Scientific Linux Fermi LTS 305 for x86_64                     Sept 26, 2005

Please send bug reports to dawson@fnal.gov,csieh@fnal.gov

----------------------------------------------------------------------------

Please read the Release Notes for Scientific Linux.  They are located at
SL.releasenote

All of the info in the SL.releasenote is valid unless this document
states otherwise.  This document only contains info that is specific
to the Fermi site. I may specifically say to read the
SL.releasenote file, this is only done to emphasize this item.

----------------------------------------------------------------------------

This is based on Scientific Linux 3.0.5, which is a rebuild of AS 3   
*including Update 5, with the following changes.  There has not been any FUE 
certification done yet.  Please read this entire document before installing.  

Table of contents

	HARDWARE REQUIREMENTS
	INSTALLATION INFO
	ADDED compared to Scientific Linux 3.0.5 
	UPDATED compared to Scientific Linux 3.0.5 
	Installer modifications
	/contrib 
	/docs
	MISC Notes
	HARDWARE SPECIFIC ISSUES
	SOFTWARE ISSUES/BUGS
	SUPPORT INFO
	vendor ERRATA

Each has a "---" line above and below it.
_____________________________________________________________________________
HARDWARE REQUIREMENTS
_____________________________________________________________________________

   The following information represents the minimum hardware requirements
   necessary to successfully install Scientific Linux Fermi LTS 3.0.5 :

   - Minimum: Sempron 64, Athlon 64, Opteron, Intel EM64T enabled Pentium 4/Xeon

   - Recommended for text-mode: 

   		- Minimum of 256MB Memory

   - Recommended for graphical: 

 		- Recommended: 256MB

   Hard Disk Space (NOTE: Additional space will be required for user data):

   - Common "Fermi Generic Desktop" Installation : 4.5GB

_____________________________________________________________________________
INSTALLATION INFO
_____________________________________________________________________________
Installation Locations

Via NFS 

  linux.fnal.gov:/export/linux/lts305/x86_64/

 with cdrom

  There is also a boot.iso which is small iso image which includes all the 
  drivers on the driver floppies and the generic boot info.  This can be used
  instead of the above floppies.  After download you can use cdrecord to
  create a cdr with this image on it.

    ftp://linux.fnal.gov/linux/lts305/x86_64/images/Fermi/boot.iso

Via CDROM

  Download and then burn cdrom iso images from

    ftp://linux.fnal.gov/linux/iso/lts305/x86_64/

-----------------------------------------------------------------------------
ADDED compared to SL 3.0.5 
-----------------------------------------------------------------------------
Acrobat

 	acroread-5.010-1.i386.rpm
 	acroread-plugin-5.010-1.i386.rpm

flpr
	
	I am installing the flpr rpm by default.  I got the latest version
	from Randy.  This does NOT require ups/upd.  The flpr binary will
	reside in /usr/local/bin/ .  This should just make using flpr
	easier for all. 

  		flpr-2.4-4f.9x.i386.rpm

Java

	Read the SL.releasenote for more info on Java.
 
        The j2re-blackdown  was discontinued because it wasn't keep up
        with security plugins as fast as we had liked.
 
Kerberos  -- Fermi version 

* 	krb5-fermi-config-1.10-1.LTS3.noarch.rpm
* 	krb5-fermi-krb5.conf-1.10-1.LTS3.noarch.rpm
 	krb5-libs-fermi-1.8a-LTS30x.1.i386.rpm
 	krb5-workstation-fermi-1.8a-LTS30x.1.i386.rpm
 
 	release 1.8a-LTS30x.1 fixes a security problem.
 	Correct permissions were put on all files
 	your old krb5.conf is now checked to see if it needs to be 
 	completely fresh or not.  If it does not need a fesh krb5.conf
 	then only the top half is changed.

  	kx509 and kxlist were added.

  	krb5-fermi-krb5.conf will ONLY put on a /etc/krb5.conf that points
  	to the fermi domain.  If you have krb5-fermi-config you DO NOT 
  	need this.  This is intended for use with the Redhat provided
	kerberos.  Many offsite users will find this of use.
	
	krb5-fermi-config-1.9-4 and later has a seperate script that only
	adds or removes aklog from your krb5.conf.  This script now get's
	run (via triggers) whenever openafs get's added or removed.

OpenAFS 
	
	See SL.releasenote

 	openafs-thiscell-FNAL-4.noarch.rpm

 		This sets up the "thiscell" to point to Fermi.

Performance Co-Pilot (PCP) config

 	Config file specific for Fermi site.

                pcp-config-2.3.0-LTS3x.2.i386.rpm

*sndconfig
*
*	Used to setup sound cards.
*	Added to maintain consistancy with i386
	
	
SL_rpm_show_arch-1.0-1.noarch.rpm

 	Changes the default output of "rpm -q <rpm name>" from
 	"name-version" to "name-version.arch"

*upsupdbootstrap
* 
* 	This version does NOT make the links in /usr/local/bin/ to /usr/bin
* 
* 	  upsupdbootstrap-4.1-1.i386.rpm
*         upsupdbootstrap-local-4.0-1.i386.rpm
*         upsupdbootstrap-generic-4.0-1.i386.rpm  	

Workgroup tag files
	
	These are used to specify which workgroup you belong to.

 	Astro-tag-3.0-4.noarch.rpm
 	BooNE-tag-3.0-4.noarch.rpm
 	BooNEDataServer-tag-3.0-5.noarch.rpm
        BTeV-tag-3.0-5.noarch.rpm
        BTeVTrigger-tag-3.0-5.noarch.rpm
	BTeVSimulation-tag-3.0-7.noarch.rpm
        BTeVWorker-tag-3.0-7.noarch.rpm
 	CDFCAFworker-tag-3.0-4.noarch.rpm
 	CDFlevel3-tag-3.0-4.noarch.rpm
 	CDFoffsite-tag-3.0-4.noarch.rpm
 	CDFonline-tag-3.0-4.noarch.rpm
 	CDF-tag-3.0-4.noarch.rpm
 	ClueD0Workstation-tag-3.0-4.noarch.rpm
 	CMSdesktop-tag-3.0-4.noarch.rpm
 	CMSfarm-tag-3.0-4.noarch.rpm
 	CMSserver-tag-3.0-4.noarch.rpm
 	ConsoleServer-tag-3.0-4.noarch.rpm
 	CPD-tag-3.0-4.noarch.rpm
 	CPDserver-tag-3.0-5.noarch.rpm
 	CSS-tag-3.0-4.noarch.rpm
 	FarmsConsole-tag-3.0-4.noarch.rpm
 	Farms-tag-3.0-4.noarch.rpm
 	FermiStandAlone-tag-3.0-4.noarch.rpm
 	FermiVeryGeneric-tag-3.0-4.noarch.rpm
 	FnaluBatch-tag-3.0-4.noarch.rpm
 	FnaluInteractive-tag-3.0-4.noarch.rpm
 	FOCUS-tag-3.0-4.noarch.rpm
 	GenericFarm-tag-3.0-4.noarch.rpm
 	Minos-tag-3.0-4.noarch.rpm
 	OAA-tag-3.0-4.noarch.rpm
 	RIP-tag-3.0-4.noarch.rpm
 	SDSS-tag-3.0-4.noarch.rpm
 	Sidet-tag-3.0-4.noarch.rpm
 	Theory-tag-3.0-4.noarch.rpm
	FermiGenericDesktopOffsite-tag-3.0-6.noarch.rpm

New workgroups

*	D0online-tag-3.0-8.noarch.rpm
*	EAG-tag-3.0-8.noarch.rpm

zz_a2ps_stdout-1.0-2.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

        Change the output of a2ps to go to stdout vs the printer.

zz_cups_nobrowse-1.0-4.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

        By default the cups deamon constantly searches the network to find
        and check on other cups printers.  This rpm turns that feature off.
	It also turns off the cupd server as it is not really needed.
 
zz_dhcp_resolv-2.2-1.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	This rpm fixes that so that when your network starts, as it checks 
	your resolv.conf, if you have dhcp.fnal.gov, but not fnal.gov it will
	put it in, so that you will have "search fnal.gov dhcp.fnal.gov" in 
	your /etc/resolv.conf file.

zz_emacs_link-1.1-3.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	Make a symbolic link from "emacs" to "xemacs" when xemacs is installed
	and emacs is not installed.  This version uses triggers to make or 
	remove the link when emacs, or xemacs is added or removed.

zz_fermi-logos

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	zz_fermi-logos-3.0.2-1.noarch.rpm
*  	redhat-artwork-0.73.2-1.LTS.i386.rpm
	redhat-artwork-0.73.2-1.LTS.x86_64.rpm
	redhat-logos-1.1.14.3-5.LTS.noarch.rpm

	Because we were required to change redhat-logos, we didn't have
	to do all the little tweeks that we were doing in zz_fermi-logos
	This version has most of those tweeks taken out.
	Since it is related, and the license permits us, we have also
	taken out the most glaring redhat logo's from redhat-artwork.
	Fixed a bug with the gdm greeeter theme.
	Put in gnome-foot for menu icon so you can tell it is gnome.

zz_firstboot_fix-1.0-1.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	Make changes to firstboot.
	1.0 - removes the question about adding users
 
zz_lang_collate-1.0-2.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	Changes LANG so that sorting is done the same as 6.1 and
	earlier.  (ABCabc instead of AaBbCc).  This is not installed by
	default except for a few workgroups.  Can be added later with
	a "yum install zz_lang_collate" .

zz_logwatch_df-1.0-2.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	By default logwatch does a df -h when looking at disk usage.  This
	can be unwanted if you have alot of NFS mounted disks.  This rpm
	change the command to be df -h -l, which looks at local disks only.

zz_ntp_configure-4.0-1.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	Configure ntp for Fermi site network.

zz_pine_user_domain-1.0-1.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	By default when a user sends mail from pine their email address
	is myname@mycomputer.fnal.gov.  This rpm changes it so that the
	default is myname@fnal.gov by modifying the /etc/pine.conf config file.

zz_rhnsd_off-1.0-1.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	This rpm turns off rhnsd, which is on by default. 

*zz_sendmail_fermi_gateway-2.0-1.noarch.rpm
*
*	This rpm is designed to send outbound sendmail e-mail through 
*	the fermilab e-mail gateway(smtp.fnal.gov).

zz_sshd_aklog-1.1-6.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.
	
	This rpm contains a script that will ensure that you have the
	correct path to aklog in your sshd_config script.  It you do not
	have AFS installed it comments out the aklog line.  This script is
	'trigger'able, so that when you update your openssh-server or your
	afs client, it will re-run to keep the sshd_config file up to date.

zz_sshd_nonkerberized-1.0-0.7.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	Fermi's openssh is normally kerberized out of the box.  This rpm 
	will make it non-kerberized.  Should only be used offsite.
	version 1.0-0.7 fixes the privilege seperation user - server start 
        problem.

zz_tcp_wrappers_change-3.0-1.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

	Disable all offsite access to common network services.  Also
	puts in the "DOE required login banners".  If it determines that
	you have already modified /etc/hosts.allow or host.deny it leaves
	them alone.
  	
zz_tex_tweaks-1.0-1.noarch.rpm

	Changed from i386 to noarch as that is what they should have been
	in the first place.

        Changes the default paper size to 8.5 x 11 vs A3
 
---------------------------------------------------------------------------
UPDATED compared to SL 3.0.5 
----------------------------------------------------------------------------
apt-get
 
 	Scientific Linux Fermi x86_64 is NOT aptable as apt does NOT understand
        a multiarch release and this release is multiarch.  It has both i386
        and x86_64 versions of some rpms.

	Only YUM is installed by default and ONLY YUM is SUPPORTED at Fermi. 

authconfig

        Authconfig needed to be tweeked because it was putting a line into
        the /etc/pam.d/system-auth that would not allow you to log into
        root or a group account if there was a .k5login file in the accounts
        home area.  This is the same change that was done in Fermi Linux 9.0.x
	We also changed it so that it quit putting the kerberos realm, as a
	line by itself in the top of krb.conf.  This was causing some
	authentications to never return.

		authconfig-4.3.7-1f2.x86_64.rpm 
		authconfig-gtk-4.3.7-1f2.x86_64.rpm

Fermi-release 

       Made change so that /etc/issue and /etc/issue.net showed Fermi
       LTS.  This is a modified SL-release.
*      Changed release number from 3.0.4 to 3.0.5

*Firefox
*
*	The only thing different than the Firefox in S.L. is the bookmarks.
*	
*	firefox-1.0.7-1.4.1.LTS3.i386.rpm
*	firefox-1.0.7-1.4.1.LTS3.x86_64.rpm

Mozilla

	Note that you can only install one arch of Mozilla.  We have 
	selected the i386 version by default as this allows for all
	the i386 version plugins to work.  If you want the x86_64 version
	you will have to remove the i386 version before installing the
	x86_64 version.
	
	   yum remove mozilla*
	   yum install mozilla.x86_64

*	mozilla-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-1.7.12-1.1.3.2.LTS3.x86_64.rpm
*	mozilla-chat-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-chat-1.7.12-1.1.3.2.LTS3.x86_64.rpm
*	mozilla-devel-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-devel-1.7.12-1.1.3.2.LTS3.x86_64.rpm
*	mozilla-dom-inspector-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-dom-inspector-1.7.12-1.1.3.2.LTS3.x86_64.rpm
*	mozilla-js-debugger-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-js-debugger-1.7.12-1.1.3.2.LTS3.x86_64.rpm
*	mozilla-mail-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-mail-1.7.12-1.1.3.2.LTS3.x86_64.rpm
*	mozilla-nspr-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-nspr-1.7.12-1.1.3.2.LTS3.x86_64.rpm
*	mozilla-nspr-devel-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-nspr-devel-1.7.12-1.1.3.2.LTS3.x86_64.rpm
*	mozilla-nss-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-nss-1.7.12-1.1.3.2.LTS3.x86_64.rpm
*	mozilla-nss-devel-1.7.12-1.1.3.2.LTS3.i386.rpm
*	mozilla-nss-devel-1.7.12-1.1.3.2.LTS3.x86_64.rpm
 

openSSH 

	Fermi version of openssh with kerberos cryptocard changes.  
	If a workgroup wants to install openssh-server then they just need 
	to add the entry from their "comps" file as it is NOT installed by
	default.
*	Staticly rebuilt with newer kerberos libraries.

*	openssh-3.5p1f12-1SL3.i386.rpm
*	openssh-askpass-3.5p1f12-1SL3.i386.rpm
*	openssh-askpass-gnome-3.5p1f12-1SL3.i386.rpm
*	openssh-clients-3.5p1f12-1SL3.i386.rpm
*	openssh-server-3.5p1f12-1SL3.i386.rpm

*redhat-lsb-1.3-3.1.LTS.305.i386.rpm
*redhat-lsb-1.3-3.1.LTS.305.x86_64.rpm
*
*	Changed to have LTS 305 be lsb compliant

Yum  -- From Duke University 

	yum-2.0.7-8.SL.noarch.rpm

	   Added a patch to enable a ia32e(EM64T) kernel to be upgraded.

*    	yum-conf-305-4.LTS.noarch.rpm

vnc
        Issue with vnc allowing more than just localhost to connect by
        default.
 
        The starting point was the latest Fedora Core SRPM of vnc,
        back-ported to use the XFree86-4.3.0-78.EL sources instead of x.org
        and javac instead of the (too-old) gcc-java, and patched to set the
        "localhostOnly" parameter to true by default. Note that it is still
        possible to return to RISKY behavior by invoking:
 
                vncserver -localhost="no" (or 0, or "off")
 
        Note that vncviewer has the new option "-via", meaning that the
        command line:
 
                vncviewer -via <host>.fnal.gov localhost:1
 
        will set up an SSH tunnel and use it to access the local vncserver
        running on <host>.fnal.gov, all in one step.
 
        NOTE that vnc is ONLY allowed if used with a SSH tunnel onsite at
        Fermi.  See the above info.
 
        Thanks to Chris Green for this patched vnc.
----------------------------------------------------------------------------
Installer modifications
---------------------------------------------------------------------------

     Kerberos is enabled by default on the normal  authentication
     screen.  The installer does NOT know if what you put in here is
     accurate so if you change something make sure it is right because
     that is what you are going to get. 

     Changes to "defaults" from vendor installer.

	Firewall is off by default.  vendor default was Medium.

	US/Central is default timezone.  vendor default was New York.

	Kerberos is on by default with a realm of FNAL.GOV .  vendor default
	was off.

	flpr

		Now installed by default.  No need for ups/upd as this is
		a rpm.

	Updated post.sh to do a full chroot to /mnt/sysimage for increased
	install RPM reliability.  (thanks to Chris Green)

---------------------------------------------------------------------------
/contrib/ 
---------------------------------------------------------------------------
The packges in this section have been contributed by various people.  They
are presented AS IS and there is no guarantee of them working.  These packages
are NOT supported by us.  They will only get security updates if the
contributor provides them.  If you have questions about them then ask the
contributor.

There are really 2 contrib trees.  One for the base Scientific Linux and one
for the Fermi site.  To use with yum you will need to uncomment out 
either/both of the "contrib" lines in /etc/yum.conf

See README's in the RPMS/ directorys for specific info.

/sites/Fermi/contrib/RPMS/

/contrib/RPMS/

---------------------------------------------------------------------------
MISC NOTES
---------------------------------------------------------------------------
---------------------------------------------------------------------------
SUPPORT INFO
---------------------------------------------------------------------------
Fermi site users should start with the "Fermi" specific support areas and
use the Scientific Linux next.

Fermi Linux web pages

	http://www.fnal.gov/cd/unix/linux

Fermi Linux Community support mailing list

  linux-users@fnal.gov

	Which is archived at 

		http://listserv.fnal.gov/archives/linux-users.html

Scientific Linux web page

	http://www.scientificlinux.org	

--------------------------------------------------------------------------
ERRATA added after the release of SL 3.0.5
--------------------------------------------------------------------------

* 	squid-2.5.STABLE3-6.3E.14.x86_64.rpm
* 	XFree86-100dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-4.3.0-95.EL.x86_64.rpm
* 	XFree86-75dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-base-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-cyrillic-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-devel-4.3.0-95.EL.i386.rpm
* 	XFree86-devel-4.3.0-95.EL.x86_64.rpm
* 	XFree86-doc-4.3.0-95.EL.x86_64.rpm
* 	XFree86-font-utils-4.3.0-95.EL.x86_64.rpm
* 	XFree86-ISO8859-14-100dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-ISO8859-14-75dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-ISO8859-15-100dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-ISO8859-15-75dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-ISO8859-2-100dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-ISO8859-2-75dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-ISO8859-9-100dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-ISO8859-9-75dpi-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-libs-4.3.0-95.EL.x86_64.rpm
* 	XFree86-libs-4.3.0-95.EL.i386.rpm
* 	XFree86-libs-data-4.3.0-95.EL.x86_64.rpm
* 	XFree86-Mesa-libGL-4.3.0-95.EL.i386.rpm
* 	XFree86-Mesa-libGL-4.3.0-95.EL.x86_64.rpm
* 	XFree86-Mesa-libGLU-4.3.0-95.EL.i386.rpm
* 	XFree86-Mesa-libGLU-4.3.0-95.EL.x86_64.rpm
* 	XFree86-sdk-4.3.0-95.EL.x86_64.rpm
* 	XFree86-syriac-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-tools-4.3.0-95.EL.x86_64.rpm
* 	XFree86-truetype-fonts-4.3.0-95.EL.x86_64.rpm
* 	XFree86-twm-4.3.0-95.EL.x86_64.rpm
* 	XFree86-xauth-4.3.0-95.EL.x86_64.rpm
* 	XFree86-xdm-4.3.0-95.EL.x86_64.rpm
* 	XFree86-xfs-4.3.0-95.EL.x86_64.rpm
* 	XFree86-Xnest-4.3.0-95.EL.x86_64.rpm
* 	XFree86-Xvfb-4.3.0-95.EL.x86_64.rpm
* 	cvs-1.11.2-28.x86_64.rpm
* 	httpd-2.0.46-46.3.ent.x86_64.rpm
* 	httpd-devel-2.0.46-46.3.ent.x86_64.rpm
* 	mod_ssl-2.0.46-46.3.ent.x86_64.rpm
* 	pcre-3.9-10.2.i386.rpm
* 	pcre-3.9-10.2.x86_64.rpm
* 	pcre-devel-3.9-10.2.x86_64.rpm
*       evolution-1.4.5-16.x86_64.rpm
*       evolution-devel-1.4.5-16.x86_64.rpm
*       netpbm-9.24-11.30.2.x86_64.rpm
*       netpbm-9.24-11.30.2.i386.rpm
*       netpbm-devel-9.24-11.30.2.x86_64.rpm
*       netpbm-progs-9.24-11.30.2.x86_64.rpm
*       vim-common-6.3.046-0.30E.4.x86_64.rpm
*       vim-enhanced-6.3.046-0.30E.4.x86_64.rpm
*       vim-minimal-6.3.046-0.30E.4.x86_64.rpm
*       vim-X11-6.3.046-0.30E.4.x86_64.rpm
*       cups-1.1.17-13.3.31.x86_64.rpm
*       cups-devel-1.1.17-13.3.31.x86_64.rpm
*       cups-libs-1.1.17-13.3.31.i386.rpm
*       cups-libs-1.1.17-13.3.31.x86_64.rpm
*       ethereal-0.10.12-1.EL3.1.x86_64.rpm
*       ethereal-gnome-0.10.12-1.EL3.1.x86_64.rpm
*       gaim-1.3.1-0.el3.3.x86_64.rpm
*       php-4.3.2-25.ent.x86_64.rpm
*       php-devel-4.3.2-25.ent.x86_64.rpm
*       php-imap-4.3.2-25.ent.x86_64.rpm
*       php-ldap-4.3.2-25.ent.x86_64.rpm
*       php-mysql-4.3.2-25.ent.x86_64.rpm
*       php-odbc-4.3.2-25.ent.x86_64.rpm
*       php-pgsql-4.3.2-25.ent.x86_64.rpm
*       squirrelmail-1.4.3a-10.EL3.noarch.rpm
*       sysreport-1.3.7.2-9.noarch.rpm