u32 pl_intr; + + adapter->slow_intr_mask = F_PL_INTR_SGE_ERR; + + t1_sge_intr_enable(adapter->sge); + if (adapter->espi) { + adapter->slow_intr_mask |= F_PL_INTR_ESPI; + t1_espi_intr_enable(adapter->espi); + } + + /* Enable MAC/PHY interrupts for each port. */ + for_each_port(adapter, i) { + adapter->port[i].mac->ops->interrupt_enable(adapter->port[i].mac); + adapter->port[i].phy->ops->interrupt_enable(adapter->port[i].phy); + } + + /* Enable PCIX & external chip interrupts on ASIC boards. */ + pl_intr = readl(adapter->regs + A_PL_ENABLE); + + /* PCI-X interrupts */ + pci_write_config_dword(adapter->pdev, A_PCICFG_INTR_ENABLE, + 0xffffffff); + + adapter->slow_intr_mask |= F_PL_INTR_EXT | F_PL_INTR_PCIX; + pl_intr |= F_PL_INTR_EXT | F_PL_INTR_PCIX; + writel(pl_intr, adapter->regs + A_PL_ENABLE); +} + +/* Disables all interrupts. */ +void t1_interrupts_disable(adapter_t* adapter) +{ + unsigned int i; + + t1_sge_intr_disable(adapter->sge); + if (adapter->espi) + t1_espi_intr_disable(adapter->espi); + + /* Disable MAC/PHY interrupts for each port. */ + for_each_port(adapter, i) { + adapter->port[i].mac->ops->interrupt_disable(adapter->port[i].mac); + adapter->port[i].phy->ops->interrupt_disable(adapter->port[i].phy); + } + + /* Disable PCIX & external chip interrupts. */ + writel(0, adapter->regs + A_PL_ENABLE); + + /* PCI-X interrupts */ + pci_write_config_dword(adapter->pdev, A_PCICFG_INTR_ENABLE, 0); + + adapter->slow_intr_mask = 0; +} + +/* Clears all interrupts */ +void t1_interrupts_clear(adapter_t* adapter) +{ + unsigned int i; + u32 pl_intr; + + + t1_sge_intr_clear(adapter->sge); + if (adapter->espi) + t1_espi_intr_clear(adapter->espi); + + /* Clear MAC/PHY interrupts for each port. */ + for_each_port(adapter, i) { + adapter->port[i].mac->ops->interrupt_clear(adapter->port[i].mac); + adapter->port[i].phy->ops->interrupt_clear(adapter->port[i].phy); + } + + /* Enable interrupts for external devices. */ + pl_intr = readl(adapter->regs + A_PL_CAUSE); + + writel(pl_intr | F_PL_INTR_EXT | F_PL_INTR_PCIX, + adapter->regs + A_PL_CAUSE); + + /* PCI-X interrupts */ + pci_write_config_dword(adapter->pdev, A_PCICFG_INTR_CAUSE, 0xffffffff); +} + +/* + * Slow path interrupt handler for ASICs. + */ +int t1_slow_intr_handler(adapter_t *adapter) +{ + u32 cause = readl(adapter->regs + A_PL_CAUSE); + + cause &= adapter->slow_intr_mask; + if (!cause) + return 0; + if (cause & F_PL_INTR_SGE_ERR) + t1_sge_intr_error_handler(adapter->sge); + if (cause & F_PL_INTR_ESPI) + t1_espi_intr_handler(adapter->espi); + if (cause & F_PL_INTR_PCIX) + t1_pci_intr_handler(adapter); + if (cause & F_PL_INTR_EXT) + t1_elmer0_ext_intr(adapter); + + /* Clear the interrupts just processed. */ + writel(cause, adapter->regs + A_PL_CAUSE); + (void)readl(adapter->regs + A_PL_CAUSE); /* flush writes */ + return 1; +} + +/* Pause deadlock avoidance parameters */ +#define DROP_MSEC 16 +#define DROP_PKTS_CNT 1 + +static void set_csum_offload(adapter_t *adapter, u32 csum_bit, int enable) +{ + u32 val = readl(adapter->regs + A_TP_GLOBAL_CONFIG); + + if (enable) + val |= csum_bit; + else + val &= ~csum_bit; + writel(val, adapter->regs + A_TP_GLOBAL_CONFIG); +} + +void t1_tp_set_ip_checksum_offload(adapter_t *adapter, int enable) +{ + set_csum_offload(adapter, F_IP_CSUM, enable); +} + +void t1_tp_set_udp_checksum_offload(adapter_t *adapter, int enable) +{ + set_csum_offload(adapter, F_UDP_CSUM, enable); +} + +void t1_tp_set_tcp_checksum_offload(adapter_t *adapter, int enable) +{ + set_csum_offload(adapter, F_TCP_CSUM, enable); +} + +static void t1_tp_reset(adapter_t *adapter, unsigned int tp_clk) +{ + u32 val; + + val = F_TP_IN_CSPI_CPL | F_TP_IN_CSPI_CHECK_IP_CSUM | + F_TP_IN_CSPI_CHECK_TCP_CSUM | F_TP_IN_ESPI_ETHERNET; + val |= F_TP_IN_ESPI_CHECK_IP_CSUM | + F_TP_IN_ESPI_CHECK_TCP_CSUM; + writel(val, adapter->regs + A_TP_IN_CONFIG); + writel(F_TP_OUT_CSPI_CPL | + F_TP_OUT_ESPI_ETHERNET | + F_TP_OUT_ESPI_GENERATE_IP_CSUM | + F_TP_OUT_ESPI_GENERATE_TCP_CSUM, + adapter->regs + A_TP_OUT_CONFIG); + + val = readl(adapter->regs + A_TP_GLOBAL_CONFIG); + val &= ~(F_IP_CSUM | F_UDP_CSUM | F_TCP_CSUM); + writel(val, adapter->regs + A_TP_GLOBAL_CONFIG); + + /* + * Enable pause frame deadlock prevention. + */ + if (is_T2(adapter)) { + u32 drop_ticks = DROP_MSEC * (tp_clk / 1000); + + writel(F_ENABLE_TX_DROP | F_ENABLE_TX_ERROR | + V_DROP_TICKS_CNT(drop_ticks) | + V_NUM_PKTS_DROPPED(DROP_PKTS_CNT), + adapter->regs + A_TP_TX_DROP_CONFIG); + } + + writel(F_TP_RESET, adapter->regs + A_TP_RESET); +} + +int __devinit t1_get_board_rev(adapter_t *adapter, const struct board_info *bi, + struct adapter_params *p) +{ + p->chip_version = bi->chip_term; + if (p->chip_version == CHBT_TERM_T1 || + p->chip_version == CHBT_TERM_T2) { + u32 val = readl(adapter->regs + A_TP_PC_CONFIG); + + val = G_TP_PC_REV(val); + if (val == 2) + p->chip_revision = TERM_T1B; + else if (val == 3) + p->chip_revision = TERM_T2; + else + return -1; + } else + return -1; + return 0; +} + +/* + * Enable board components other than the Chelsio chip, such as external MAC + * and PHY. + */ +static int board_init(adapter_t *adapter, const struct board_info *bi) +{ + switch (bi->board) { + case CHBT_BOARD_N110: + case CHBT_BOARD_N210: + writel(V_TPIPAR(0xf), adapter->regs + A_TPI_PAR); + t1_tpi_write(adapter, A_ELMER0_GPO, 0x800); + break; + } + return 0; +} + +/* + * Initialize and configure the Terminator HW modules. Note that external + * MAC and PHYs are initialized separately. + */ +int t1_init_hw_modules(adapter_t *adapter) +{ + int err = -EIO; + const struct board_info *bi = board_info(adapter); + + if (!bi->clock_mc4) { + u32 val = readl(adapter->regs + A_MC4_CFG); + + writel(val | F_READY | F_MC4_SLOW, adapter->regs + A_MC4_CFG); + writel(F_M_BUS_ENABLE | F_TCAM_RESET, + adapter->regs + A_MC5_CONFIG); + } + + if (adapter->espi && t1_espi_init(adapter->espi, bi->chip_mac, + bi->espi_nports)) + goto out_err; + + t1_tp_reset(adapter, bi->clock_core); + + err = t1_sge_configure(adapter->sge, &adapter->params.sge); + if (err) + goto out_err; + + err = 0; + out_err: + return err; +} + +/* + * Determine a card's PCI mode. + */ +static void __devinit get_pci_mode(adapter_t *adapter, struct chelsio_pci_params *p) +{ + static unsigned short speed_map[] = { 33, 66, 100, 133 }; + u32 pci_mode; + + pci_read_config_dword(adapter->pdev, A_PCICFG_MODE, &pci_mode); + p->speed = speed_map[G_PCI_MODE_CLK(pci_mode)]; + p->width = (pci_mode & F_PCI_MODE_64BIT) ? 64 : 32; + p->is_pcix = (pci_mode & F_PCI_MODE_PCIX) != 0; +} + +/* + * Release the structures holding the SW per-Terminator-HW-module state. + */ +void t1_free_sw_modules(adapter_t *adapter) +{ + unsigned int i; + + for_each_port(adapter, i) { + struct cmac *mac = adapter->port[i].mac; + struct cphy *phy = adapter->port[i].phy; + + if (mac) + mac->ops->destroy(mac); + if (phy) + phy->ops->destroy(phy); + } + + if (adapter->sge) + t1_sge_destroy(adapter->sge); + if (adapter->espi) + t1_espi_destroy(adapter->espi); +} + +static void __devinit init_link_config(struct link_config *lc, + const struct board_info *bi) +{ + lc->supported = bi->caps; + lc->requested_speed = lc->speed = SPEED_INVALID; + lc->requested_duplex = lc->duplex = DUPLEX_INVALID; + lc->requested_fc = lc->fc = PAUSE_RX | PAUSE_TX; + if (lc->supported & SUPPORTED_Autoneg) { + lc->advertising = lc->supported; + lc->autoneg = AUTONEG_ENABLE; + lc->requested_fc |= PAUSE_AUTONEG; + } else { + lc->advertising = 0; + lc->autoneg = AUTONEG_DISABLE; + } +} + + +/* + * Allocate and initialize the data structures that hold the SW state of + * the Terminator HW modules. + */ +int __devinit t1_init_sw_modules(adapter_t *adapter, + const struct board_info *bi) +{ + unsigned int i; + + adapter->params.brd_info = bi; + adapter->params.nports = bi->port_number; + adapter->params.stats_update_period = bi->gmac->stats_update_period; + + adapter->sge = t1_sge_create(adapter, &adapter->params.sge); + if (!adapter->sge) { + CH_ERR("%s: SGE initialization failed\n", + adapter->name); + goto error; + } + + if (bi->espi_nports && !(adapter->espi = t1_espi_create(adapter))) { + CH_ERR("%s: ESPI initialization failed\n", + adapter->name); + goto error; + } + + board_init(adapter, bi); + bi->mdio_ops->init(adapter, bi); + if (bi->gphy->reset) + bi->gphy->reset(adapter); + if (bi->gmac->reset) + bi->gmac->reset(adapter); + + for_each_port(adapter, i) { + u8 hw_addr[6]; + struct cmac *mac; + int phy_addr = bi->mdio_phybaseaddr + i; + + adapter->port[i].phy = bi->gphy->create(adapter, phy_addr, + bi->mdio_ops); + if (!adapter->port[i].phy) { + CH_ERR("%s: PHY %d initialization failed\n", + adapter->name, i); + goto error; + } + + adapter->port[i].mac = mac = bi->gmac->create(adapter, i); + if (!mac) { + CH_ERR("%s: MAC %d initialization failed\n", + adapter->name, i); + goto error; + } + + /* + * Get the port's MAC addresses either from the EEPROM if one + * exists or the one hardcoded in the MAC. + */ + if (vpd_macaddress_get(adapter, i, hw_addr)) { + CH_ERR("%s: could not read MAC address from VPD ROM\n", + adapter->port[i].dev->name); + goto error; + } + memcpy(adapter->port[i].dev->dev_addr, hw_addr, ETH_ALEN); + init_link_config(&adapter->port[i].link_config, bi); + } + + get_pci_mode(adapter, &adapter->params.pci); + t1_interrupts_clear(adapter); + return 0; + + error: + t1_free_sw_modules(adapter); + return -1; +} Index: drivers/net/chelsio/suni1x10gexp_regs.h =================================================================== --- /dev/null (tree:4f1caf9899c1859277082422b1fc37901c6097ac) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/drivers/net/chelsio/suni1x10gexp_regs.h (mode:100644) @@ -0,0 +1,213 @@ +/***************************************************************************** + * * + * File: suni1x10gexp_regs.h * + * $Revision: 1.9 $ * + * $Date: 2005/06/22 00:17:04 $ * + * Description: * + * PMC/SIERRA (pm3393) MAC-PHY functionality. * + * part of the Chelsio 10Gb Ethernet Driver. * + * * + * This program is free software; you can redistribute it and/or modify * + * it under the terms of the GNU General Public License, version 2, as * + * published by the Free Software Foundation. * + * * + * You should have received a copy of the GNU General Public License along * + * with this program; if not, write to the Free Software Foundation, Inc., * + * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. * + * * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED * + * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF * + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. * + * * + * http://www.chelsio.com * + * * + * Maintainers: maintainers@chelsio.com * + * * + * Authors: PMC/SIERRA * + * * + * History: * + * * + ****************************************************************************/ + +#ifndef _CXGB_SUNI1x10GEXP_REGS_H_ +#define _CXGB_SUNI1x10GEXP_REGS_H_ + +/******************************************************************************/ +/** S/UNI-1x10GE-XP REGISTER ADDRESS MAP **/ +/******************************************************************************/ +/* Refer to the Register Bit Masks bellow for the naming of each register and */ +/* to the S/UNI-1x10GE-XP Data Sheet for the signification of each bit */ +/******************************************************************************/ + +#define SUNI1x10GEXP_REG_DEVICE_STATUS 0x0004 +#define SUNI1x10GEXP_REG_MASTER_INTERRUPT_STATUS 0x000D +#define SUNI1x10GEXP_REG_GLOBAL_INTERRUPT_ENABLE 0x000E +#define SUNI1x10GEXP_REG_SERDES_3125_INTERRUPT_ENABLE 0x0102 +#define SUNI1x10GEXP_REG_SERDES_3125_INTERRUPT_STATUS 0x0104 +#define SUNI1x10GEXP_REG_RXXG_CONFIG_1 0x2040 +#define SUNI1x10GEXP_REG_RXXG_CONFIG_3 0x2042 +#define SUNI1x10GEXP_REG_RXXG_INTERRUPT 0x2043 +#define SUNI1x10GEXP_REG_RXXG_MAX_FRAME_LENGTH 0x2045 +#define SUNI1x10GEXP_REG_RXXG_SA_15_0 0x2046 +#define SUNI1x10GEXP_REG_RXXG_SA_31_16 0x2047 +#define SUNI1x10GEXP_REG_RXXG_SA_47_32 0x2048 +#define SUNI1x10GEXP_REG_RXXG_EXACT_MATCH_ADDR_1_LOW 0x204D +#define SUNI1x10GEXP_REG_RXXG_EXACT_MATCH_ADDR_1_MID 0x204E +#define SUNI1x10GEXP_REG_RXXG_EXACT_MATCH_ADDR_1_HIGH 0x204F +#define SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_LOW 0x206A +#define SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_MIDLOW 0x206B +#define SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_MIDHIGH 0x206C +#define SUNI1x10GEXP_REG_RXXG_MULTICAST_HASH_HIGH 0x206D +#define SUNI1x10GEXP_REG_RXXG_ADDRESS_FILTER_CONTROL_0 0x206E +#define SUNI1x10GEXP_REG_RXXG_ADDRESS_FILTER_CONTROL_2 0x2070 +#define SUNI1x10GEXP_REG_XRF_INTERRUPT_ENABLE 0x2088 +#define SUNI1x10GEXP_REG_XRF_INTERRUPT_STATUS 0x2089 +#define SUNI1x10GEXP_REG_XRF_DIAG_INTERRUPT_ENABLE 0x208B +#define SUNI1x10GEXP_REG_XRF_DIAG_INTERRUPT_STATUS 0x208C +#define SUNI1x10GEXP_REG_RXOAM_INTERRUPT_ENABLE 0x20C7 +#define SUNI1x10GEXP_REG_RXOAM_INTERRUPT_STATUS 0x20C8 +#define SUNI1x10GEXP_REG_MSTAT_CONTROL 0x2100 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_ROLLOVER_0 0x2101 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_ROLLOVER_1 0x2102 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_ROLLOVER_2 0x2103 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_ROLLOVER_3 0x2104 +#define SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_0 0x2105 +#define SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_1 0x2106 +#define SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_2 0x2107 +#define SUNI1x10GEXP_REG_MSTAT_INTERRUPT_MASK_3 0x2108 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_0_LOW 0x2110 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_1_LOW 0x2114 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_4_LOW 0x2120 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_5_LOW 0x2124 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_6_LOW 0x2128 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_8_LOW 0x2130 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_10_LOW 0x2138 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_11_LOW 0x213C +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_12_LOW 0x2140 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_13_LOW 0x2144 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_15_LOW 0x214C +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_16_LOW 0x2150 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_17_LOW 0x2154 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_18_LOW 0x2158 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_33_LOW 0x2194 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_35_LOW 0x219C +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_36_LOW 0x21A0 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_38_LOW 0x21A8 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_40_LOW 0x21B0 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_42_LOW 0x21B8 +#define SUNI1x10GEXP_REG_MSTAT_COUNTER_43_LOW 0x21BC +#define SUNI1x10GEXP_REG_IFLX_FIFO_OVERFLOW_ENABLE 0x2209 +#define SUNI1x10GEXP_REG_IFLX_FIFO_OVERFLOW_INTERRUPT 0x220A +#define SUNI1x10GEXP_REG_PL4ODP_INTERRUPT_MASK 0x2282 +#define SUNI1x10GEXP_REG_PL4ODP_INTERRUPT 0x2283 +#define SUNI1x10GEXP_REG_PL4IO_LOCK_DETECT_STATUS 0x2300 +#define SUNI1x10GEXP_REG_PL4IO_LOCK_DETECT_CHANGE 0x2301 +#define SUNI1x10GEXP_REG_PL4IO_LOCK_DETECT_MASK 0x2302 +#define SUNI1x10GEXP_REG_TXXG_CONFIG_1 0x3040 +#define SUNI1x10GEXP_REG_TXXG_CONFIG_3 0x3042 +#define SUNI1x10GEXP_REG_TXXG_INTERRUPT 0x3043 +#define SUNI1x10GEXP_REG_TXXG_MAX_FRAME_SIZE 0x3045 +#define SUNI1x10GEXP_REG_TXXG_SA_15_0 0x3047 +#define SUNI1x10GEXP_REG_TXXG_SA_31_16 0x3048 +#define SUNI1x10GEXP_REG_TXXG_SA_47_32 0x3049 +#define SUNI1x10GEXP_REG_XTEF_INTERRUPT_STATUS 0x3084 +#define SUNI1x10GEXP_REG_XTEF_INTERRUPT_ENABLE 0x3085 +#define SUNI1x10GEXP_REG_TXOAM_INTERRUPT_ENABLE 0x30C6 +#define SUNI1x10GEXP_REG_TXOAM_INTERRUPT_STATUS 0x30C7 +#define SUNI1x10GEXP_REG_EFLX_FIFO_OVERFLOW_ERROR_ENABLE 0x320C +#define SUNI1x10GEXP_REG_EFLX_FIFO_OVERFLOW_ERROR_INDICATION 0x320D +#define SUNI1x10GEXP_REG_PL4IDU_INTERRUPT_MASK 0x3282 +#define SUNI1x10GEXP_REG_PL4IDU_INTERRUPT 0x3283 + +/******************************************************************************/ +/* -- End register offset definitions -- */ +/******************************************************************************/ + +/******************************************************************************/ +/** SUNI-1x10GE-XP REGISTER BIT MASKS **/ +/******************************************************************************/ + +/*---------------------------------------------------------------------------- + * Register 0x0004: S/UNI-1x10GE-XP Device Status + * Bit 9 TOP_SXRA_EXPIRED + * Bit 8 TOP_MDIO_BUSY + * Bit 7 TOP_DTRB + * Bit 6 TOP_EXPIRED + * Bit 5 TOP_PAUSED + * Bit 4 TOP_PL4_ID_DOOL + * Bit 3 TOP_PL4_IS_DOOL + * Bit 2 TOP_PL4_ID_ROOL + * Bit 1 TOP_PL4_IS_ROOL + * Bit 0 TOP_PL4_OUT_ROOL + *----------------------------------------------------------------------------*/ +#define SUNI1x10GEXP_BITMSK_TOP_SXRA_EXPIRED 0x0200 +#define SUNI1x10GEXP_BITMSK_TOP_EXPIRED 0x0040 +#define SUNI1x10GEXP_BITMSK_TOP_PL4_ID_DOOL 0x0010 +#define SUNI1x10GEXP_BITMSK_TOP_PL4_IS_DOOL 0x0008 +#define SUNI1x10GEXP_BITMSK_TOP_PL4_ID_ROOL 0x0004 +#define SUNI1x10GEXP_BITMSK_TOP_PL4_IS_ROOL 0x0002 +#define SUNI1x10GEXP_BITMSK_TOP_PL4_OUT_ROOL 0x0001 + +/*---------------------------------------------------------------------------- + * Register 0x000E:PM3393 Global interrupt enable + * Bit 15 TOP_INTE + *----------------------------------------------------------------------------*/ +#define SUNI1x10GEXP_BITMSK_TOP_INTE 0x8000 + +/*---------------------------------------------------------------------------- + * Register 0x2040: RXXG Configuration 1 + * Bit 15 RXXG_RXEN + * Bit 14 RXXG_ROCF + * Bit 13 RXXG_PAD_STRIP + * Bit 10 RXXG_PUREP + * Bit 9 RXXG_LONGP + * Bit 8 RXXG_PARF + * Bit 7 RXXG_FLCHK + * Bit 5 RXXG_PASS_CTRL + * Bit 3 RXXG_CRC_STRIP + * Bit 2-0 RXXG_MIFG + *----------------------------------------------------------------------------*/ +#define SUNI1x10GEXP_BITMSK_RXXG_RXEN 0x8000 +#define SUNI1x10GEXP_BITMSK_RXXG_PUREP 0x0400 +#define SUNI1x10GEXP_BITMSK_RXXG_FLCHK 0x0080 +#define SUNI1x10GEXP_BITMSK_RXXG_CRC_STRIP 0x0008 + +/*---------------------------------------------------------------------------- + * Register 0x2070: RXXG Address Filter Control 2 + * Bit 1 RXXG_PMODE + * Bit 0 RXXG_MHASH_EN + *----------------------------------------------------------------------------*/ +#define SUNI1x10GEXP_BITMSK_RXXG_PMODE 0x0002 +#define SUNI1x10GEXP_BITMSK_RXXG_MHASH_EN 0x0001 + +/*---------------------------------------------------------------------------- + * Register 0x2100: MSTAT Control + * Bit 2 MSTAT_WRITE + * Bit 1 MSTAT_CLEAR + * Bit 0 MSTAT_SNAP + *----------------------------------------------------------------------------*/ +#define SUNI1x10GEXP_BITMSK_MSTAT_CLEAR 0x0002 +#define SUNI1x10GEXP_BITMSK_MSTAT_SNAP 0x0001 + +/*---------------------------------------------------------------------------- + * Register 0x3040: TXXG Configuration Register 1 + * Bit 15 TXXG_TXEN0 + * Bit 13 TXXG_HOSTPAUSE + * Bit 12-7 TXXG_IPGT + * Bit 5 TXXG_32BIT_ALIGN + * Bit 4 TXXG_CRCEN + * Bit 3 TXXG_FCTX + * Bit 2 TXXG_FCRX + * Bit 1 TXXG_PADEN + * Bit 0 TXXG_SPRE + *----------------------------------------------------------------------------*/ +#define SUNI1x10GEXP_BITMSK_TXXG_TXEN0 0x8000 +#define SUNI1x10GEXP_BITOFF_TXXG_IPGT 7 +#define SUNI1x10GEXP_BITMSK_TXXG_32BIT_ALIGN 0x0020 +#define SUNI1x10GEXP_BITMSK_TXXG_CRCEN 0x0010 +#define SUNI1x10GEXP_BITMSK_TXXG_FCTX 0x0008 +#define SUNI1x10GEXP_BITMSK_TXXG_FCRX 0x0004 +#define SUNI1x10GEXP_BITMSK_TXXG_PADEN 0x0002 + +#endif /* _CXGB_SUNI1x10GEXP_REGS_H_ */ + Index: include/linux/pci_ids.h =================================================================== --- 4f1caf9899c1859277082422b1fc37901c6097ac/include/linux/pci_ids.h (mode:100644) +++ e1de3eb86ea5e6ac8c5f27dc32140a0c2aacc51e/include/linux/pci_ids.h (mode:100644) @@ -2120,6 +2120,7 @@ #define PCI_DEVICE_ID_ENE_1225 0x1225 #define PCI_DEVICE_ID_ENE_1410 0x1410 #define PCI_DEVICE_ID_ENE_1420 0x1420 +#define PCI_VENDOR_ID_CHELSIO 0x1425 #define PCI_VENDOR_ID_SYBA 0x1592 #define PCI_DEVICE_ID_SYBA_2P_EPP 0x0782